Rotor Manual Parts

• Pumps but will not spin
• Will not agitate
• Burning smell
• Touchpad does not respond

My whirlpool washer was no longer spinning, so my first stop was YouTube where I found the video from AppliancePartsPros showing how to replace the motor coupling. In addition to the replacement guide, Matt also shows you how to diagnose the problem by looking for rubber shavings under the washer. Seeing the rubber shavings under the washer, combined with the fact that the washer still drained meant that the motor was still working, so something else in the drive train was bad. I took the... Read more

• Will not tumble
• Noisy
• Shuts off too soon

My 12 year old Kenmore dryer problem started about 3 years ago with the motor just stopping. My thing was: I would turn it off and turn the drum by hand about halfway around and it would work again. Last month, my wife said it stopped again and its making a loud noise, but when I did "my thing" it still made a loud squealing noise (like I was killing a mouse). I made time to work on it the next day, I took it apart, using the video instructions from AppliancePartsPros, I removed the top,... Read more

• Burning smell

All's well that ends well, but the getting there was a bit of a pain. The web site suggests 3 possible causes for my problem (incl. the burning smell). I began with the first two since they were inexpensive compared to the motor, which was the third cause (and also the least often cause). There is no way to visibly tell if the motor is bad or not. After replacing the clutch assembly, which did have some plastic pins broken off) and the motor coupling (which actually looked fine, but the... Read more

• Will not agitate
• won't spin

My washer would not spin. This fixed my problem only took me 5 minutes to uninstall and install. Read more

• Will not tumble

This was a Maytag DE312 actually a Whirlpool labeled as Maytag) and is 27 years old. Replaced motor, drive belt and drum rollers. One tricky part was the motor because the new motor comes with integral starter and it was necessary to cut off existing female spade connectors on some wires and crimp on new connectors. Instructions were adequate but need to be carefully followed and a decent electrical stripping and crimping tool must be at hand. I bought a new motor drive pulley because another... Read more

• Won't start

I removed the belt and found with no load the motor ran but made a grinding noise. I purchased a new motor and installed it. The fix was easy and quick. Read more

Had to replace motor and blower, and both were very easy fixes, both pieces fit just right. The do it yourself videos also helped alot too, so props to them...Thanx alot Read more

I ordered the new part from you and the new rotor assembly came with a metal spline which looks to be much more durable. The repair was very easy. It took less than 10 minutes after watching your youtube video. I found your videos very helpful and watching them help me avoid replacing the wrong parts!. Thanks for your help and quick shipping. Read more

First off I want to say Appliance Part Pros rock! I have used them for purchasing repair items for other appliances in the past, so when my washer started making weird noises this was my go to source. I thought my problem was likely pump motor related as the water wasn't draining and I could hear the sound of the pump trying to work. After reviewing what others who had similar situations found to be the problem I took a gamble and decided to get the drain pump. Some who had that problem... Read more

Saw a video on line. Looked fairly easy to replace, but there were quite a few steps. I followed the video step for step and had the motor out in less than an hour. Tested motor with an electrical tester, just to be sure that was the problem. I ordered the motor from Appliance Parts Pros on a Sunday evening. The motor was at my doorstep Tuesday morning. It took about a hour and half to get everything back together. My only suggestion would be to label all the screws as to where they go as you... Read more

I ordered a new motor with a very helpful Chris.It arrived a day later with instructions and was easy to exchange with the old one.I am delighted with how it works and the price was good and the service excellent.thank you. Read more

Watched a You tube video, showed how to remove bottom, unhook wiring, then proceed to top case. Once removed, case is turned upside down so the capture nut can be installed. Part fit perfectly and BAM, done. Case refitted and finished. Part arrived in 2 days. Great service. Read more

• Will not agitate

Swapped bad part for new part. Read more

• Will not agitate
• Burning smell

The washer was on, and I heard a faint humming sound in the laundry room. I went in and opened the washer and it was full of soapy water in the middle of its cycle and was not agitating. I also smelled a faint burning smell. At this point I figured the problem was a bad motor, as the washer is more than 20 years old. I have fixed it twice before, because the first time, the repairman said I should keep this washer going as long as possible. It was made to last with a metal drum, unlike newer... Read more

I used the internet and checked a dry fuse, and it tested ok. Checked the start switch, ok. So it had to be the motor. Sharon at the company agreed. Motor, and belt arrive very fast. ordered the belt because, if I had it apart why not change it. Internet also helped get the dryer apart. Found on u-tube a repairman cut a hole in the side to gain easy access. This dryer is not easy to work on, but this helped, and will make further repairs much easier. Using the internet, and... Read more

Unplugged power cord, shut off hot and cold water valves, and disconnected hot and cold water lines. I taped the lid closed and laid washer down on its front panel to access motor parts underneath. Removed center screw (allen wrench) and then removed large, round, plastic rotor (had to use some force with fingers behind it to get it off). I could see that the gear teeth inside the rotor had been partially stripped off ruining the rotor (and causing the noise). I then removed the clutch... Read more