Rotor Nut Parts

• Pumps but will not spin
• Will not agitate
• Burning smell
• Touchpad does not respond

My whirlpool washer was no longer spinning, so my first stop was YouTube where I found the video from AppliancePartsPros showing how to replace the motor coupling. In addition to the replacement guide, Matt also shows you how to diagnose the problem by looking for rubber shavings under the washer. Seeing the rubber shavings under the washer, combined with the fact that the washer still drained meant that the motor was still working, so something else in the drive train was bad. I took the... Read more

• Will not tumble
• Noisy
• Shuts off too soon

My 12 year old Kenmore dryer problem started about 3 years ago with the motor just stopping. My thing was: I would turn it off and turn the drum by hand about halfway around and it would work again. Last month, my wife said it stopped again and its making a loud noise, but when I did "my thing" it still made a loud squealing noise (like I was killing a mouse). I made time to work on it the next day, I took it apart, using the video instructions from AppliancePartsPros, I removed the top,... Read more

I replaced the washer plate and new screw/washer part. Easy fix and back up and running in ubder 10 minutes. Read more

• Burning smell

All's well that ends well, but the getting there was a bit of a pain. The web site suggests 3 possible causes for my problem (incl. the burning smell). I began with the first two since they were inexpensive compared to the motor, which was the third cause (and also the least often cause). There is no way to visibly tell if the motor is bad or not. After replacing the clutch assembly, which did have some plastic pins broken off) and the motor coupling (which actually looked fine, but the... Read more

• Will not tumble

This was a Maytag DE312 actually a Whirlpool labeled as Maytag) and is 27 years old. Replaced motor, drive belt and drum rollers. One tricky part was the motor because the new motor comes with integral starter and it was necessary to cut off existing female spade connectors on some wires and crimp on new connectors. Instructions were adequate but need to be carefully followed and a decent electrical stripping and crimping tool must be at hand. I bought a new motor drive pulley because another... Read more

I ordered a replacement handle and screws. The process was very easy with the help of one of your "pros" who found all the parts needed and took my order. I didn't realize I was getting both a refrigerator door handle and a freezer door handle in one set, but now we have the freezer handle if we need it. Removing the old handle and installing the replacement was very easy. It looks great, in fact the replacement is metal, whereas the original was plastic, so it looks better than it ever did! Read more

• Will not agitate
• won't spin

My washer would not spin. This fixed my problem only took me 5 minutes to uninstall and install. Read more

• Won't start

I removed the belt and found with no load the motor ran but made a grinding noise. I purchased a new motor and installed it. The fix was easy and quick. Read more

The bar retainers just snapped in and the door handle can be replaced with three screws. Took about 5 minutes total. Read more

Had to replace motor and blower, and both were very easy fixes, both pieces fit just right. The do it yourself videos also helped alot too, so props to them...Thanx alot Read more

Removing the bottom panel and watching the internals while the washer was running revealed a small drip from what appeared to be a plastic cam that was attached to a solenoid. The water was dripping from the shaft the cam attached to down into the solenoid. Being a DIY guy I pulled the washer out, turned it upside down and inspected the effected mechanism. It appeared that there was a seal on the shaft that was leaking. The water leaking into the solenoid caused it to rust and stick. A quick... Read more

I ordered the new part from you and the new rotor assembly came with a metal spline which looks to be much more durable. The repair was very easy. It took less than 10 minutes after watching your youtube video. I found your videos very helpful and watching them help me avoid replacing the wrong parts!. Thanks for your help and quick shipping. Read more

Saw a video on line. Looked fairly easy to replace, but there were quite a few steps. I followed the video step for step and had the motor out in less than an hour. Tested motor with an electrical tester, just to be sure that was the problem. I ordered the motor from Appliance Parts Pros on a Sunday evening. The motor was at my doorstep Tuesday morning. It took about a hour and half to get everything back together. My only suggestion would be to label all the screws as to where they go as you... Read more

First off I want to say Appliance Part Pros rock! I have used them for purchasing repair items for other appliances in the past, so when my washer started making weird noises this was my go to source. I thought my problem was likely pump motor related as the water wasn't draining and I could hear the sound of the pump trying to work. After reviewing what others who had similar situations found to be the problem I took a gamble and decided to get the drain pump. Some who had that problem... Read more

I ordered a new motor with a very helpful Chris.It arrived a day later with instructions and was easy to exchange with the old one.I am delighted with how it works and the price was good and the service excellent.thank you. Read more

• Door won't open or close

My 10 year old frig door was hanging down to the point it wasnt fully closing and sealing unless you picked up on it. I ordered a lower hinge bracket, upper and lower bearing, and spacer. My bracket was bent down a little due to my kids hanging on the door when looking at the bottom shelf and i discovered my bracket was held on by only two bolts when there was supposed to be three. I ordered a bolt too. I was able to remove the bottom hinge, remove door to replace upper and lower bearing and... Read more