Timer Number131436800 Parts

I started with Google searches for the problem, using the dishwasher model number to narrow down the number of results. When I found several posts in the forum on AppliancePartsPros.com from other people having the same problem with the same dishwasher, as well as solutions that involved replacing the control board, I decided to start with that. The repair was very easy, especially with the help of clear and well-paced videos showing exactly what to do and what to look for. I was able to... Read more

Indicator light would blink three times, make a sound, but the dishwasher would not run. After making sure there were no obstructions, no problems with seals, filters, and latch clean, I cut the power off and back on. The Dishwasher worked for a few more times. After that, cutting the power off and on no longer worked. I figured out what buttons to press and hold to find the error code (start/stop and cycle select), saw code 815, and then did a "hard reset" by pressing and holding other... Read more

Two weeks ago, my dishwasher would not run. It would beep three times when you pushed the start button: the same signal it gives when the door is open. I used the troubleshooting steps I found at applianceblog.com to do a hard reset. (Hold START and WASH TEMP for five seconds, close the door, and wait 3 minutes) After that, it worked for about one week. When it started having the same issue again, the hard reset did not work. I lowered the control board and could see that there were no lights.... Read more

After calling Whirlpool customer support learned that a replacement timer would be $136. The CSR gave me the part number needed. Online I found AppliacePartsPros. I called and got a very personable CSR who took my order. I was assured the part was a genuine, new--not rebuilt--timer. My order was placed in minutes. Although I ordered standard shipping and my part arrived in 2 days!! Unfortunately Whirlpool had given me the wrong part number so I contacted AppliancePartsPros and reordered... Read more

Replaced control board myself. Easy. Read more

• Frost buildup
• Fridge runs too long
• Freezer too cold
• Freezer not defrosting

My problem first showed up as varying temperature in both sections of my old mid 1970’s Frigidaire model FPCI-170T-7 refrigerator, which is not listed on most appliance repair databases. Running on the warm side from time to time, as well as sudden fan noise (probably the fan blade hitting ice build-up on the evaporator coil) alerted me to a possible defrost system problem, since the compressor was cooling. The evaporator fan eventually failed after a day or so, and a major repair was... Read more

My GE dishwasher (GDT605PMM0ES) had started going in and out of service but if I unplugged it and plugged it back in it would work a few more times. Then one day that old trick didn't work anymore. Looked at what might be the issue on the internet and most signs pointed to the configured service machine control board or the configured Ui board. I ordered both, not really which was bad, but started with the Ui board first because the service machine control board showed it was receiving... Read more

Ordered a new timer and knob. The husband was able to fix in about 20 minutes and now works like new. Read more

The fix was very easy. Control assembly is easy to access by removing 5 phillips screws. Unplug the wiring from the old assembly being careful to note which wire goes to which connector. Install the new assembly and connect the wiring. Read more

GE Washer m/n GTW460ASJ6WW would allow other fill levels, but when set to "super" it would never stop filling. Checked water inlet valve (by initiating a fill and unplugging the unit) to see if the inlet valve was sticking open, that was not the issue. Decided to replace the board even though it is a significant fraction of the cost of a new washer. Local appliance stores didn't have the board but APP did, and of course, they are open 24/7 while my local part stores have decided the weekend is... Read more

• Too warm
• Fridge runs too long
• Fridge too cold
• Frost buildup

A word of thanks to AppliancePartsPros - they delivered in one day. Ordered at 4PM CDT and received the part by noon the next day. Also, Alicia in the help department was able to locate an electrical diagram for my old freezer. This was essential for proper setup and her persistence in tracking down the diagram was top notch. Now on to my problem. One day I opened the freezer and found frost and thawing food. I attributed this to the door hitting an item in the freezer and not completely... Read more

Ordered new timer and fixed the problem Read more

The selector knob and timer quit working on our GE dryer. We noticed the plastic selector knob was cracked inside when we pulled it off. We decided to order a new timer along with the selector knob just in case the new knob didn't solve the problem. We put on the new knob as easy as we pulled it off and the dryer would turn on again, however it was not going off in the selected amount of time it was supposed to. So it turns out we did need the timer part as well. These parts came in the... Read more

The control went thru a month or so of erratic behavior; the display would come on and flash and beep without any input on my part. Then it died completely. I did a little research on the GE website and determined likely cause waa a defective user interface board. I found AppliancePartsPros.com and contacted their tech support, who directed me to check the output of the control board across 2 pins for 13.5v DC. I did this, and measured 13.8v, so control board was good. When I reconnected the... Read more

• Shuts off too soon

After taking the timer apart to see why it would not turn I found the timer motor was jammed. Taking the motor apart I found a broken gear. Looked up the model number of the dryer and found a new timer assembly thru appliancepartspros.com I ordered, a very easy process, received the part 2 days later. Installed the assembly in about 5minutes and had the dryer back up and running Read more

I read a few of your reviews and found that a, "Phase Control Board" may be the problem. It was! Talk about easy to install... It was super easy! I decided to order the, "Speed Control Plate" also as a precaution (Shipping was one price - and it arrived the very next day, Wow! I didn't expect that.) With my screwdriver and good lighting. I fixed it myself! My husband is still in shock. I used forceps to install the, "Speed Control Plate," because I needed something to hold the tension wire - at... Read more