Parts for Lg WM1333HW / AOWEEUS: Section 3 Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Supports the washer drum for smooth, quiet spinning. Replace if you hear grinding noises or excessive vibration during cycles. Confirm fit with your model.

Washer won't spin or makes grinding noises? The motor rotor bolt secures the rotor to the motor shaft. Requires a 17mm socket for installation.

Seals between inner and outer tubs to prevent water leaks during wash cycles. Replace if you notice leaks or after bearing replacement. Verify fit.

This balance weight stabilizes the washer drum to reduce vibration and keep the washer steady during spin cycles. Replacing a worn or damaged weight restores smoother operation and reduces shaking and noise. What it does:

• Adds mass to the washer frame/drum assembly so the tub stays balanced during spin
• Helps prevent excessive vibration, banging, and movement during high-speed spins
• Reduces noise caused by an unbalanced load or damaged weight
• Supports proper drum alignment to avoid premature wear on bearings and suspension parts

• One balance weight

• Always unplug the washer before starting any repair to avoid electrical shock
• Support the drum/tub when removing or installing the weight to prevent component damage
• Reuse or replace any mounting hardware only if explicitly specified by the manufacturer
• If vibration persists after replacement, inspect suspension, shock absorbers, and mounting points

This replacement refrigerator door gasket seals the door to keep cold air inside, helping restore proper cooling and reduce frost, condensation, and energy loss from a damaged or worn seal. What it does:

• Creates an airtight seal around the refrigerator door to maintain internal temperature.
• Prevents warm air infiltration that can cause frost buildup and uneven cooling.
• Reduces condensation and helps improve compressor efficiency when sealing properly.
• Common symptoms of a failing gasket: visible cracks or gaps, cold air leaks, frost or moisture buildup, and higher energy use.

• Remove the old gasket and clean the door flange before installing the new seal.
• Press the gasket evenly into the door channel; some models use retaining clips or screws—model-specific instructions.
• Check that the gasket seats uniformly with the door closed and make minor adjustments as needed.

Fix TE error code on your washer with this thermistor assembly. Monitors water temperature during wash cycles. DIY-friendly repair with video guide.

Seals the front-load washer door to prevent water leaks. Replace if worn, torn, or brittle to restore watertight seal. Confirm fit with your model.

Heater assembly for washer dryer combos. Installs in the drying system to generate heat. Replace if cracked, corroded, or damaged to restore proper drying.

Washer won't drain or shows OE error? This drain pump assembly removes water during spin cycle. Moderate DIY repair with video guide available.

Joins washer plumbing lines to create a watertight seal. Replace your cracked, damaged, or leaking connector to restore secure water routing between hoses.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Lint filter screen for washer dryer combos. Replace when clogged to prevent drain errors and maintain proper airflow. Verify fit with your model number.

Washer won't spin or agitate? A faulty stator assembly disrupts the magnetic field needed to drive the motor. Restores normal drum rotation.

This rotor position sensor (Hall sensor) tracks the direct-drive motor's rotor position and speed so the control can commutate the washer motor accurately. Replacing a failed sensor can restore proper wash/agitate and spin performance. What it does:

• Detects rotor position and speed from the stator assembly
• Sends timing feedback to the control for correct motor start, direction, and speed
• Supports smooth agitation and spin ramp-up/ramp-down
• Failure may cause: no spin or agitation, cycle stalling/pausing, or an LE motor error code

• 1 rotor position sensor assembly

• Unplug the washer and shut off water; wear protective gloves
• Access the motor at the rear of the tub; remove the back panel if needed
• Remove the rotor and stator; support the stator to protect wiring, then unclip/unscrew and replace the sensor
• Align the sensor correctly and seat the connector fully before reassembly and testing

Replace your washer's hinge spring if it's broken, stretched, or missing. This spring helps support the lid or door mechanism during opening and closing.

Supports suspension springs that stabilize the washer drum, reducing vibration and noise during operation. Replace if drum shakes excessively or hits sides. Verify fit with your model number.

Secures rubber hoses to fittings with constant spring tension to prevent leaks. Replace when rusted or weakened to maintain a tight seal. Confirm fit.

This replacement clamp secures flexible hoses and tubing to fittings to help prevent leaks and keep connections stable. It's a small but essential part for reliable water and drain line performance. What it does:

• Holds hoses or tubes firmly to barbs, fittings, or posts to prevent disconnection
• Helps reduce leaks and water seepage at hose connections
• Minimizes rattling or vibration from loose tubing
• Supports proper routing of lines to avoid kinks or wear

• Disconnect power and water supply before starting any repair
• Use appropriate hand tools (pliers or a screwdriver, depending on clamp type) and avoid over-tightening
• Inspect nearby hoses and fittings for wear and replace if damaged

Fix washer leaks with this hose clamp. Secures hoses to pumps and valves, preventing water leaks and disconnections during wash cycles. Simple repair.

Air chamber dome for washer pressure systems. Installs on the tub assembly to regulate water level sensing. Replace if cracked, damaged, or missing.

Replaces worn or broken shock absorbers that stabilize the drum in your washer. Installs at the base of the tub to dampen vibrations during spin cycles.

Replaces worn or broken shock absorbers that stabilize the drum in your washer. Installs at the base of the tub to dampen vibrations during spin cycles.

Locking pin for shock absorber.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.