Parts for Electrolux E23BC79SPS4: System Parts

Removes odors and keeps food fresh. Replace every 6 months for optimal performance. Located in the door under dairy compartment. Confirm fit by model.

Molded plastic air deflector that directs cold airflow inside your refrigerator. Replace this part if cracked, broken, or missing to restore proper venting.

Refrigerator not cooling properly? This condenser coil assembly removes heat from refrigerant to restore cooling performance and improve efficiency.

Evaporator coil assembly for bottom-mount refrigerators. Installs in the freezer compartment. Replace if damaged, leaking, or insulation is deteriorated.

Freezer not cooling below 32°F or water leaking under freezer? The drier filter removes moisture from the refrigerant system. Soldering required.

Connects your refrigerator to the wall outlet to supply electricity. Replace if the original cord is frayed, damaged, or has exposed wires from wear or moving.

Fix frost buildup on evaporator coils causing warm temps or freezer icing. This defrost heater melts accumulated ice. DIY repair in 30-40 minutes.

Refrigerator not cooling or freezing over? This evaporator coil absorbs heat to keep your fridge cold. Intermediate repair requiring 2-3 hours work.

Aluminum strap secures the defrost heater against the evaporator coil. Replace if broken, cracked, or missing to maintain proper heater contact.

Replace your refrigerator door gasket to restore a tight seal, maintain proper cooling, and reduce energy costs. Prevents cold air leaks and frost buildup.

Fix inconsistent cooling or frost buildup with this refrigerator thermistor. Monitors compartment temperature and signals the control board. Straightforward DIY repair.

Mounting screw for refrigerator components and panels. Replaces lost, stripped, or damaged screws. Essential hardware for secure assembly.

Ice buildup in your freezer? This defrost thermostat monitors temperature and triggers defrost cycles. Fixes frost on rear panels and ice maker areas.

Rubber grommet that mounts and cushions the compressor to reduce vibration transfer. Replace if cracked, worn, or missing to restore quiet operation.

Secures the compressor to the mounting bracket in your refrigerator. Replace if washer is missing, cracked, or worn to restore proper support.

Clip spring for refrigerator shelves and compartments. Replaces broken, missing, or worn clips that secure parts in place. Direct fit replacement.

Replacement defrost drain pan that collects and channels meltwater from the automatic defrost cycle. Replace if cracked, warped, or missing to prevent leaks.

Refrigerator not cooling or running constantly? The compressor circulates refrigerant to maintain temperature. Professional installation recommended.

Fix warm fridge or inconsistent cooling caused by a failed compressor inverter. This module powers variable-speed compressors. Moderate DIY repair.

Rubber grommet that cushions and protects door components in your refrigerator. Replace if cracked, worn, or missing to restore proper door function.

Secures panels, brackets, and assemblies in refrigerators and freezers. Replace missing, stripped, or damaged screws to restore proper fit and alignment.

Secures and protects wiring harness from strain damage. Replace if cracked, broken, or wires show wear. Verify fit with your model number listed.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Replacement mounting screw secures panels, brackets, and trim inside refrigerators and freezers. Restores factory assembly when original fasteners are missing.

Positions the condenser fan and motor in the rear machine compartment. Replace if cracked, warped, or damaged to restore proper airflow direction.

Refrigerator not cooling or making loud grinding noise? The condenser fan motor drives airflow to cool refrigerant. DIY repair in 30-60 minutes.

Refrigerator not cooling properly? A damaged condenser fan blade prevents airflow over the condenser coils. Quick DIY fix—simply push into place.

Secures the evaporator or condenser fan shroud to the refrigerator cabinet. Replace this mounting screw if stripped, missing, or broken during repair.

Supports refrigerator crisper or bin drawers for smooth gliding. Replace when drawers stick or bind. Confirm fit with your model number listed.

Metal rivet fastener permanently secures panels, brackets, and internal components in refrigerators. Replace damaged, missing, or worn rivets to restore fit.

Channels defrost water from the evaporator to the rear drain pan. Replace this tube if it's cracked, clogged, missing, or has become brittle over time.

Positions and secures condenser tubing to maintain proper spacing. Replace if worn, broken, or missing to prevent vibration, rattling, and tube damage.

Water leaking from tubing connections or no water to dispenser? This tube connector joins refrigerator water lines to restore secure flow to your icemaker.

Refrigerator not cooling or freezer warming up? The heat exchanger manages refrigerant flow in the sealed system. Professional installation recommended.

Foam seal tape creates airtight barriers around refrigerator components. Replace when worn, compressed, or damaged to restore proper sealing and efficiency.

Connects dispenser controls and components in the refrigerator door. Replace if the wiring is damaged, frayed, or causing intermittent dispenser operation.

Secures refrigerator grille or trim to cabinet, preventing rattles and gaps. Replace when broken or missing to restore proper panel alignment. Verify fit with your model number before ordering.

Refrigerator not cooling or lights flickering? This electrical wiring harness restores power connections between components. Moderate DIY repair in 1-2 hours.

Replacement mounting screw for refrigerator panels, handles, brackets, and internal fixtures. Order when original screws are stripped, lost, or damaged.