Need Help?
Call
This is a door hinge for a range oven that connects the door to the oven frame, allowing it to open, close, and lock in place during the self-clean cycle. It uses a spring-loaded mechanism to hold the door at various open positions. Replace this hinge if the oven door drops down, won't stay open, closes unevenly, or is difficult to remove and reinstall.
Replace the hinges Read more
Metal rivet fastener permanently secures panels, brackets, and internal components in refrigerators. Replace damaged, missing, or worn rivets to restore fit.
Replaced rollers. Read more
Authentic freezer basket bumper that attaches to baskets to prevent sliding inside the freezer. Replace if broken, cracked, or missing to keep baskets stable.
Control box wiring harness assembly for refrigerators. Connects control board to components. Replace if wires are damaged, connector is cracked, or harness is worn.
Secures components inside your range or oven. Replace this bracket if it's bent, broken, or missing to restore proper mounting, alignment, and stability.
Replacement roller for range drawer rails. Supports smooth drawer gliding along tracks. Replace when worn, cracked, or causing drawer binding or misalignment.
Ordered rollers for the rails and a new drawer with rollers. The drawer and its rollers came separately and not attached as shown in the picture. Once we got the rollers on the rails (had to remove rails from the stove in order to hammer the rollers for attaching) and the rollers on the drawer box we couldn't slide the drawer in past the rollers on the rails. Wound up taking the rollers off the drawer, pulling the stove out for access from the back. Reinserted the drawer and then reattached the... Read more
This is a small metal or plastic retainer clip that secures the main top panel of the dryer to the cabinet frame. It holds the top panel firmly in place so it doesn't shift or rattle during operation. If your dryer's top panel feels loose, pops up during use, or won't stay properly seated, this clip may be broken or missing.
Replacement machine screw used to secure appliance panels and internal components, restoring a stable fit and reducing rattling. Matches a 10-32 thread with a 17/32-inch length for original fastener locations. What it does:
I got online and researched what might be the possible cause of that problem with my Frigidaire countertop range. This model is probably 15 years old, but I was able to locate what appeared to be the cause of my problem, a broken switch. I found Appliance Parts Pros online and was able to identify the part that I needed. I was also helped by a conversation with a young lady who helped me identify the exact part for my model range. I ordered the part and it arrived in less than a week. I watched... Read more
Restores the finished edge on your refrigerator cabinet and hides gaps. Replaces cracked, broken, or missing corner trim for a cleaner appearance.
I just snapped it on. Read more
If your oven won't turn on or takes several minutes to light, the igniter is likely failing. This flat Norton style igniter typically takes 30 minutes to replace.
The hardest part was getting the gas valve to turn. An old all metal one from the 1950s located in a narrow space that usually holds a drawer. Finally got it to turn using a crescent wrench on the metal part that turns and a pipe wrench to hold the valve still. Then it was smooth sailing except for stripping the wires on the short bit attached to the oven. Had no desire to pull the oven out of the wall, so made it happen. Turned the gas and power back on and presto the oven lights again. The... Read more
Burner won't light, stays on, or flame is uneven? This top burner valve controls gas flow to restore safe on/off control. Typical repair time: 45 minutes.
Ordered a new valve from you which was shipped the same day and arrived two days later,With excellent tracking. Had a little trouble installing it. However, I called , talked to your service rep who emailed me a service manual and even told me what page to look on. It can't get much better than that. Read more
Size: 6-20 x 0.312 inch.
Fixed rollers with leveling screw for the left hand side. For right side, order part 241889001.
Gas burner won't light or clicks but doesn't ignite? Replace the igniter switch to restore spark and reliable lighting. Simple 15-30 minute DIY fix.
Very simple repair. Watched video and followed each step. Took about 15 min to make repair. Read more
Replacement mounting screw for electric and gas ranges. Secures panels, brackets, trim, and oven base plates. Replaces missing, stripped, or corroded fasteners.
I replaced the screws and the missing spacers. It only took a few minutes once I had the new parts. Thank you for the fast response. Read more
Replace a cracked, broken, or missing outer housing cover on your range. This trim piece protects internal components and restores the finished look.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.