Tappan Range Parts

Replace a cracked, broken, or missing oven door spacer that maintains proper alignment and gap between door components. Installs in door assembly.

Supports and controls oven door movement on gas and electric ranges. Replace if hinge is broken, cracked, or spring mechanism has failed causing door sag.

This kit includes a wiring receptacle and harness that connects a surface burner element to the range's electrical system. The receptacle plugs into the terminal ends of the heating element and routes power from the control switch. Replace this kit if the receptacle is burned, melted, or corroded, or if a surface burner heats intermittently or fails to heat at all.

The bake element is the lower oven heating element that produces heat during bake cycles. Replacing a failed element restores proper preheating and even baking performance when your range no longer heats correctly in bake mode.

• Provides bottom-up heat in bake mode to reach and maintain set temperatures
• Typical symptoms include no heat in bake, excessively long preheat, or uneven/undercooked results
• Visual clues of failure may include blisters, cracks, or burnt spots on the element
• A shorted element may trip a household breaker when energized

• Disconnect power at the breaker before servicing; verify no power to the range
• Remove oven racks; unfasten the element from the rear wall and gently pull it forward to access terminals
• Transfer the wires to the new element one at a time; do not let wires retract into the rear panel
• Reinstall and secure the element, ensure connections are fully seated and clear of metal, restore power, and test

This gas supply tube routes fuel from the valve/manifold to a burner in your gas cooking appliance. A sound tube helps deliver a steady flame and safer, reliable operation by maintaining a sealed path to the burner.

• Directs gas from the control valve/regulator to the designated burner
• Maintains a sealed pathway to help prevent leaks
• Supports proper ignition and consistent flame size on the affected burner
• Common signs of a problem: gas odor near the tube, visible kinks/corrosion, hissing, or weak/no flame

• Disconnect power and shut off the gas supply; allow the appliance to cool
• Work in a well-ventilated area; support fittings with two wrenches to avoid stressing the valve/manifold
• Route the new tube exactly like the original; start threads by hand and tighten securely without over-torquing
• After reassembly, restore gas and check all joints with an approved leak-detection solution.

Main top support rod for electric ranges. Replacement needed when original rod is broken, bent, or damaged. Installs to provide structural support.

Secures the gas burner assembly to the cooktop base. Replace stripped, rusted, or missing screws to eliminate burner wobble and maintain proper alignment.

Replace your gas range's broken or missing control knob. This shaft-style knob installs on the control panel to adjust burner heat and oven settings.

Burner tube for gas ranges. Connects gas valve to burner assembly. Replace if cracked, corroded, or leaking to restore proper gas flow to cooktop burners.

Drawer slide glide for electric and gas ranges. Replace if cracked, broken, or worn to restore smooth, aligned drawer movement and eliminate sticking.

Range oven not heating? Safety valve controls gas flow to burners. Requires voltage testing at igniter connection. Moderate difficulty repair.

This is the hinge receptacle that secures the oven door hinge to the range frame, allowing the door to pivot open and closed smoothly. It acts as the mounting socket where the hinge arm locks into place. Replace this part if the oven door is sagging, not closing evenly, or if the hinge feels loose or disconnected from the frame.

Secures components inside your range or oven. Replace this bracket if it's bent, broken, or missing to restore proper mounting, alignment, and stability.

This is a door hinge for a range oven that connects the door to the oven frame, allowing it to open, close, and lock in place during the self-clean cycle. It uses a spring-loaded mechanism to hold the door at various open positions. Replace this hinge if the oven door drops down, won't stay open, closes unevenly, or is difficult to remove and reinstall.

Replacement roller for range drawer rails. Supports smooth drawer gliding along tracks. Replace when worn, cracked, or causing drawer binding or misalignment.

This is a small metal or plastic retainer clip that secures the main top panel of the dryer to the cabinet frame. It holds the top panel firmly in place so it doesn't shift or rattle during operation. If your dryer's top panel feels loose, pops up during use, or won't stay properly seated, this clip may be broken or missing.