Need Help?
Call or text
Oven won't light even with glowing igniter? Safety valve controls gas flow to burner. Moderately easy repair with gas line disconnect required.
My tenant thought that the oven safety valve was bad, but after some research, I found that the transfer of heat from the igniter had to be sufficient enough to cause the valve to open.Your agent confirmed this and reassured me that even if the igniter was glowing, there was a 99% chance that it wasn't getting hot enough. I ordered the igniter, and also the safety valve just in case, as we were going to be fixing this on Christmas eve, so the oven could be used for Christmas dinner. Your agent... Read more
Burner won't light or flame is weak? This gas valve controls flow to your range surface burner for reliable ignition and heat control. Moderate DIY.
Replaced the old valve with a new one from AppliancePartsPros.com. I watched one of the YouTube videos to get an idea of what the process would entail. I gathered the tools I would require, plus a work light. The repair/replacement went pretty good. One thing the video I watched didn't cover was adjusting the valve for a propane system. I compared my old valve to the new one and saw that I would have to screw down the oven gas outlet until it "bottomed out". Read more
Replace a gas range burner valve that's broken, stuck open, or causing hard-to-adjust flames. Moderate DIY repair requires raising the stovetop.
After turning off the gas and unplugging the electricity, I removed all the burners from the stove top using a 3/16" hex socket. Then used a 1/4" socket to removed two or three screws under each burner which hold the burner base to the bottom of the top panel. Then pulled all the knobs and removed the front panel which was held in by two Phillips screws accessible from underneath the panel. It helps to open the oven door to get at these screws. With the knob panel gone, I removed two screws... Read more
Oven won't light even though igniter glows? Burner lights only when valve is tapped? Replace the dual gas safety valve. DIY install in under 1 hour.
From the Appliance Parts website I watched a 3 minute Youtube video. The video actually explained the process on another range but it was enough information for me to do the project myself. The part came 2nd day UPS and I installed it in under an hour. The only hitch was that I didn't see the note (maybe it wasn't there) that explained how the valve is set for Natural gas and that for LP gas I'd need to adjust the jet that goes into the burner tube. Maybe that was on the video. Read more
If your oven won't ignite but the igniter glows red-hot, a faulty safety valve may be blocking gas flow. This valve regulates gas to restore ignition.
Found the problem through troubleshooting. Looked up the part on appliance parts pro. It was at my doorstep in 2 days. Replaced old gas safety valve. Oven works great again. Read more
Burner won't light or flame height won't adjust? This top burner valve controls gas flow to restore reliable ignition and precise flame control.
Range oven not heating? Safety valve controls gas flow to burners. Requires voltage testing at igniter connection. Moderate difficulty repair.
Replaced the safety valve. Read more
Burner won't light, stays on, or flame is uneven? This top burner valve controls gas flow to restore safe on/off control. Typical repair time: 45 minutes.
Ordered a new valve from you which was shipped the same day and arrived two days later,With excellent tracking. Had a little trouble installing it. However, I called , talked to your service rep who emailed me a service manual and even told me what page to look on. It can't get much better than that. Read more
Burner won't light or heat unevenly? This top burner valve regulates gas flow to restore proper flame control. Moderate DIY repair in under an hour.
Burner won't light or flame is uneven? This top burner valve controls gas flow to surface burners. Moderately easy repair restores proper flame control.
If your range burner won't ignite, stay lit, or adjust flame properly, the top burner valve may need replacement. Restores precise heat control.
Burner won't light or heat properly? This top burner valve controls gas flow to restore proper flame adjustment. Direct-fit part for gas ranges.
If your range burner won't ignite, stays on high, or has uneven flames, the top burner valve may be faulty. This valve controls gas flow to each burner.
Usually ships within 4 - 14 days
Fix a burner that won't light, won't adjust, or stays on with this range top burner valve. Controls gas flow to surface burners. Moderate DIY repair.
Range won't heat or shuts off unexpectedly? This safety valve controls gas flow and prevents overheating. Restores proper temperature control and safety.