Tappan Screws, Nuts, Washers

Specs: Hex head ,1/4-20 x 5/8

This replacement screw secures appliance components so panels, brackets, and trim stay tight and properly aligned. Replace a missing, stripped, or corroded fastener to restore a solid fit and help stop vibration or rattling.

• Fastens components to the chassis or assembly for correct fit
• Helps maintain alignment and reduce movement and noise during operation
• Restores secure mounting when original hardware is missing, rusted, or stripped
• Typical symptoms: loose panel or handle, rattling noises, hardware backing out

• Disconnect power; if servicing a dishwasher, also shut off water
• Match the screw to the original location before installation
• Start threads by hand to avoid cross-threading, then tighten snugly without overtightening

Black

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This is the screw used to secure the dishwasher spray arm assembly components together, helping keep the arm properly attached so it can rotate and distribute wash water effectively.

• Fastens the spray arm assembly components to prevent wobble or detachment
• A loose or missing screw can cause poor cleaning, noisy operation, or a spray arm that falls off
• Restores stable spray arm rotation and consistent wash coverage

• Disconnect power and shut off water before servicing
• Open the dishwasher, remove the lower rack, and support the spray arm to prevent damage
• Use the correct screwdriver and avoid overtightening to protect plastic parts
• Check spray arm for free rotation after installation

This factory screw fastens refrigerator components and panels. It replaces missing or damaged hardware so parts stay aligned and secure, reducing looseness and rattles caused by vibration. What it does:

• Secures panels, brackets, and trim per your model's design
• Helps maintain alignment and reduce vibration-related loosening or noise
• Replaces missing, stripped, or corroded hardware
• Restores a snug fit when threads or heads are worn

• One screw

• Disconnect power; turn off the water supply if working near ice or dispenser systems
• Use the correct driver; start threading by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking adjacent plastic
• Refer to your model's diagram to confirm location and quantity used

This burner mounting screw fastens the surface burner assembly to its base on the cooktop, keeping it stable and properly aligned. Replace stripped, rusted, or missing screws to eliminate wobble and maintain even flame positioning.

• Secures the surface burner to the orifice holder/cooktop assembly
• Helps keep the burner level, stable, and properly seated
• Can address a loose or wobbly burner or one that lifts when removing the grate/cap
• Restores proper seating when original hardware is lost or corroded

• Disconnect power and shut off the gas supply; allow the cooktop to cool completely
• Remove grate, cap, and burner head (as designed) to access the fastener
• Start threads by hand and use the correct driver to avoid cross-threading
• Tighten snugly without overtightening; clean or chase threads if corrosion is present

Replacement screw that secures panels, trim and internal components in compatible appliances. Restores proper fit and helps reduce rattling or loose parts when the original fastener is missing, worn, or damaged. What it does:

• Fastens panels, brackets, trim pieces and small component assemblies to the appliance frame
• Helps eliminate noise and vibration caused by loose or missing fasteners
• Replaces stripped, corroded or missing screws to restore secure mounting
• Matches OEM fit when the identical screw is required for proper alignment

• Disconnect power to the appliance before starting any repair
• Use the correct driver size to avoid cam-out or damage to the screw head
• Do not overtighten; overtightening can strip threads or crack plastic parts

This replacement screw secures appliance panels and internal components so they stay aligned and rattle-free. Replace missing or stripped hardware to restore a tight, reliable fit and prevent looseness that can lead to noise or damage.

• Fastens panels, brackets, or components to the chassis as designed
• Helps reduce vibration, rattling, and gaps from loose or missing hardware
• Restores proper alignment when an original screw is lost or threads are damaged
• Maintains safe, secure mounting of the original assembly

• Disconnect power (and shut off gas/water if applicable) before servicing
• Replace in the same location and orientation as the original hardware
• Hand-start threads to avoid cross-threading; tighten snugly without overtightening
• Transfer any original washer or clip if present

Replacement machine screw used to secure appliance panels and internal components, restoring a stable fit and reducing rattling. Matches a 10-32 thread with a 17/32-inch length for original fastener locations. What it does:

• Fastens panels, trim pieces, and internal brackets; a missing or damaged screw can cause loose panels or rattling noises.
• Secures knobs, control housings and small assemblies to prevent wobble or misalignment.
• Restores proper fit for components so doors and access panels sit evenly and function reliably.

• Disconnect power (unplug or shut off circuit) before accessing components.
• Use the correct driver and tighten by hand; avoid overtightening to prevent stripped threads or cracked plastic.
• Keep any original washers or clips and reinstall them with the screw.

This rivet is a metal fastener used to permanently secure panels, brackets, or internal components in your appliance. Replacing a damaged or missing rivet restores a tight fit and helps prevent vibration, rattles, and looseness.

• Permanently joins thin metal parts where screws or nuts aren't used
• Maintains alignment and structural integrity of housings and frames
• Helpful when panels or components are loose, rattling, or won't stay secured
• Direct replacement for a worn, broken, corroded, or drilled-out factory rivet

• Disconnect power and shut off gas/water (as applicable) before servicing
• Support the part being fastened; drill out the old rivet head if needed
• A hand riveter/rivet tool may be required to set the new rivet
• Wear eye and hand protection during drilling/riveting

This replacement screw secures dishwasher components so they stay tight and aligned during operation. Use it to replace missing, rusted, or stripped hardware and restore a solid, rattle-free installation. What it does:

• Fastens compatible parts to the tub, frame, or internal assemblies
• Replaces worn or damaged screws to maintain proper mounting
• Helps reduce rattling or vibration from loose hardware
• Prevents shifting that can affect wash performance or cause leaks, depending on location

• 1 screw

• Disconnect power and shut off water before servicing
• Access the component being secured and remove the damaged or missing screw
• Start threads by hand to avoid cross-threading; do not overtighten, especially into plastic
• Match length and style to the original fastener for correct fit

This #8-32 x 3/8 screw secures appliance panels, brackets, and assemblies. Replace a missing or stripped fastener to keep parts tight and aligned, reduce vibration, and restore proper fit in compatible refrigerators and freezers.

• Machine-thread fastener sized #8-32, 3/8-inch length
• Secures control housings, trims, covers, and support brackets per model design
• Replaces missing, worn, or corroded screws that cause loose or rattling parts
• Helps maintain alignment and stability after service

• Unplug the appliance; shut off water if applicable
• Match thread size to the original and start by hand to avoid cross-threading
• Use the correct driver; do not overtighten, especially into plastic
• Verify component alignment and operation after fastening

• Thread size: #8-32
• Length: 3/8 inch

This factory screw secures panels, brackets, and trim in your appliance. Replacing a missing, stripped, or corroded fastener restores solid mounting, reduces rattles, and helps keep doors, controls, and panels aligned as intended. What it does:

• Fastens appliance components in their proper position
• Commonly used to secure panels, trim, or brackets depending on model
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Symptoms can include loose or vibrating panels, misaligned trim, or rattling noises during operation

• Includes 1 screw

• Disconnect power; if applicable, shut off gas and allow all surfaces to cool before servicing
• Match location to the original screw and replace one at a time to maintain alignment
• Start threads by hand to avoid cross-threading; do not overtighten
• Use the correct driver/bit to prevent damaging the screw head

This replacement latch mounting screw secures the refrigerator door latch assembly so the door closes and seals properly. Installing a fresh mounting screw restores a solid latch connection and reduces door movement or rattling. What it does:

• Fastens the door latch assembly to the cabinet or door frame
• Keeps the latch aligned so the door closes and seals correctly
• Prevents loose or wobbly latch hardware and related rattling noises
• Helps address symptoms like a door that won't stay latched or minor door play

• Turn off power to the appliance or unplug before working near electrical components
• Use the correct screwdriver and thread the screw straight to avoid stripping
• Do not overtighten — snug is sufficient to hold the latch without deforming parts
• Test the door operation after installation

Size: 6-20 x 0.312 inch.