Thermador Range Parts

Replaces the interior glass pane in your oven door assembly. Needed when the original inner glass is cracked, shattered, or broken. Restores visibility.

This replacement roller fits the front or rear position of a slide mechanism, restoring smooth, even movement and reducing noise when a wheel is worn or broken. It helps racks or drawers glide properly and stay aligned. What it does:

• Provides low-friction rolling support for the slide track
• Helps slide-out assemblies move freely without binding or scraping
• Worn or damaged rollers can cause sticking, squeaking, or uneven travel
• Restores proper alignment and smooth operation when replaced

• 1 roller assembly

• Disconnect power and allow the appliance to cool before servicing
• Remove the slide-out assembly; note roller orientation and hardware
• Transfer/reuse existing screws, clips, or retainers as required
• Do not lubricate unless the manufacturer specifies a lubricant

This high-limit thermostat is a safety device that monitors the oven's internal temperature and cuts power to the heating element if the temperature exceeds a safe threshold. It helps prevent overheating and potential fire hazards. Replace this part if your oven shuts off unexpectedly, fails to heat at all, or triggers error codes related to excessive temperature.

Replacement housing cover for microwaves and ovens. Closes and protects internal openings. Restores secure fit when original is cracked, missing, or warped.

Replacement drip pan for gas cooktops and ranges. Sits beneath burners to catch spills and protect the cooktop base. Replace if cracked, warped, or rusted.

This OEM replacement part is a motor assembly for ovens. The motor assembly is the main motor that powers the oven fan which is responsible for maintaining and adjusting the temperature in an oven. If the oven is no longer heating properly, turning on, or maintaining temperature, then the motor assembly will need to be replaced.To replace this part, make sure that the oven is unplugged. After it has been powered off, proceed to pull the oven out and away from the wall. Once moved, uninstall the back panel of the oven by removing the panel's mounting screws. After detaching the back panel, locate the motor housing on the back of the oven. Unthread the screws that hold the housing in place. Once removed, locate the mounting brackets that hold the motor in place and remove the screws that attach to the motor. Pull the old motor out of its place and install the new motor. Reinstall the back panel and restore power to the appliance.This genuine replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador brand ovens.

The Jet Holder with Nut is an OEM part for Bosch ranges and cooktops. It holds precisely machined jets that control gas flow from each burner valve.

Causes may be wear and deterioration from prolonged heating exposure. Physical impacts or damage accumulation over time could also compromise the jet holder.

Symptoms of a bad jet holder can include:

• Inability to adjust or maintain proper flame stability and heat output
• Irregular or uneven flame patterns between surface burners
• Potential gas leaks observed at jet connections

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This pilot light lens covers and diffuses the control-panel indicator lamp. Replace a cracked, missing, or discolored lens to restore clear visibility of the light, protect the lamp opening, and keep the panel looking finished.

• Covers and diffuses the indicator lamp on the control panel
• Helps protect the lamp opening from debris and accidental contact
• Restores a clean, finished appearance to the panel
• Replace if the lens is cracked, missing, loose, or discolored
• Can help when the indicator is hard to see even when lit

• Disconnect power to the appliance before servicing and allow surfaces to cool
• Access the indicator opening from the front or rear (varies by design) and remove any retainer or clips holding the old lens
• Note orientation and transfer any existing retainer or gasket if present
• Seat the new lens fully, reassemble, and test the indicator light

If your oven won't start or runs with the door open, this door interlock switch detects proper closure and latching. DIY repair in under an hour.

This rotary potentiometer converts shaft rotation into an electrical signal the control board can read, providing precise position feedback for user selections. Replace it if inputs become erratic, jump between settings, or the control stops responding.

• Provides rotary position feedback to the electronic control
• Enables accurate selection and adjustment of functions or setpoints
• Wear or damage can cause drifting, dead spots, or incorrect readings
• Intermittent or no response to input is a common failure symptom

• Disconnect power before servicing
• Access the control/console area to reach the component
• Note shaft orientation and any connector positions; transfer exactly to the new part
• Handle electronics with ESD care and verify smooth, full-range operation after reassembly

Fixes no spark at burners or oven not lighting issues. This ignition module generates the high-voltage spark needed to ignite gas at electrodes.

Restore reliable baking performance with this bake heating element. Mounted at the bottom of the oven, it provides the primary heat source in Bake mode so the cavity reaches and maintains the set temperature for consistent results. What it does:

• Heats the oven in Bake mode to reach and hold the set temperature
• Failure can cause no heat in bake, very slow preheating, or uneven/undercooked results
• Visible cracks, blisters, or a broken coil indicate the element should be replaced
• A shorted element may trip a household breaker or blow a fuse

• One bake heating element

• Disconnect power at the breaker and allow the oven to cool before servicing
• Remove oven racks; take out the element's mounting screws and gently pull the element forward to access wire terminals
• Transfer wires one at a time to the new element; do not allow wires to fall back into the insulation
• Reinstall the element and panels, restore power, and test bake operation

Replacement foot assembly for gas cooktop or range grates. Installs on the underside to cushion contact and stabilize the grate. Replace when worn, missing, or broken.

This is an 8-inch coil-style surface heating element that plugs into a burner receptacle on the cooktop of your range. It provides radiant heat for cooking on the stovetop. Replace this element if the burner doesn't heat up, heats unevenly, produces visible damage such as pitting or blistering, or fails to glow red when turned on.

Oven slow to heat or not reaching set temperature? This bake heating element restores proper heating. Straightforward DIY repair that can save $500+.

Replacement selector knob for your range. Fits onto the control shaft to select functions, cycles, or heat levels. Needed when original is cracked, broken, or missing.