Thermador Range Parts

Burner won't light or clicks continuously? This spark ignition module generates the voltage needed to ignite gas burners. Moderate DIY repair.

Electrode that produces the ignition spark for gas ovens and ranges, restoring reliable burner lighting. Replace a damaged or worn electrode to stop repeated clicking, weak sparks, or burners that fail to light. What it does:

• Delivers the spark at the burner to ignite gas during startup.
• Common symptom fix: oven/range burners that won't light or that click continuously without producing a flame.
• Use when the electrode is cracked, corroded, or the ceramic insulator is damaged.
• Works as part of the appliance's ignition system alongside the spark module/igniter wiring.

• Turn off power and gas supply before beginning any service.
• Avoid touching or chipping the ceramic insulator; handle the tip carefully.
• Reconnect wiring exactly as removed and secure the electrode in the original orientation.

Support, hinge counter restores proper hinge support and door balance for a worn or damaged hinge assembly. This replacement helps the appliance door open and close smoothly and stay aligned for reliable everyday use. What it does:

• Provides structural support to the door hinge and helps counterbalance the door
• Stabilizes hinge movement to reduce sagging, binding, or uneven closing
• Helps the door latch and seal correctly by keeping the hinge alignment consistent
• Use when you notice door droop, difficulty latching, or irregular door motion

• Installation may require partial disassembly of the door or hinge assembly—refer to the OEM instructions for your model
• Disconnect power and turn off water supply before beginning any repair
• Inspect surrounding hinge components and fasteners; replace any damaged parts and test door operation after installation

The Surface Element is an OEM part for Bosch cooktop and ranges. Measuring 6 inches across, it provides focused heat from below for smaller sized cookware.

Causes of a bad 6" plug-in element generally relate to normal wear and tear over time. Spills left on the coils could potentially cause issues by corroding internal wiring or damaging heating components.

Symptoms of a bad narrow surface element can include:

• The element heating intermittently or not at all
• Only parts of the coil visibly heating up
• Buzzing or clicking coming from below the element
• Tripped circuit breakers affecting that specific element

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This is a thermal fuse designed to protect the microwave's electrical circuit from overheating. It acts as a safety device that breaks the circuit if internal temperatures exceed safe limits. Replace this fuse if your microwave suddenly stops working or loses all power, as a blown thermal fuse is a common cause of a completely dead unit.

Incandescent oven light bulb restores interior illumination so you can monitor cooking without opening the door. Replace when dim or burned out.

Jet holder assembly routes gas through the orifice to the burner. Replace if cracked, corroded, or stripped threads prevent secure installation.

Pressure regulator for gas cooktops maintains consistent gas flow to burners. Replace if leaking gas odor, damaged vent, or worn seals detected.

This metal heat deflector mounts inside the range to redirect heat and protect surrounding components from excessive temperatures during cooking. It acts as a shield to guide hot air away from sensitive areas such as controls or adjacent cabinetry. Replace this part if it is warped, corroded, or cracked, which can lead to uneven heat distribution or damage to nearby parts.

Replace a worn, broken, or missing gas range control knob. Restores safe operation and improves appearance. Fits directly onto the control shaft.

Rounded cap that sits over your gas cooktop burner to contain and direct flames. Replace if cracked, chipped, warped, or worn from high heat exposure.

Black burner cap assembly that covers and protects the gas burner head. Replace if your cap is cracked, chipped, damaged, or missing to restore appearance.

This air interlock is the airflow switch that helps monitor and control dryer vent airflow, ensuring the appliance only runs when proper air movement is detected. It replaces a worn or failed interlock to restore normal vent sensing. What it does:

• Senses airflow through the vent and signals the control system to allow or stop operation
• Prevents dryer from starting or continuing a cycle when airflow is restricted
• Common symptom: dryer fails to start, stops mid-cycle, or shows poor drying performance
• Can help address intermittent operation caused by a faulty vent sensing switch

• Disconnect power before servicing to avoid electrical shock
• Handle the switch and wiring gently; verify connector orientation before reinstalling
• Confirm venting is clear and intact when replacing this part

Secures internal components to the range frame. Replace if bracket is cracked, broken, bent, or missing to restore proper alignment and stability.

This burner base supports the cooktop's burner cap and directs flame for even heating. It replaces a damaged or warped base to restore stable burner alignment and consistent flame pattern. What it does:

• Holds the burner cap in place and centers the gas flame
• Channels gas flow for proper burner operation
• Helps prevent wobbling or uneven heating from a warped base
• Commonly replaced when the base is cracked, corroded, or bent

• One burner base (B)

• Turn off gas supply and power to the appliance before servicing
• Remove surrounding burner components and reassemble in reverse order
• Inspect nearby seals and burner ports for damage; replace if necessary

Oven not heating or baking unevenly? This lower bake element restores consistent heat for even cooking. DIY-friendly repair in under 30 minutes.