Thermador Range Parts

This is a replacement glass panel for the appliance's front panel. It restores a clean, durable surface and helps protect the components behind it when the original glass is cracked, chipped, or shattered.

• Forms the exterior glass surface on the appliance's front panel
• Helps shield underlying components from spills and impacts
• Restores proper fit and appearance when the original glass is damaged
• Common symptoms: visible cracks/chips, shattered glass, loose or rattling panel, missing glass

• Disconnect power; also shut off gas before servicing
• Wear cut-resistant gloves and eye protection; handle glass carefully
• Support the door or front panel during removal to prevent stress or drops
• Transfer and reuse existing trim, logos, gaskets, and hardware as designed; do not overtighten fasteners

This spark igniter is the burner electrode that creates the high-voltage spark to light the gas. Replacing a worn igniter restores quick, reliable ignition and helps eliminate repeated clicking or having to light the burner manually.

• Generates a spark at the burner to ignite gas during lighting
• Typical symptoms: burner won't light, no visible spark at that burner, intermittent or delayed ignition, or needing a match to light
• Replaces a cracked, fouled, or heat-damaged electrode that no longer sparks reliably
• Provides the ignition spark only; gas flow is managed by the valve

• Disconnect power and shut off gas before servicing
• Remove grates/caps and access the burner; note wire routing and mounting
• Transfer mounting hardware from the old igniter; handle the ceramic insulator gently and keep the tip clean
• Reassemble, restore power/gas, and verify proper spark and burner ignition

This potentiometer is the rotary sensor behind the control knob. It converts knob rotation into an electrical signal the control board uses to adjust settings, restoring smooth, accurate response when a worn or erratic control causes inconsistent operation.

• Translates knob rotation into a variable-resistance signal for the electronic control
• Enables the control board to regulate power/heat or speed, depending on model
• Common failure symptoms: unresponsive or jumpy settings, dead spots when turning, or settings that drift
• Helps restore precise, repeatable adjustments at the knob

• Disconnect power to the appliance before servicing
• Pull off the knob and open the control panel to access the potentiometer
• Move wires one at a time to the new part; align the shaft/flat to the knob as noted
• Reassemble and test full range of adjustment; follow any model-specific calibration if required

This replacement jet holder fits the 15,000 burner on gas cooktops and ranges. It supports the orifice and channels gas to the burner head, helping restore a stable flame and consistent heat when the original holder is damaged or corroded.

• Positions and secures the orifice for the 15,000 burner
• Routes gas from the valve/manifold to the burner head
• Helps maintain proper flame shape and output
• Replace if cracked, warped, or corroded; symptoms can include weak or uneven flame, yellowing, or difficulty lighting at that burner

• Shut off gas supply and disconnect power before servicing
• Remove grates, burner caps, and heads; raise or remove the cooktop surface to access the holder
• This holder is specific to the 15,000 burner position; transfer the orifice and any seals as required
• After reassembly, check all gas connections for leaks with a soap-and-water solution and verify burner operation

This OEM part is a power control board. The power control board provides power to the electronic oven control board. If the oven is no longer turning on, or the digital display is no longer visible, this could mean it's time to replace the power control board. Luckily this is a relatively simple process.To begin, make sure to turn off the power to the oven by unplugging it or shutting off the circuit breaker. Then proceed to remove the upper back panel. Once removed locate the power control board and remove the wire harness and wires attached to it. Be sure to take note of the orientation of the wires to place them into the correct terminals on the new board. Attach the wires to the new board and snap the new board back in place. Resecure the back panel and put the oven back in place.This genuine replacement part is sold individually and is compatible with Bosch, Thermador, and Gaggenau ovens.

This condenser fan blade mounts to the fan motor and pulls air across the condenser coil and compressor. Replacing a cracked or warped blade restores airflow so your refrigerator cools efficiently and the compressor runs at a safe temperature.

• Circulates air through the condenser coil and over the compressor to remove heat
• Helps maintain cooling performance and stable system pressures
• Common symptoms: weak or no airflow at the rear/base, rattling or scraping noises, wobble/vibration, visible cracks or missing fins, warmer-than-normal compartments or hot cabinet sides
• Works with the condenser fan motor and shroud; typically replaced when the hub is stripped or the blade is damaged

• Disconnect power and pull the refrigerator out; remove the rear access cover near the compressor
• Note blade orientation and depth on the motor shaft before removal
• Pull the old blade straight off; press the new blade onto the shaft until fully seated and ensure it spins freely with proper shroud clearance
• Reinstall the cover, restore power, and verify strong, quiet airflow

Color: metallic. Measures about 13-1/2 inches wide by 5 inches high.

The Grease Filter is an OEM part for Bosch ranges and cooktops. It is responsible for capturing and containing grease, oils, and other vapors produced from cooking to help keep indoor air fresh and prevent buildup. Regular cleaning is important to maintain optimal performance.

Causes of a bad grease filter can include excess buildup that blocks airflow from frequent high-heat cooking. Exposure to flames or excessive heat may cause damage over time as well.

Symptoms of a bad grease filter include:

• Reduced suction power and airflow from the range hood
• Grease accumulation on surrounding surfaces below the hood
• Unpleasant cooking odors escaping into the kitchen rather than being vented outside

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This Venturi is an OEM part for Bosch Ranges. It plays a role in supplying air to the burner for proper combustion. Continuous exposure to heat and debris can cause this part to degrade or malfunction.

What Causes a Bad Venturi: 
Exposure to heat and debris from cooking can cause the venturi to deteriorate over time. Blockages or clogs in the venturi can also affect its functionality.

Symptoms of a Bad Venturi:

• Uneven flame or inconsistent burner operation
• Reduced gas flow to the burner
• Burner flame discoloration

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Burner Head and Cap Assembly is an OEM part for Bosch ranges and cooktops. It contains the burner itself along with its protective cover.

Cracks or misshapen portions disrupt flame stability leading to inconsistent results.

Symptoms of a failed assembly include:

• Irregular or overly high flames from damage exposing gas jets
• Difficulty igniting or flames extinguishing prematurely
• Singed pans lacking the protection of an intact cap

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Replacement bake element for the oven that restores heating for even baking and proper temperature performance. Installs in the oven cavity to provide the heat required during bake cycles. What it does:

• Heats the oven cavity during bake cycles so food cooks evenly.
• Common symptom: oven fails to reach set temperature or food is undercooked.
• Visible symptom: element that is blistered, broken, or shows burn marks may need replacement.
• Electrical symptom: an open (no continuity) element will prevent the oven from heating.

• Always disconnect power to the appliance at the breaker before starting work.
• Allow the oven to cool completely and wear gloves to protect against sharp edges.
• Access typically requires removing oven racks and the inner panel; disconnect wiring at the element terminals and secure the new element in place.
• Restore power and test the oven on a bake cycle after installation.

Knob, blk (cvs)

The Control Knob is an OEM part for Bosch ranges and cooktops. As the interface regulating gas flow, control knobs activate precise burner levels through internal calibration.

Causes of failure include loosened set screws beneath allowing knob slippage. Prolonged heat and moisture exposure may also degrade contact surfaces over time.

Symptoms of faulty knobs include:

• Burners failing to engage or not matching dial settings
• Inability to decrease output levels from full flame
• Knobs wobbling insecurely or detaching entirely

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Restore fast, even convection cooking with this rear convection heating element. It supplies a ring of heat around the fan at the back of the oven so temperatures rise and hold properly in convection bake and roast modes.

• Provides heat around the convection fan for uniform air circulation and even results
• Common symptoms: no heat or very slow preheat in convection modes
• Fan runs but temperature does not rise in convection
• Visible damage or a break in the element

• Disconnect power at the breaker or unplug the appliance; allow the oven to cool completely.
• Remove racks; access and remove the element's mounting screws from inside the oven (procedure varies by model).
• Pull the element forward carefully; label and transfer wires one at a time so they don't slip back into the cavity.
• Reuse existing hardware; ensure terminals are tight, reassemble, and test a convection cycle.

This gas pressure regulator controls and stabilizes incoming supply pressure to the appliance manifold, helping ensure consistent burner flames and reliable ignition. Replace if the original regulator is sticking or no longer maintaining correct pressure.

• Regulates incoming gas to the appliance's rated manifold pressure
• Helps maintain even flame height and proper combustion
• Supports reliable burner ignition and reduces flame-out from pressure swings
• Common symptoms include weak or uneven flames, yellow tipping, burners not lighting or not staying lit, or flames that are too high

• Disconnect electrical power and shut off the gas supply before servicing
• Observe the flow-direction arrow; install with outlet toward the appliance manifold
• Use approved gas-rated thread sealant on male threads only and leak-test all joints with a non-corrosive solution after installation

The Oven Door Gasket Kit is an OEM replacement part for 27" Bosch wall ovens. It includes a gasket for insulating the oven cavity while in use and clips to secure it. Over time, heat and compression can break down gasket material allowing potential leaks of hot air from the oven during cooking or difficulty closing the door. Causes involve standard wear from repetitive door closing as well as exposure to high oven temperatures over many heating cycles.

Symptoms of failed gaskets include: 

• excessive heat escape from the door opening
• Door locking difficulties
• visible cracks or tears in the gasket materials 

Replacing the gasket allows for smooth door movement and an tight seal when closed. This Bosch part can also be used on Thermador and Gaggenau appliances.

This bake element heats the small oven cavity from below during Bake, delivering the radiant heat needed for preheating and consistent baking when the original element fails.

• Provides primary bake heat at the bottom of the small oven cavity
• Works with the oven control to preheat and maintain set temperature
• Common failure symptoms: no or weak bake heat, uneven baking, visible blistering/cracks, or a breaker trip when Bake is selected

• Disconnect power at the breaker before servicing
• Access is typically from inside the cavity; remove mounting screws, pull the element forward, and move wires one at a time
• Support wires so they don't retract into the insulation; avoid bending or stressing the new element
• Restore power and run a bake cycle to verify proper heating

This OEM replacement part is a motor assembly for ovens. The motor assembly is the main motor that powers the oven fan which is responsible for maintaining and adjusting the temperature in an oven. If the oven is no longer heating properly, turning on, or maintaining temperature, then the motor assembly will need to be replaced.To replace this part, make sure that the oven is unplugged. After it has been powered off, proceed to pull the oven out and away from the wall. Once moved, uninstall the back panel of the oven by removing the panel's mounting screws. After detaching the back panel, locate the motor housing on the back of the oven. Unthread the screws that hold the housing in place. Once removed, locate the mounting brackets that hold the motor in place and remove the screws that attach to the motor. Pull the old motor out of its place and install the new motor. Reinstall the back panel and restore power to the appliance.This genuine replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador brand ovens.