Thermador Refrigerator Parts

The Ice Stripper Kit is an OEM part for Whirlpool refrigerators. This kit helps in the efficient removal of ice from the ice maker, ensuring smooth and continuous ice production.

Common causes include wear and tear from regular use, buildup of ice or debris, or damage from mishandling during maintenance.

Symptoms of a bad ice stripper kit include:

• Ice cubes not being properly ejected from the ice maker
• Ice jams or blockages
• Reduced ice production
• Unusual noises coming from the ice maker

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This icemaker fill cup and bearing assembly directs water from the inlet tube into the ice mold and provides the pivot point for the shutoff arm. Replacing a cracked or missing cup helps stop leaks, misdirected fills, and inconsistent ice production.

• Channels incoming water into the ice mold to prevent splashing and overfilling
• Provides the pivot/bearing for the ice level (shutoff) arm
• Helps maintain consistent cube size and reliable icemaker shutoff
• Typical symptoms: water or ice buildup under the icemaker, overfilling or hollow/irregular cubes, or a loose/binding shutoff arm

• Unplug the refrigerator and shut off the water supply before servicing
• Remove the ice bin and detach the icemaker to access the side-mounted cup
• Position the new cup directly under the fill tube; secure with existing hardware and verify the shutoff arm pivots freely in the bearing
• Restore power and water; run a test fill and check for leaks

The Defrost Thermostat is an OEM part for Whirlpool refrigerators. The thermostat monitors the temperature of the evaporator coil and signals the defrost heater to turn on or off to prevent frost buildup, ensuring efficient cooling.

Causes of a bad defrost thermostat can include wear and tear over time, exposure to extreme temperatures, or electrical malfunctions.  

Symptoms of a bad defrost thermostat include:

• Excessive frost buildup in the freezer
• The refrigerator not maintaining the correct temperature
• The defrost heater not activating
• The refrigerator running continuously or not running at all

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This magnetic refrigerator door gasket forms the airtight seal between the door and cabinet to keep cold air in and moisture out. Replacing a worn gasket restores a tight seal for stable temperatures and reliable performance.

• Creates a magnetized, airtight seal around the door perimeter to prevent air leaks
• Helps maintain set temperatures and reduce condensation or frost around the door
• Supports consistent cooling and overall efficiency
• Common symptoms of failure: gaps or warping, torn corners, door not closing securely, moisture or frost at the door edge

• Disconnect power before servicing
• Allow the gasket to warm and relax; use warm water or a hair dryer on low to soften—do not overheat
• Remove the old gasket from the retainer and press the new gasket in, starting at the corners and seating evenly around the perimeter
• Check door alignment and retighten/adjust hinges as needed; verify seal with a paper slip test

Color: chrome. Measures about 12-1/2 inches wide by 5 inches high.

The Bulb is an OEM part for Bosch ovens. This component provides illumination inside the oven, allowing you to easily monitor the cooking process without opening the door and losing heat.

Causes of a bad bulb can include filament burnout due to extended use, electrical issues that cause power surges, or physical damage from accidental impacts. 

Symptoms of a bad bulb include:

• The oven light not turning on
• Flickering light inside the oven
• Dim or uneven lighting
• The bulb appearing visibly damaged or burnt out

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This dual water inlet valve controls water flow to a refrigerator's ice maker and dispenser. Replacing a sticking or leaking valve restores proper filling and reliable dispensing while helping prevent drips, slow flow, or no ice.

• Directs household water to the ice maker and door dispenser through two independent outlets
• Opens and closes electronically via two solenoids when the control calls for water
• Common failure symptoms: no water from the dispenser, ice maker not filling, slow/weak flow, or leaks/drips at the valve
• Mineral buildup, cracks, or failed solenoids can prevent sealing or operation and warrant replacement

• Unplug the refrigerator and turn off the water supply before servicing
• Relieve line pressure and keep a towel or container ready for residual water
• Label and transfer tubing and wire connectors to the new valve one at a time to maintain orientation
• Restore water, check carefully for leaks, and purge air by running the dispenser

This refrigerator water filter housing holds the filter cartridge and routes water through the dispenser and ice system. Replacing a cracked or leaking housing restores proper sealing, water flow, and smooth, reliable filter changes.

• Secures the water filter and seals the inlet/outlet connections
• Channels water through the filter to the dispenser and ice maker
• Helps correct leaks around the filter area
• Common symptoms: low/no dispenser flow, ice maker not filling, filter won't seat or release

• Disconnect power and turn off the household water supply before servicing
• Dispense water to relieve line pressure; place a towel to catch residual water
• Access location varies by model; remove the grille or interior cover, then disconnect the water lines and mounting hardware from the old housing
• Install the new housing, ensure tubing is fully seated, restore water and power, check for leaks, and purge air by dispensing water

This refrigerator door gasket forms an airtight seal between the door and cabinet to keep cold air in and humid air out. Replacing a worn gasket helps stabilize temperatures, reduce frost and condensation, and improve overall cooling performance.

• Seals the door perimeter to prevent air leaks
• Helps maintain set temperatures and humidity levels
• Reduces frost buildup and condensation around the door
• Common symptoms include rips/tears, warping, gaps, poor door seal, or visible moisture/frost at the door

• Disconnect power; let the interior warm slightly to soften the old gasket (or warm the new gasket in hot water)
• Pull the old gasket from the retainer/groove and clean mating surfaces
• Press the new gasket fully into the retainer, seating the corners first and working evenly around the door
• Use warm water or low heat to relax wrinkles; adjust door/hinges if needed

The Mullion Heater is an OEM part for Bosch refrigerators. It is designed to prevent condensation from forming on the refrigerator door mullion, the vertical divider between the doors. This heater ensures that the mullion stays warm enough to stop moisture from condensing and causing potential water damage or mold growth.

Causes of a bad mullion heater can include electrical failures, wear and tear from continuous use, or manufacturing defects.  

Symptoms of a bad mullion heater include:

• Visible condensation or frost on the door mullion
• Water pooling or dripping around the door area
• Increased humidity inside the refrigerator
• Mold or mildew developing near the door seal

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This condenser fan motor spins the fan that moves air across the condenser coils and around the compressor. Replacing a weak or seized motor restores proper heat removal so the cooling system can maintain stable temperatures and run efficiently.

• Drives the condenser fan to move airflow through the condenser section
• Helps dissipate heat from the refrigeration system and cool the compressor
• Failure may present as the condenser fan not running
• May also cause warm temperatures, longer run times, or loud scraping/whirring noises near the rear or bottom of the unit
• Can contribute to the compressor running hot

• Disconnect power before servicing; use gloves to protect from sharp edges
• Access the condenser area; install the new motor in the same orientation as the original
• Transfer the existing fan blade, bracket, and grommets if required; keep wiring clear of the blade
• Restore power and verify fan operation with the system running

This halogen light bulb restores bright, reliable illumination in your appliance so you can clearly see the cooking area or interior. Replace a burned-out or flickering bulb to maintain visibility and safe operation. What it does:

• Provides illumination inside the appliance or over the cooking surface
• Replaces a failed halogen lamp to restore proper lighting
• Typical symptoms: light won't turn on, is dim or flickers, or works intermittently
• Helps you monitor food and check progress without guesswork

• 1 halogen lamp

• Disconnect power/unplug and allow the bulb and surrounding area to cool completely before service
• Access the lamp per your model's instructions; remove any lens or cover carefully
• Handle the new halogen bulb with gloves or a clean cloth; avoid touching the glass capsule
• Match the bulb type and rating specified for your model; do not exceed the rated wattage

This active carbon filter refreshes the air when your range hood is set to recirculate. Replace a saturated filter to restore effective odor reduction and maintain a more comfortable cooking space. What it does:

• Adsorbs cooking odors in recirculating operation
• Helps maintain fresher indoor air when venting back into the room
• Restores odor-removal performance when the old filter is saturated
• Typical signs it's time to replace: persistent cooking smells or diminished odor reduction

• One activated carbon filter

• Disconnect power to the hood before servicing
• Remove the metal grease filter(s) to access the charcoal filter
• Release the old filter from its clips/bayonet mount and install the new filter in the same orientation until it locks
• Charcoal filters are not washable; replace when saturated

• For hoods configured for recirculation; not used when vented to the outdoors

This part is the gasket that is used on refrigerator doors. This part surrounds the perimeter of the refrigerator door and acts as a seal to both keep the cold air in the fridge but also keep the warm air out. It is white in color.Due to normal wear and tear, the gasket may become brittle and wear out over time so that it is no longer effectively sealing the door shut. It can also become torn or cut, which would also require a replacement. A quick visual inspection can determine if it needs to be replaced. If there are folds or creases in the replacement gasket, let it soak in warm water to help straighten it back out.This gasket is compatible with refrigerator units that are manufactured by KitchenAid, Thermador, Jenn-Air, Whirlpool, and Dacor. It is sold as an individual part. This gasket comes directly from the manufacturer.

This is a Whirlpool freezer gasket.If the freezer is having difficulties staying at temperature and the old gasket is damaged or off track, replacing the gasket could fix the problems. A faulty gasket could also lead to higher levels of ice and frost build up in the freezer. This could potentially raise an energy bill because it causes the freezer to stay engaged longer. Higher levels of frost build up could ultimately damage other components. Pull the old gasket out before installing the new one. It doesn't matter if the old part gets snagged or torn when it's taken out since a replacement is ready. Be sure not to break any of the fastening clips around the edge of the freezer. Slowly insert the gasket around the outer edges of the freezer lid, inserting the lip of the gasket into the cut out areas. Make sure the gasket is held tightly in place before shutting the freezer lid.This part is sourced directly from the manufacturer as a genuine OEM replacement part. This gasket is only available individually and is not included with any other parts or the original appliance. This product is compatible with Whirlpool brand freezers.

This evaporator fan motor circulates cold air across the evaporator and throughout the compartments for even cooling. Replacing a worn motor restores proper airflow, temperature consistency, and overall defrost performance.

• Circulates air over the evaporator coils and through the vents to cool both compartments
• Helps maintain stable temperatures and supports effective defrost
• Failure symptoms include weak/no airflow, warming in one or both sections, frost buildup on the evaporator cover, or loud/intermittent fan noise
• Motor may start or may run intermittently, causing long run times

• Disconnect power before servicing; internal panels and fan blades can be sharp
• Access the motor behind the freezer's rear panel; remove shelves/ice maker as needed
• Transfer the original fan blade and any mounts/grommets to the new motor; match blade orientation
• Route wiring as original, secure the motor, and ensure the fan spins freely before reassembly