Thermador Refrigerator Parts

This condenser fan blade mounts to the fan motor and pulls air across the condenser coil and compressor. Replacing a cracked or warped blade restores airflow so your refrigerator cools efficiently and the compressor runs at a safe temperature.

• Circulates air through the condenser coil and over the compressor to remove heat
• Helps maintain cooling performance and stable system pressures
• Common symptoms: weak or no airflow at the rear/base, rattling or scraping noises, wobble/vibration, visible cracks or missing fins, warmer-than-normal compartments or hot cabinet sides
• Works with the condenser fan motor and shroud; typically replaced when the hub is stripped or the blade is damaged

• Disconnect power and pull the refrigerator out; remove the rear access cover near the compressor
• Note blade orientation and depth on the motor shaft before removal
• Pull the old blade straight off; press the new blade onto the shaft until fully seated and ensure it spins freely with proper shroud clearance
• Reinstall the cover, restore power, and verify strong, quiet airflow

This refrigerator ice auger sits inside the ice bin and rotates to move cubes or crushed ice toward the chute. Replacing a worn, bent, or stripped auger restores smooth, consistent dispensing performance. What it does:

• Rotates inside the ice bin to feed ice toward the crusher and dispenser chute
• Helps deliver either cubes or crushed ice depending on the selector
• Common symptoms: dispenser motor runs but no ice comes out, weak/intermittent dispensing, frequent ice jams, or grinding noises from the ice bucket

• 1 ice auger

• Unplug the refrigerator before servicing; remove and empty the ice bin
• Note the order of internal parts during disassembly; transfer any reusable hardware from the original assembly
• Wear cut-resistant gloves—metal and plastic edges can be sharp
• Reassemble so the auger turns freely by hand, reinstall the bin, restore power, and test the dispenser

This replacement light bulb restores clear, reliable illumination so you can see contents and monitor appliance operation. Replace a burned-out, dim, or flickering bulb to bring visibility back to the area it lights. What it does:

• Provides illumination in the appliance's interior or designated lighting location
• Makes it easier to see contents and check status at a glance
• Common symptoms: light won't turn on, intermittent/flickering light, dim or blackened bulb

• 1 light bulb

• Disconnect power before servicing; allow hot surfaces and the old bulb to cool completely
• Remove any lens/cover, then remove the old bulb
• Install the new bulb securely without overtightening; reinstall the lens/cover if present
• Restore power and test operation

This refrigerator compressor is the heart of the sealed cooling system. It compresses and circulates refrigerant so the fresh food and freezer sections reach and maintain set temperatures, restoring cooling performance when the original unit has failed.

• Compresses and moves refrigerant through the evaporator and condenser to remove heat from the cabinet
• Restores cooling when a failed or seized compressor is the cause of no-cool/weak-cool conditions
• Symptoms include a warm refrigerator or freezer, extended run time with little cooling
• Clicking or humming from the compressor area with no start, or overheating and cycling on overload

• Sealed-system service requires EPA Section 608 certification, recovery equipment, brazing, deep vacuum, and precise recharging
• Disconnect power and properly recover refrigerant before opening the system; replace the filter-drier, braze with nitrogen purge, leak-test, evacuate, then charge to the specification on the model's data plate
• Transfer any model-specific grommets, brackets, tubing, and external inverter/start components from the original unit or replace as directed in the service manual

This defrost bi-metal thermostat senses evaporator temperature during the defrost cycle and opens to stop heater power at the safe cutoff. Replacing a failed thermostat restores reliable defrosting and helps prevent ice buildup that restricts airflow and cooling.

• Monitors evaporator temperature to control the defrost heater
• Closes when cold to allow defrost; opens at cutoff to terminate defrost and prevent overheating
• Helps maintain clear evaporator coils for proper airflow
• Common symptoms: heavy frost on the back wall/evaporator, poor cooling, or defrost heater not energizing

• Disconnect power before servicing; wear cut-resistant gloves
• Access the evaporator; mount the thermostat in the original location with firm contact on the tubing
• Transfer any original clip or insulation as found to ensure proper sensing
• Secure all connections and route wiring away from the heater and moving parts; clear existing ice before restoring power

This door hinge restores smooth, aligned door operation. Replacing a worn hinge ensures the door opens and closes properly, supports the door's weight, and helps the gasket seal evenly to reduce air or heat loss.

• Provides the pivot point that lets the door open and close smoothly
• Maintains door alignment so the seal sits flush against the cabinet
• Helps prevent sagging, rubbing, or binding at the door edge
• Common symptoms: door drops or won't close flush, squeaks/pops, visible play or hinge damage

• Disconnect power; turn off water supply if applicable
• Support the door before removing hinge fasteners to prevent strain or damage
• Transfer any spacers/bushings from the old hinge to the new hinge if present
• Reinstall and verify door alignment and seal contact; adjust as needed

Located inside the freezer's ice bucket, this ice auger is the helical shaft that rotates to move cubes toward the chute for cubed or crushed ice. Replacing a worn or bent auger restores dispensing and helps prevent jams and grinding.

• Rotates with the dispenser motor to move ice through the bucket and into the chute
• Works with the crusher assembly to provide cubed or crushed ice
• Damage or wear can cause jamming, slow/weak dispensing, or loud grinding during dispense
• Often replaced when the dispenser motor runs but little or no ice is dispensed

• Disconnect power to the refrigerator; remove the ice bucket from the freezer
• Disassemble the bucket/crusher housing; transfer blades, spacers, and hardware to the new auger in the same order and orientation
• Handle sharp metal parts with care; wear cut-resistant gloves
• Reinstall the bucket fully seated; restore power and test both cubed and crushed functions

The Water Filter Cap is an OEM part for Bosch refrigerators. This secures the water filter within the refrigerator, ensuring a snug and leak-free fit. 

The need for a replacement can arise if the original cap is lost during a filter change, damaged, or wears out over time. 

Symptoms of a missing or damaged Water Filter Cap include:

• Difficulty in installing or securing the water filter properly, which could lead to water leaks inside the refrigerator.
• Contaminants or particles in the dispensed water, indicating that the filter is not fully sealed and thus not effectively filtering the water.
• The water filter becoming loose or falling out, compromising the refrigerator's ability to provide clean, filtered water.

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This replacement roller fits the front or rear position of a slide mechanism, restoring smooth, even movement and reducing noise when a wheel is worn or broken. It helps racks or drawers glide properly and stay aligned. What it does:

• Provides low-friction rolling support for the slide track
• Helps slide-out assemblies move freely without binding or scraping
• Worn or damaged rollers can cause sticking, squeaking, or uneven travel
• Restores proper alignment and smooth operation when replaced

• 1 roller assembly

• Disconnect power and allow the appliance to cool before servicing
• Remove the slide-out assembly; note roller orientation and hardware
• Transfer/reuse existing screws, clips, or retainers as required
• Do not lubricate unless the manufacturer specifies a lubricant

The Cooktop Bracket Kit is an OEM part for Bosch cooktops. This bracket and hardware kit serves to securely fasten the cooktop surface to the underlying countertop.

Causes of a bad bracket can include wear and deformation from heavy cooktop use over time, or damage to fastening screws from accidental impacts.

Symptoms of a bad bracket and fastening kit include:

• The cooktop surface becoming loose, wobbly, or unstable during use
• Gaps appearing between the cooktop and countertop edges
• Reduced heat containment and risk of burns from loose surfaces

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This support mounts in the dispenser area to secure the ice housing assembly. It helps keep the chute and door properly aligned so ice dispenses smoothly and the opening seals as designed.

• Supports and positions the ice housing/chute assembly in the freezer door
• Helps maintain proper alignment and sealing of the ice door/flapper
• Reduces wobble or flex that can affect dispensing performance
• Typical signs it may be needed: loose or misaligned dispenser housing, ice or air leaking at the chute, frost buildup around the dispenser, inconsistent ice dispensing

• Disconnect power to the refrigerator before servicing
• Remove the dispenser trim/control to access the housing; handle wiring and tabs carefully
• Remove mounting fasteners, replace the support, and transfer any reusable hardware
• Reassemble, restore power, and test ice dispensing and chute seal

The Water Inlet is an OEM component specifically designed for Bosch refrigerators featuring internal water filtration and dispensing systems. It serves as the entry point for unpurified water into the appliance.

The water inlet utilizes precise engineering to thread securely onto liquid supply lines. Its feed line transport capacity is rated to withstand regular high-pressure pulses from large filtered volumes. 

Causes for inlet replacement typically relate to normal wear at the threaded fitting connection over time. Loosening can affect water tightness and risk leak development.

Symptoms of a failing water inlet include:

• Water leakage around the inlet fitting 
• Loose inlet face or threads requiring tightening
• Diminished water flow rates into the refrigerator 

 This OEM Bosch replacement part is also compatible with Thermador, Gaggenau, and some Kenmore refrigerator models utilizing matching water system architectures. Reinstallation restores a tight seal and reliable supply transport functionality.
 

A replacement drain pan that captures defrost and condensation water to keep it contained and away from the cabinet and floor. Restores the appliance's normal water-collection path and helps reduce leaks. What it does:

• Collects melting ice and condensation from the evaporator to prevent water from pooling under the appliance.
• Channels collected water toward the drain system so it evaporates or exits as designed.
• Stops common symptoms like puddles or moisture under the unit and musty odors caused by standing water.
• Fits under the evaporator/coil area to restore proper water management.

• Disconnect power to the appliance before service to avoid electrical hazards.
• Remove the required access panels or move the appliance per the manufacturer's guidance to reach the pan.
• Lift out the old pan carefully—it may contain standing water—and position the replacement so the drain outlet and routing match the OEM layout.
• After installation, restore power and check for proper water flow during a defrost cycle; inspect surrounding seals and tubing for proper seating.

This ice maker assembly produces and harvests ice for compatible refrigerators, replacing a failed or damaged ice-making unit to restore normal ice production and cycling. Designed as a direct-replacement service part for units that use this OEM assembly. What it does:

• Forms, freezes, and harvests ice automatically as part of the freezer's ice-making cycle.
• Common symptoms it addresses: little or no ice production, ice maker not cycling, or ice trays not filling.
• Works with the refrigerator's water inlet and control signals to dump ice into the bin when ready.
• Replaces a defective ice-making module to stop intermittent operation or visible damage to the ice tray.

• Disconnect power and shut off the water supply before beginning replacement.
• Remove the ice bin and interior trim panels as needed to access the ice maker; keep track of mounting screws.
• Disconnect the wiring harness and water inlet tube carefully; avoid forcing connectors or pinch points.
• After installation, restore power and water, check for leaks, and run the ice-maker test/diagnostic cycle per the refrigerator's service instructions.