Wall Oven Switch

This genuine replacement wire harness connects and routes power and signal lines between appliance components, restoring reliable electrical communication for normal operation and control response. What it does:

• Replaces damaged or frayed wiring that can interrupt power or signals
• Restores reliable connections between controls, motors, and sensors
• Helps resolve intermittent operation, loss of certain functions, or failure to start when caused by wiring faults
• Provides factory-style connectors and routing for secure, vibration-resistant connections

• Disconnect power to the appliance before starting any repairs
• Handle connectors carefully; match connector shapes and colors to the original
• Route the harness as the OEM diagram specifies and secure with clips or ties to prevent chafing

Color: White

This latch switch secures the appliance door and signals the control when the door is closed, helping the unit operate safely and reliably. It's a direct-fit replacement that restores reliable door engagement and switch activation. What it does:

• Physically latches the door and provides the electrical switch signal to the control
• Prevents operation when the door is not fully closed or latched
• Common symptom: appliance won't start or cycles because the door isn't registering closed
• Common symptom: door won't stay securely latched or feels loose when closed

• Disconnect power (unplug or shut off circuit breaker) before installing to avoid shock
• Installation typically requires removing the door or control panel and basic hand tools
• Handle the switch and wiring harness carefully; avoid forcing connectors
• Test door operation and continuity of the switch before reassembling

This replacement switch restores reliable control of a specific circuit or feature in your appliance. A button, selector, or lever that has become unresponsive or intermittent can be fixed by installing a new switch.

• Opens and closes an electrical circuit to power the intended component or feature
• Helps resolve no-response or intermittent operation from a selector or button
• Addresses issues like a stuck/broken actuator or a switch that only works when wiggled
• Supports safe, consistent control of the appliance function

• Disconnect power to the appliance before servicing
• Note wire positions and transfer one lead at a time to the matching terminals
• Seat the switch fully in its mounting; avoid pinching or straining wires
• After reassembly, restore power and test operation; use a multimeter to confirm continuity if needed

The Surface Element Control Switch is an OEM part for Frigidaire ranges. It is responsible for regulating the heat output of the surface elements on your range, allowing you to adjust the temperature for different cooking needs.

A bad surface element control switch can be caused by wear and tear, electrical issues, or component failure. When the control switch becomes faulty, it can result in issues such as the surface elements not heating up, inability to adjust the temperature, or inconsistent heat output.

Symptoms of a bad surface element control switch include:

• Surface elements not heating up
• Inability to adjust the temperature of the elements
• Surface elements heating unevenly or inconsistently

Replace your faulty surface element control switch with this genuine OEM Frigidaire part to restore your range's surface elements. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This is a black rocker switch used to control a function on compatible ranges/cooktops. Replacing a worn or inoperative switch restores positive on/off control and reliable operation of the connected feature.

• Controls an appliance function (such as a light or igniter circuit) with a single on/off action
• Common failure signs: switch won't stay on, no response when toggled, intermittent operation, or physical damage/discoloration
• Direct-fit replacement designed for the original switch location
• Helps restore safe, predictable control to the appliance

• Disconnect power and, if applicable, shut off gas before servicing
• Access is typically from the control panel; retain orientation of wires and note terminal positions
• Transfer wires one at a time to the new switch to avoid miswiring
• Inspect connectors for heat damage; replace damaged terminals before reassembly

This is a replacement right switch sail — the right-side actuator that mounts to the appliance control panel and engages the underlying switch. It restores a positive tactile lever so the control switch can be operated reliably. What it does:

• Replaces a broken, cracked or missing right-side switch actuator on the control panel
• Provides a firm, consistent surface to engage the underlying electrical switch
• Helps eliminate loose, stuck, or non-responsive control levers
• Restores correct alignment so the switch clicks and functions as intended

• One right switch sail (actuator) as shown

• High-level swap: remove the control panel trim, lift out the old actuator, and snap the new sail into the switch housing
• Use care to avoid damaging nearby plastic tabs or the switch; verify correct orientation before snapping into place
• Disconnect power to the appliance before starting any repair to avoid electrical shock

The Fan Switch is an OEM replacement part for GE cooktops. Measuring approximately 2 inches by 1 inch, this fan switch serves as a component in activating the downdraft fan. The downdraft fan aids in extracting smoke, steam, and odors, promoting a cleaner and fresher cooking environment.

A malfunctioning Fan Switch can be attributed to electrical issues, wear and tear from regular use, or physical damage. These problems can lead to the downdraft fan not activating, resulting in inadequate ventilation and the accumulation of smoke and odors during cooking.

Symptoms of a bad Fan Switch include:

• The downdraft fan failing to activate, leading to poor ventilation
• Accumulation of smoke and odors during cooking
• The switch being unresponsive or failing to maintain the fan’s operation

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Large.

A replacement door switch that lets the appliance detect door open/close and enables normal operation and lighting. Restores reliable door sensing so cycles start and interior lights respond when the door opens. What it does:

• Detects when the door is opened or closed so the appliance can start or stop cycles safely
• Enables or disables the interior light based on door position
• Commonly replaces a faulty or intermittent switch that prevents the unit from starting or the light from working
• Simple electrical/mechanical switching — designed to match original function

• Disconnect power before inspecting or replacing the switch to avoid shock risk
• Access may require removing the control panel or inner door trim depending on model
• Handle the switch and connectors carefully to avoid damaging terminals or wiring

This is a replacement LIS CMT switch used to restore proper electrical switching for the control module and motor circuits. It helps return normal operation when the original switch is worn or failed. What it does:

• Acts as an electrical switch for the control module and motor circuitry
• Enables the appliance to complete control signals needed for motor or control functions
• Commonly linked to symptoms like no motor response, intermittent operation, or unresponsive controls
• Provides a direct replacement that fits the original mounting and connector arrangement

• Disconnect power to the appliance before attempting any repairs to avoid shock
• Handle the switch and connectors carefully to avoid damage to terminals or wiring
• Verify connector orientation and secure mounting when installing the new switch

Color: Black