Search Results

• Doesn't shut off
• Won't start
• Will not tumble

I realized my load of laundry was still wet after a normal drying cycle. My first action was to turn the dryer on (2010 gas Maytag centennial) and open the front port to look at the ignitor coil. It never turned orange so I knew there must be a problem with the primary circuit. I shut off the dryer, disconnected the power, pulled it away from the wall, shutoff the gas, and removed the back panel. I then disconnected the wires for the thermal fuse and checked its resistance with a multimeter.... Read more

• Won't start
• Element will not heat

After an internet search, the likely problem was a faulty "Element Switch.." I actually unplugged the stove and removed the switch (I did NOT disconnect the wires). I obtained the part number on the switch, disassembled it, observed that the contacts were highly degraded, reassembled the switch and reinstalled it back into the stove. This all provided confidence the SWITCH was faulty. One switch on the AppliancePartsPros.com website (AP2591804) looked exactly like the switch in the stove... Read more

I got online and found AppliancePartsPros.com. I found others had the same problem, and had replaced the switch, with my model number your rep got me the exact switch and a video on how to change it. It took approx 15-20 min . was very happy with the service, will use again in future if needed. Gary Read more

• Won't start
• Element will not heat

The fix was to replace the infinite control switch on my Whirlpool range. A simple task. Read more

• Too warm
• Clicking sound
• Won't start
• Freezer section too warm

I have a Kitchen Aid side by side refrigerator/freezer which is 8 years old. One day it just stopped cooling. At first I was just going to junk it and purchase a new one. However, I took off the lower back cover and noticed the compressor was not running. I knew from experience that these compressors need a starter capacitor and relay and it is not uncommon for these parts to fail. I looked on the Internet for a video which showed how to remove the parts. I also found a video which showed how... Read more

• Won't start
• Timer will not advance
• Will not drain

First I checked the circuit breakers and power to the outlet, then next wanted to check the lid switch, but it wasn't where I had found it on older models. I could hear it clicking on and off as I raised and lowered the lid, but it wasn't visible. I drained the tub through a siphon hose to lighten the machine, so I could slide it away from the wall to better see. Couldn't see the switch anywhere and decided it must be hiding in the raised console, but was unsure of how to attack it without... Read more

• Won't start

I replace the Infinite Switch and that seems to be the trick for keeping the temperture under control. Read more

I was trying to troubleshot a problem I had with my GE dryer not starting. I went to AppliancePartsPros.com because they have excellent DYI videos on how to make repairs. I determined that the problem was in the push start switch. I ordered the switch online and it took 3 days to arrive. It took 5 minutes to replace the switch and the dryer works perfectly. Read more

• Doesn't shut off
• Won't start

I watch the video on YouTube. And it went step by step on how to take it off and on Read more

I read a few of your reviews and found that a, "Phase Control Board" may be the problem. It was! Talk about easy to install... It was super easy! I decided to order the, "Speed Control Plate" also as a precaution (Shipping was one price - and it arrived the very next day, Wow! I didn't expect that.) With my screwdriver and good lighting. I fixed it myself! My husband is still in shock. I used forceps to install the, "Speed Control Plate," because I needed something to hold the tension wire - at... Read more

Watched the attached video, then followed directions and installed the part ordered. Read more

Removed the lower rack, removed the lower wash arm, removed the lower coarse filter, removed fine filter ( still no tools require to this point). Removed two 1/4" head screws with nut driver to then remove float switch, unplugged float switch, plugged in new switch, reinstalled filter, etc. This is a 5 minut job! Read more

• Won't start
• Lid or door won't close
• Door latch failure
• Will not agitate

Superfast parts delivery. Got packages by the second day. Videos were extremely helpful and well done; we couldn't have done without them although we came across slight differences in our machine and found workarounds. Our machine did not drain the water so I drained the water manually via drain tube at bottom of the machine and checked the filter for blockage. All clear so I read articles on the internet and watched videos and took a chance on replacing the drain pump and circulating motor... Read more

• Element will not heat

Replaced the burner Infinite switches for the burners having the issue. Here are the latest part numbers for this model Maytag. Left rear (LR) and right rear (RR) burners are both 6" and use the same switch. Part # WP3149404. Left front (LF) is an 11 1/2" burner Part# W10167742. The right front (RF) burner is a double burner 6" center and 9 1/2" outside burner Part #WPW10149355. Very simple repair. Unplug the stove, remove the rear panel, remove the switch knob, remove the 2 switch screws,... Read more

• Will not drain
• Won't start
• Will not fill with water
• Lid or door will not open

My son was doing his laundry, only to announce that the washer wouldn't rinse, spin or drain. I looked on line at new washers and was staggered to see how much they cost, our Whirlpool is 20 years old! Then I looked on Craig's list to see about getting a used washer, but when I found something that looked good, and looked up how it performed, most of them had terrible reviews. So, I looked at a video that told about the 5 most common things to go wrong and figured out it was a broken lid... Read more

Tried to fix with a non GE part, didn’t work. Your GE brand pressure sensor worked like a charm Read more