Weedeater Parts

This is a genuine replacement drive belt that is manufactured for use in select riding lawn mowers that feature double idler pulleys. This belt is specifically used on models that feature a 38- or 42-inch deck. Its job is to use the pulleys to engage and drive the cutting blades on the mower deck. Belts are subject to repetitive motion and high heat, which can cause them to crack or corrode, or even snap entirely. Replacing belts is typically considered a part of lawn mower maintenance, but some owners choose to keep an extra belt on hand in case of emergencies. Belts can also become stretched with excessive use, causing them to slip and lead to poor cutting performance. This is a genuine OEM drive belt from Husqvarna. It is compatible with select mowers from Poulan, Craftsman, and Husqvarna and fits more than 150 different models. It is made of durable rubber and will require a screwdriver or pry bar to install. Always be sure to disengage the engine and allow it to cool before performing any repairs. It is a good idea to secure the mower wheels when working under the deck, as well. This belt is sold as an individual unit and does not include any additional components.

This engine control cable is responsible for controlling not only the engine speed but also the rotation of the blades. The engine control cable attaches to the control handles of the lawnmower. When the handle is pushed down, this will activate the engine control cable to power the engine and the blades. When the engine control cable is malfunctioning, the machine's engine and blade won't move no matter how hard the control handle is pressed. Replacing the engine control cable is a straightforward procedure that requires a nut driver and pliers. Wear gloves for protection. Husqvarna manufactures this brand-new engine control cable. It has Z-type bent ends and thick, durable rubberized exterior layer. There's a plastic clip, too. It is specifically made for Craftsman, Murray, Husqvarna, Weed Eater, Ariens, Poulan, and Poulan Pro lawnmower models. It approximately measures 61 inches and is sold individually.

This genuine Husqvarna bolt and washer replacement part is specifically engineered to hold and secure the lawnmower blade in place. The bolt is threaded while the washer has a curved or rounded headed. A washer is needed for even load distribution of the threaded bolt. Fastening the bolt without the fastener may cause stress to the material it's driven into. One of the warning signs that the bolt and washer are broken is if the lawnmower blade doesn't rotate properly. Instead of moving in one circular motion, it turns erratically and goes up and down. In some cases, it will make a loud grinding noise during cutting. The lawnmower blade may even fly out from its normal position. Replacing the worn-down bolt and washer is fast and straightforward. First, shut down the engine and let it cool. Then, take out the spark plug and turn the mower on its side. Use a socket to remove the old bolt and washer. Then, grab the replacement and insert it through the blade's hole. Tighten it using the socket. This original Husqvarna bolt and washer is only suitable for lawnmowers made by Husqvarna, Craftsman, and Weed Eater. It is also compatible with some Dixon and Poulan lawnmowers. This bolt and washer replacement is sold individually.

This pinion gear is an essential part of the steering assembly as it translates the rotation of the steering shaft into vertical motion. The pinion gear travels along the drivetrain, which pushes the wheels either forward or backward, causing the mower to turn. Without a functioning pinion gear, the mower will no longer steer. A pinion gear's teeth can slowly wear away through repeated use, causing it to begin slipping. When this happens, the operator will no longer be able to turn their mower as effectively or possibly not at all. This can be dangerous for the operator and they should stop mowing immediately. With most push lawn mowers, the pinion gear is located inside the wheel well. To replace it, simply remove the wheel and mounting washer, pop off the retaining ring, and remove the pinion. Reassemble and test the forward motion of the wheel. This genuine replacement OEM part is compatible with a number of lawn mowers from Poulan, Jonsered, Husqvarna, and Weed Eater. It comes sourced from the original manufacturer and does not include any additional hardware.

This genuine Husqvarna selector knob affixes to the selector spring as part of a mechanism that lowers and raises the handle of the lawn mower for flexible usage.The selector knob might have to be replaced in the event that it suffers damage that impedes its ability to lower and raise the handles of the lawn mower. This kind of damage can occur as a result of general wear and tear from long-term usage, exposure to the elements, or a direct collision that warps the selector knob beyond repair. If any of this form of damage occurs and prevents the adjustability of the handles, the selector knob should be replaced with this genuine OEM replacement part. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer. It is sold individually. This selector knob is compatible with the following brands: Husqvarna, Poulan, Ariens, and Craftsman.

This part is a fuel tank assembly that is used on leaf blowers. This assembly includes the fuel tank, fuel lines, fuel filter, and tank cap. The fuel tank is the component that holds the fuel for the engine while the fuel lines circulate the fuel throughout the engine.A new fuel tank assembly may be needed if the original is cracked, broken, or damaged in any way. Over time, the fuel tank may become damaged due to the constant vibrations that it experiences. If this is the case, it will need to be replaced to ensure the operator's safety. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment.This part is a genuine Husqvarna part. It is sold individually. This particular fuel tank assembly is compatible with leaf blowers that are manufactured by Husqvarna, Poulan, and Craftsman.

This part is a starter pulley assembly that is used on handheld blowers. The starter pulley is the component that is used to store the rope that is part of the starting mechanism. When the rope is pulled, it rotates the pulley mechanism which then engages the flywheel to start the motor.A new starter pulley assembly may be needed if the handheld blower does not start. If the starter pulley assembly is cracked, broken, or damaged in any way, it will need to be replaced for the handheld blower to start and operate correctly. Never perform care and maintenance on outdoor power equipment that is powered on.This starter pulley assembly is a genuine Husqvarna part. It is sold individually. This particular starter pulley assembly is compatible with handheld blowers that are manufactured by the Husqvarna brand the Weed Eater brand.

This genuine Husqvarna fuel cap provides cover and protection to the hole into which engine oil is dispensed on certain lawn mowers, lawn tractors, and snowblowers. This fuel cap should remain closed when the appliance at hand is not in use in order to prevent leakage.If the engine of a small engine appliance is suffering from frequent leakages, there could be damage in the fuel cap that is causing the leaks. A fuel cap could also become misplaced. If the cap is broken or lost, it must be replaced immediately before using the small engine appliance again. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This fuel cap is compatible with the following brands: Husqvarna, Poulan, Ariens, and Craftsman. This part is sold individually.

This engine zone control cable is an authentic OEM replacement part for a push lawn mower. This cable connects the engine to the control bar and is essential for the engine to run. A control bar acts as a safety mechanism that keeps the engine from running unless it is depressed. Therefore, without this cable, the engine and control bar will be out of communication and the engine will not start or run. Like with any cable, an engine zone control cable can snap if put under too much pressure. Often, temperature changes can cause the cable to tense, and when a user pulls the cable, it can snap. The most obvious sign of a broken engine zone control cable is that the control bar has a lot more give and the engine will not start. Replacing the cable is an easy job. Simply remove the broken cable from the control bar and release it from the stop lever using a pair of pliers. This part is compatible with Poulan, Ryobi, Weed Eater, Jonsered, and Husqvarna push mowers and is sourced from the original manufacturer. This part ships individually.

The carburetor kit has a metal body that is designed to withstand high temperatures, a rubber primer bulb, and a plastic throttle lever. The carburetor is an integral part of engines in lawn and garden equipment. This is where the air and fuel will be mixed before being sent into the engine. The air comes in through the intake tube, and it flows into a smaller tube, where the fuel is injected through small holes in the carburetor body. Then, the two are mixed and released into the engine through a butterfly valve, which controls the amount of fuel going to the engine for optimal performance. The carburetor can become clogged over time or even be broken or damaged. If the engine is not running properly, the carburetor may need to be replaced. This is a simple replacement that only requires a screwdriver. Make sure to always disconnect the spark plug and wear gloves when performing engine repairs. This kit can be used with several models of lawn and garden equipment, including brands like Weed Eater, Paramount, Poulan, Jonsered, and Husqvarna.

This is a genuine OEM mandrel kit with a nut that is sourced directly from the manufacturer. It is designed for use on lawnmowers, tractors, and other outdoor lawn and garden equipment. The mandrel is responsible for spinning the blades on lawn mowers. It is part of the deck and can be a safety issue if not properly attached or if broken. If the spindle is broken or bent during use, it is apparent by uneven cutting, loud squealing, or vibrations, and buzzing sound. Mandrel replacement should be on a flat service for safety. If the mower is hot, allow it to cool before making repairs. Remove the spark plug and empty the gas tank. If the deck on the mower is removable, remove it before jacking the mower up. Once the mower is in the air, remove the blades to access the spindle. Remove the spindle. This is an excellent time to check the bearings and replace them if needed. Install the new spindle. Reinstall the blades. Lower the mower and if the deck was removed, reinstall the deck. This mandrel kit is made of high tensile metal; it comes with the nut for installation; it is sold as an individual unit. This mandrel kit is compatible with lawn mowers manufactured by Husqvarna Poulan, Weed Eater, and Ryobi.

This replacement part is an ignition switch and is intended for use in a variety of lawn equipment. This is a genuine replacement part made by Husqvarna. The ignition switch is an important part of many different lawn mowers, as it allows the appliance to be turned on.A new ignition switch might be needed if the current one is damaged, broken, or if the key blade is snapped off in the ignition. If the user is unable to start the machine through the ignition switch, it is likely damaged or malfunctioning. It is possible for the ignition switch might need to be replaced after years of normal wear and tear. Be sure the equipment is completely powered down and cooled off before attempting to repair an appliance. For more detailed instructions on how to install this specific part, see the owner's manual. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with different types of lawn equipment made by Husqvarna.

This part is a replacement drive control cable. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part can be used to replace a snapped, worn, or faulty drive cable in a variety of lawnmower models. The drive control cable enables the equipment user to have proper control over the lawnmower and is essential for maneuverability. Cables can become worn or stretched or may snap with regular use. If this occurs, the lawnmower may not be drivable, and this part must be replaced. It is always recommended that the appropriate safety precautions are adhered to when attempting to fix any power tools or machinery. When working on or near an engine, ensure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this drive control cable, the appropriate owner's manual and included diagrams should be referenced.As an authentic replacement part, this drive control cable is suitable for use on several different models of lawnmowers manufactured by Husqvarna and Poulan. This is a genuine part made of high-quality, durable materials and is sold individually.