White Westinghouse Chassis Or Cabinet

The Oven Bottom Panel is an OEM component for Frigidaire oven models. Located on the base of the oven interior, this metal panel provides structure and support. 

Causes of a bad oven bottom panel include warping or damage due to exposure to high heat over time. Small nicks or cuts could allow heat to escape and reduce the oven's efficiency. Intentional or accidental impact during cleaning can also weaken the material.

Symptoms of a bad oven bottom panel include:

• Uneven or inefficient heat distribution within the oven
• Visible warping or damage to the panel surface
• Reduced heat retention leading to longer cook times
• Potential safety hazards if the metal is weakened

This OEM Frigidaire part is also compatible with some Kenmore models. 

This burner box is the structural pan beneath the cooktop that supports the surface burner components and shields internal parts from heat and spills. Replacing a damaged box restores proper burner alignment and a stable, secure cooking surface.

• Provides a rigid housing under the cooktop for burner heads, igniters, and related hardware
• Helps contain spills and protect wiring and insulation from heat exposure
• Keeps burners aligned so they sit level and openings match the main top
• Common failure signs: rust-through, cracks, or warping; stripped/broken mounting points; burners wobble or won't secure properly

• Disconnect power and shut off the gas supply before servicing.
• Remove the main top; document locations and transfer burners, igniters, grommets, and brackets to the new box.
• Handle sheet-metal edges carefully; wear cut-resistant gloves.
• After reassembly, restore gas and power, verify ignition, and leak-test any disturbed gas connections.

This access panel service cover replaces a damaged or missing cover to protect internal components and give technicians safe access for diagnostics and repairs. It restores a finished appearance while preventing dust and debris from entering service areas. What it does:

• Covers and protects internal components, wiring and controls from dust and damage.
• Provides a removable service access point for diagnostics and repairs.
• Common symptoms: cracked, bent, loose or missing panel; exposed components; rattling or drafts near the service area.
• Replacement helps restore safety, reduce drafts and eliminate noise caused by a loose or damaged panel.

• Disconnect power (and water if applicable) before removing or installing the panel.
• Wear gloves to protect hands from sharp sheet-metal edges.
• Reuse existing screws or mounting clips when possible; basic hand tools typically required.

This replacement control panel restores the appliance's front console and user interface so buttons and the display work reliably. It provides the visible face and mounting surface for controls and status indicators. What it does:

• Houses the appliance's buttons, touchpads, and display area so you can select settings and see status
• Replaces cracked, scratched, or cosmetically damaged panels that affect appearance or button access
• Helps when buttons are unresponsive due to a damaged front panel
• Restores a clean mounting surface for switches and overlays

• Disconnect power before starting any repair to avoid shock or injury
• Remove trim, bezels, or mounting screws as needed to access the panel; keep fasteners for reassembly
• Handle carefully to avoid scratching or cracking; use proper tools to release clips

Note: Comes with rear bearing (not available separately)

White

This base is the lower cabinet support that stabilizes and secures the appliance on the floor, helping keep the cabinet level and reducing vibration. It restores proper fit and prevents wobble or rubbing against the floor. What it does

• Supports the appliance cabinet and maintains alignment with the floor
• Reduces vibration and rattling caused by an unstable or damaged base
• Prevents cabinet edges or components from contacting the floor
• Helps ensure doors and drawers operate smoothly by keeping the cabinet level

• Disconnect power and water before beginning any service
• Lift or tilt the appliance only as recommended by the manufacturer; use two people for large appliances
• Inspect mounting hardware and shims; replace any damaged fasteners for a secure fit

This burner box is the steel housing that supports and protects the gas valves, burners and internal gas components in a gas range. It restores proper alignment and containment for safe, efficient burner operation. What it does:

• Houses and secures the range's gas valves, burners and related internal parts
• Directs and contains gas flow and flame components for reliable ignition
• Helps prevent gas or flame exposure to surrounding cabinet areas
• Commonly replaced when the original box is dented, damaged, corroded or interfering with burner alignment

• Replace only after disconnecting gas and power; follow appliance shut-off procedures
• Inspect related seals, gaskets, valves and fasteners during installation; replace as needed
• Use common hand tools; avoid bending or distorting the box during fitment