Whirlpool Dryer Parts

This is the socket that holds the drum light bulb inside the dryer. It provides the electrical connection to power the interior light that illuminates the drum when the door is opened. Replace this socket if the dryer drum light does not turn on even with a new bulb, or if the socket appears melted, cracked, or has damaged electrical contacts.

This hinge guide is the small bushing the hinge pin rides in. It reduces friction and keeps the panel aligned so the door or lid opens smoothly and closes flush for reliable everyday use.

• Provides a low-friction bearing surface for the hinge pin
• Helps maintain door/lid alignment so it closes flush
• Wear can lead to sagging, scraping, squeaking, or binding
• Restores smooth operation and consistent closing when the original is worn

• Disconnect power; shut off water supply
• Support the door or lid before loosening hinge fasteners
• Remove the worn guide and install the new guide on the hinge pin or in the hinge bracket
• Reassemble, then check alignment and smooth open/close

White timer knob that fits onto your dryer's timer shaft. Replace if yours is cracked, broken, worn, or missing to restore cycle selection control.

This control knob assembly replaces a worn or broken selector knob so you can set and change appliance functions with a secure fit and clear detents. It restores reliable manual control for common user settings. What it does:

• Fits onto the control shaft to select cycles, temperatures, or settings depending on your model
• Provides tactile detents and a firm grip for accurate selection
• Resolves symptoms like a loose, cracked, or spinning knob that won't engage settings
• Prevents slipping or intermittent control inputs caused by a damaged knob

• Disconnect power (unplug or shut off breaker) before handling control parts
• Often installs by aligning onto the control shaft and pushing on until seated; some models may use a retaining clip or screw
• Handle gently to avoid damaging the control shaft or surrounding panel

Fix a dryer that won't heat with this thermostat. Regulates heating element temperature to prevent overheating. Moderate DIY repair in under an hour.

Flat metal washer that distributes load and secures fasteners in your dryer. Replace if worn, corroded, or missing to restore proper fastener grip.

This touch-up paint bottle restores small chips and scratches on painted appliance surfaces to improve appearance and help protect against rust. Easy-to-apply formula matches common appliance finishes for quick cosmetic repairs. What it does:

• Covers small chips, nicks and surface scratches to improve appearance
• Helps protect exposed metal from moisture and surface corrosion after damage
• Provides a precise application for targeted repairs on doors, panels and trim
• Can be used on painted steel and metal appliance surfaces (test in an inconspicuous area first)

• Clean and dry the repair area; remove loose paint and corrosion before applying
• Shake bottle well and apply sparingly with included applicator or a small brush
• Allow adequate drying time between coats and follow any manufacturer cure instructions on the label
• Wear gloves and work in a well-ventilated area; keep away from open flame and out of reach of children

This front bulkhead is the large panel that forms the front wall of the dryer drum compartment and supports the drum as it rotates. It typically includes the opening where clothes are loaded and may include a felt seal to prevent air leaks. Replace this bulkhead if it is warped, cracked, or if the drum seal surface is damaged - symptoms include unusual noises, clothes getting caught between the drum and panel, or heat escaping from the front of the dryer.

Mounting screw secures panels, brackets, and trim to the appliance frame. Replace if screw is stripped, missing, or damaged to restore secure fastening.

If your dryer takes too long or overheats, a worn blower wheel may be reducing airflow. This assembly restores proper air circulation through the drum.

Replacement mounting screw for securing panels, brackets, and internal components. Needed when original screws are stripped, missing, or damaged during repair.

This cycling thermostat monitors the air temperature inside the dryer drum and signals the heating element to turn on or off to maintain the correct drying temperature. It is typically mounted on the blower housing or exhaust duct. Replace this thermostat if the dryer is not heating, overheating, or shutting off too early during a cycle.

Dryer drum not spinning or rotating slowly? This drive motor rotates the belt that spins the drum. Moderate DIY repair restores normal operation.

This replacement door handle restores a secure, easy-to-grip surface for opening and closing the appliance door and refreshes the door's appearance. Designed to match factory fit and function when the original handle is cracked, loose, or missing. What it does:

• Provides a firm, ergonomic grip for opening and closing the appliance door.
• Restores proper mounting and alignment if the original handle is damaged or wobbly.
• Helps prevent injury from sharp or broken handle edges.
• Improves the appearance of the appliance door when the original is faded, cracked, or missing.

• One replacement door handle

• Before starting, disconnect power to the appliance or unplug it to reduce shock risk.
• Remove any trim or access panels per the service instructions to access handle fasteners.
• Keep original screws and small parts; use the OEM diagram to confirm orientation and placement.
• Do not overtighten fasteners—snug only to avoid cracking the handle.

This is a dryer door handle with a chrome shadow finish. It mounts to the front of the dryer door and provides a grip for opening and closing the door. Replace this handle if it is cracked, broken, or loose, making it difficult to open the dryer door securely.

The Bulkhead is an OEM component for Whirlpool dryers. As a structural panel, it secures the rear of the appliance while enabling airflow behind sliding doors. 

Formed from durable composite, the lightweight bulkhead installs easily into precise slotted tracks inside the chassis. This allows full retraction during maintenance without removing additional panels. 

Causes of a faulty bulkhead can include cracked welds or screws stripping their anchors from extreme force vibration over many years of use.

Causes of a bad bulkhead can include:

• Noisy rattling and resonance as the dryer operates  
• Restricted door movement from misalignment
• Inability to fully access internal components  
• Excessive ducting leaks from gasket compression failure

Replace yours with this genuine Whirlpool bulkhead to restore smooth, tight operation. Compatible with Kenmore, Maytag, and KitchenAid dryers.