Whirlpool Range / Cooktop / Oven Parts

This top burner igniter is a genuine Whirlpool part, sold individually. This top burner igniter can be used as a replacement part in a gas range. This part fits into the surface burner orifice holder to connect to the spark module such that the gas can be turned on to heat up the burner.A top burner igniter might have to be replaced at some point in the lifespan of a gas range. A top burner igniter can be subject to damage if the connection between the igniter and the spark module is severed or is malfunctioning. The primary symptom of a malfunctioning top burner igniter is a gas burner that will not start or ignite properly. If this occurs, the top burner igniter should be removed and replaced with this genuine OEM replacement part before using that burner of the gas range again.This is an OEM part sourced directly from the manufacturer. This top burner igniter is compatible with the following appliance brands: Whirlpool, Amana, Jenn Air, KitchenAid, Ikea, and Maytag.

Restore reliable baking performance with this replacement bake element. It generates heat from the bottom of the oven to reach and maintain set temperatures, so your oven preheats properly and bakes food evenly when the original element fails. What it does:

• Supplies heat to the lower oven during Bake cycles
• Enables proper preheat and stable temperature hold
• Common failure symptoms: no heat in Bake, very slow preheat, uneven baking, element not glowing, or visible blistering/breaks

• 1 bake element

• Disconnect power at the breaker or unplug the appliance; allow the oven to cool completely
• Remove oven racks; take out the element's mounting screws and gently pull the element forward to access wires
• Move wires one at a time to the new element; ensure snug, fully seated terminal connections
• Secure the element with the mounting screws, restore power, and run a brief preheat to verify operation

The membrane switch is the low-profile keypad behind your microwave's control panel. It registers button presses so you can select settings and start cooking. Replace it if keys stop responding or require excessive pressure.

• Converts keypad presses into signals for the electronic control
• Enables selection of power levels, cook times, and options
• Common symptoms: some or all keys don't work, intermittent response, must press very hard
• If the unit won't start/stop from the keypad, the membrane switch may be faulty

• Disconnect power at the breaker before servicing
• Remove the control panel to access the keypad; note ribbon orientation and routing
• Handle the flexible ribbon carefully—don't crease it—and fully seat/lock the connector

Color: brushed chrome. It measures about 2 inches in diameter.

The Surface Burner Base is an OEM part for Whirlpool ranges and cooktops. This component is a critical part of the stove's burner assembly, housing the gas outlet and providing a stable platform for the burner cap and flame spreader. It is specifically designed to handle the rigors of daily cooking, ensuring an even and controlled flame that enhances your cooking precision.

Symptoms of a failing Surface Burner Base include:

• Uneven flames or poor heat distribution
• Difficulty in lighting the burner
• Gas leaks detected around the burner area
• Visible signs of corrosion or damage to the base

Common causes for burner base issues can include continual exposure to high temperatures, spills that lead to clogging or corrosion, and normal wear and tear. 

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This control knob replaces a cracked or missing knob on your appliance's control panel. It restores positive engagement with the underlying control so you can select settings reliably and keep the front of the unit looking complete.

• Attaches to a keyed or D-flat shaft to operate the switch, valve, or timer underneath
• Allows you to choose cycles, temperatures, or burner levels as designed
• Common symptoms: knob cracked, stripped, loose/spins without engaging, falls off, or missing pointer
• Helps restore normal operation and a finished, uniform appearance

• Disconnect power; for gas appliances, also shut off the gas supply
• Pull the old knob straight off the shaft—do not pry against the bezel or panel
• Align the new knob's opening with the shaft and press firmly until fully seated
• Test the control to confirm proper engagement and function

The Knob Bezel is an OEM part for Whirlpool ranges. As a decorative cosmetic component, the knob bezel surrounds the temperature and function knobs on the oven control panel. It helps protect the knobs while enhancing the aesthetic appeal of the appliance.

Causes of a bad knob bezel include wear and tears such as scratches, dings, or cracks over time from normal use. Exposure to heat and cooking residue can also cause discoloration or warping of the bezel material.

Symptoms of a bad knob bezel include:

• An outdated or worn out appearance on the oven control panel
• Exposure of the internal knobs without cosmetic protection
• Potential interference with knob functionality from tears or cracks

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This black oven door handle replaces a cracked, loose, or missing handle and restores a secure, comfortable grip on your range. It matches the original finish and helps keep the door easy to open and close.

• Provides a sturdy handhold for opening and closing the oven door
• Replaces a handle that is cracked, broken, loose, or missing
• Helps eliminate wobble and improves door control
• Refreshes the appliance's appearance with a matching black finish

• Disconnect power and allow the oven to cool completely before servicing.
• Support the door and glass while removing inner trim screws to access the handle fasteners.
• Transfer existing end caps/mounting hardware from the old handle; align the new handle and tighten screws snugly—do not overtighten.
• Reassemble and check that the handle is secure before use.

This flame spreader sits between the burner base and cap to distribute gas evenly through the burner ports. Replacing a clogged or warped spreader restores reliable ignition and a steady, balanced flame for consistent cooking. What it does:

• Distributes gas to create an even, circular flame pattern
• Supports reliable ignition by positioning ports around the electrode
• Helps maintain proper heat output and flame stability
• Symptoms include uneven/weak flames, yellow flames, delayed ignition, or a burner that won't light

• One flame spreader

• Disconnect power and shut off gas; allow the cooktop to cool completely
• Remove grate and burner cap; lift off the old spreader (remove retaining screw if present)
• Align the new spreader over the orifice and igniter; seat fully and secure
• Do not clear ports with hard objects; use a soft brush and verify proper flame and ignition after reassembly

Note: This is a kit of 5 bezels.

This burner cap sits on top of the gas burner head to shape the flame and shield it from spills. Replacing a damaged or missing cap restores proper flame pattern, reliable ignition, and even heating.

• Shapes and disperses the burner flame for even cooking and proper simmering
• Shields the burner head/orifices from spills, grease, and debris
• Must sit level and centered for consistent ignition and flame quality
• Replace if cracked, chipped, warped, missing, or if flames are uneven or yellow

• Allow the appliance to cool completely. Turn off gas supply and power before servicing.
• Lift off the old cap; clean and dry the burner head so the new cap seats properly.
• Center the new cap on the matching burner; it should sit flat with no rocking or gaps.
• Light the burner to verify an even, blue flame; realign the cap if ignition is delayed or the flame is uneven.

This control knob replaces a damaged or missing knob on your appliance, restoring a clean look and smooth, accurate selection of settings. It lets you turn the control shaft confidently for everyday, reliable operation.

• Presses onto the control shaft to operate the switch or valve
• Allows you to adjust settings such as heat, temperature, or function
• Common symptoms include cracking, stripped insert, loose/wobbly fit, or the knob not gripping the shaft
• A worn knob can make the control hard to turn or prevent it from turning on/off

• Pull the old knob straight off; avoid prying or side pressure to prevent stem damage
• Align the knob with the shaft orientation (flat/D-shaped as applicable) and press straight on until fully seated
• Confirm the indicator aligns with Off after installation
• Disconnect power and/or shut off gas; verify model-specific fit before installation

This window gasket fits between the appliance's window glass and the surrounding frame. It cushions the pane and helps seal gaps so the window stays secure, reduces rattles, and maintains proper performance around the viewing area. What it does:

• Seals the perimeter of the window glass to the door/frame
• Cushions the glass to reduce vibration and rattling noises
• Helps limit unwanted air/heat/steam leakage around the window area
• Common signs of wear: torn or flattened gasket, visible gaps, loose or shifting glass

• 1 window gasket

• Disconnect power and allow all surfaces to cool before starting
• Support the door and glass; wear cut-resistant gloves and eye protection
• Note the gasket's orientation; seat it evenly without stretching or twisting
• Reassemble and verify an even, continuous contact around the window

This fan assembly restores proper airflow inside your appliance, moving air to cool internal components and support ventilation. Replace a seized, noisy, or non-running fan to prevent overheating and bring back efficient, quieter operation.

• Circulates air through the appliance for cooling and/or ventilation
• Helps maintain safe operating temperatures and consistent performance
• Common symptoms: no or weak airflow, fan won't start or runs intermittently, loud grinding/squealing/rattling, excessive vibration
• A failed fan can lead to overheating or thermal safety shutdowns

• Disconnect power at the breaker before servicing
• Access the fan per your model's service information; note wire locations and mounting orientation
• Transfer any brackets, screws, or gaskets from the original
• Ensure the fan wheel spins freely and nothing contacts it before restoring power

Approximate size: 19.3 x 12 inch.

This bake element restores primary heat to the lower oven cavity. Replacing a burned-out element helps bring back consistent temperatures and reliable baking performance.

• Provides radiant heat during bake cycles in the lower oven cavity
• Failure symptoms can include no heat in bake mode, very slow preheat, uneven baking, or a visible break/blister on the element
• Restores stable, even temperatures so recipes cook as intended
• Replaces an open or shorted element to return the oven to normal operation

• Disconnect power at the breaker before servicing.
• Remove oven racks and bottom panel to access the element; remove mounting screws.
• Carefully pull the element forward and disconnect the two wire terminals; do not let wires slip back into the cavity.
• Install the new element, reattach terminals and screws, restore power, and test bake.