Need Help?
Call
Burner won't light or flame won't adjust? This gas range burner valve controls flame height and shutoff. Moderate DIY repair restores safe operation.
Watched a couple of videos that closely matched my project. Warranty company couldn't find a service tech in my area so they had to refund my stove purchase. Part cost under $50. Refund: $950!! Read more
Controls and stabilizes incoming gas supply to burners and oven. Replace if regulator is cracked, leaking, or fails to maintain consistent gas pressure.
Fix unresponsive controls, blinking displays, or oven won't heat. This electronic control board restores full function. Straightforward DIY install.
Replaced Control box, Very easy to install. Remember to DISCONNECT power cord. Read more
Fix sparking or non-working igniter switches with a new switch harness. Connects control switches to cooktop wiring. Moderate DIY repair, 1-2 hours.
Replaced the Spark Module and the Wire Harness. Works like new. Read more
This part is a grill element that is used on a cooktop. The element is responsible for supplying heat to the cooking area of the cooktop. If the element is not lighting up orange or red when it is turned on, it will need to be replaced. This part may need to be replaced over time due to normal wear and tear on the appliance. Some users may also notice that the element is not heating evenly or works intermittently. If this is the case, this is a genuine OEM replacement part that is made out of high-quality materials. Unplug the range from the electrical outlet and allow the cooktop ample time to cool down before trying to replace it. Wear work gloves for safety during this process.This part is compatible with cooktops that are manufactured by Jenn-Air and Maytag. It is sold individually and comes from the manufacturer.
Ordered all the parts needed, replaced them and the Jenn Air worked just fine. Read more
Fix continuous sparking or burners that won't ignite with this spark module. Controls ignition for four surface burners with automatic reignition capability.
I watched the video, then started to work. Any confusion I went back to that section. Read more
If your gas burner won't light or clicks continuously, this igniter switch mounts on the valve stem to restore reliable ignition. Takes 5 minutes to replace.
By replacing the switch, the front right burner correctly turned on the igniter and worked. Repair took about 5 minutes. Very easy to do. Read more
This Door Hinge supports and pivots the appliance door for smooth operation and a square, reliable close. Replacing a worn hinge restores alignment so the door seals properly and opens and closes without binding or noise. What it does
Door hinge replacement and of course a new fuse. All went very well. Good service and tech support from AppliancePartsPros.com Read more
Oven not heating evenly or convection mode not working? This rear convection element restores even baking and roasting. 20-minute DIY repair.
Whirlpool convection oven. Access to convection element from inside. Three screws to remove plate covering fan blade. Then one screw to remove element bracket. I placed tape over the holes with the wires so they wouldn’t pull back into the panel. Remove old element at tabs and replace. Very easy fix. Removing door to oven made it easier to get to but not necessary. Read more
Black burner caps sit atop gas range burner heads to shape the flame. Replace cracked, worn, or missing caps to restore even cooking and a clean look.
Purchased a new Burner Cap kit. Read more
Supports and guides your range oven door for smooth opening and closing. Replace if hinge is bent, broken, or worn causing door misalignment or drooping.
With part ordered from your website. Read more
This contact spade is a push-on electrical terminal used to connect an appliance wire lead to a component's blade. Replacing a worn or heat-damaged connector restores a secure fit and consistent power flow.
Full disassembly of removable tray into top plate (stainless) and lower pan taking care not to loose fasteners. Removal of terminal blocks using lubrication on rusted screws and, if necessary, drill out technique. Unclip wires from edges of the tray on both sides without losing the clips for future re-use. Top plate is now completely free of connections and may be cleaned/scrubbed separately in advance of re-assembly. Unfasten spade insulation block (located in the front of the tray) after... Read more
Black glass cooktop surface for electric ranges. Replaces cracked, broken, or damaged glass tops. Installs over heating elements with trim brackets.
VERY simple fix- you do not even have to pull the range out.. I ordered a new cooktop from Appliance parts Pros. The customer sales rep Alphonso was great and walked me through the general process. I could find no explicit instructions for the repair but I muddled my way through. The fix is simple on Kitchenaid/Whirpool slide in ranges. 1. Open the oven door and remove the two phillips head screws directly below the control panel that hold the panel down.2. Lift the control panel upward and... Read more
Control knob for range. Attaches to control shaft on front panel. Replace if original knob is cracked, broken, worn, or missing to restore appearance.
Fix burner clicking or failure to light with a new surface igniter. Restores reliable spark ignition on gas cooktops and ranges. DIY repair in 15 minutes.
Replacement oven door glass window panel for electric and gas ranges. Installs in the door assembly to restore clear visibility when cracked or shattered.
Removed old glass door panel (5 screws) then install new glass door panel from Appliance Pros. Read more