Need Help?
Call or text
Distributes gas evenly through burner ports on gas cooktops and ranges. Replace if cracked, clogged, or worn to restore uniform flame distribution.
Replace all 6 covers. Read more
Fix uneven oven heating or no convection baking with this range convection fan motor. Circulates hot air for consistent temperature throughout the cavity.
Fix clicking noise, poor cooling, or overheating compressor by replacing a cracked or warped condenser fan blade. Restores airflow across the coil.
At first, I thought that it was the defrost timer, but when I took apart the freezer, I found that the evaporator fan motor wasn't running, so I replaced it. Read more
Orifice holder aligns and channels gas from the valve to the burner on gas cooktops and ranges. Replace if cracked, damaged, or rusted for stable flame.
Ordered a replacement holder with a new ceramic igniter and installed it. The new unit would not quite fit correctly on the Metal stand. It took only a couple of minutes with a large file to remove some of the metal on each side of the metal prongs that locate the holder onto the stand. Once done, it was an easy assembly job and works just fine. Note: I ordered two of the Torx screws along with the holder and discovered this is a necessity since the old stainless screws have a barrel... Read more
Replaces a damaged, missing, or incorrect LP bake burner orifice in gas ranges. Essential for propane conversion to meter gas properly to the oven.
Pulled the old orifices and submitted a question about the proper replacements for my model. received a prompt reply with links to the correct parts. Added them to my cart and purchased, they arrived soon after and installed easily. Hooked up the range and it works perfectly. Read more
Surface burner cap sits on top of the gas burner head to shape the flame. Replace if yours is missing, chipped, cracked, or warped for proper appearance.
Husband did that. Found a burner cap kit. Said it was simple. Read more
This contact spade is a push-on electrical terminal used to connect an appliance wire lead to a component's blade. Replacing a worn or heat-damaged connector restores a secure fit and consistent power flow.
Full disassembly of removable tray into top plate (stainless) and lower pan taking care not to loose fasteners. Removal of terminal blocks using lubrication on rusted screws and, if necessary, drill out technique. Unclip wires from edges of the tray on both sides without losing the clips for future re-use. Top plate is now completely free of connections and may be cleaned/scrubbed separately in advance of re-assembly. Unfasten spade insulation block (located in the front of the tray) after... Read more
Black glass cooktop surface for electric ranges. Replaces cracked, broken, or damaged glass tops. Installs over heating elements with trim brackets.
VERY simple fix- you do not even have to pull the range out.. I ordered a new cooktop from Appliance parts Pros. The customer sales rep Alphonso was great and walked me through the general process. I could find no explicit instructions for the repair but I muddled my way through. The fix is simple on Kitchenaid/Whirpool slide in ranges. 1. Open the oven door and remove the two phillips head screws directly below the control panel that hold the panel down.2. Lift the control panel upward and... Read more
Distributes gas through ports to create an even cooking flame. Replace if cracked, clogged, or worn to restore proper ignition and consistent heat output.
Replaced all parts and range is working perfectly. Read more
Fix unresponsive controls, blinking displays, or oven won't heat. This electronic control board restores full function. Straightforward DIY install.
Replaced Control box, Very easy to install. Remember to DISCONNECT power cord. Read more
The burner orifice spud meters gas flow to your range's top burner. Replace worn, clogged, or incorrect orifices to restore proper flame output and combustion.
Changed out orifices in top burners. Read more
Secures the gas orifice and aligns it with the burner assembly on your gas range. Replace if cracked, damaged, or missing to restore proper gas flow path.
My Whirlpool range/oven needed to be converted from propane to natural gas. Appliance Parts Pros.com had the parts way cheaper than any local dealer. Doing this is not recommended for a novice as there are certain conversion specs that need to obtained and strictly followed. Read more
Safety bracket that secures your range to the floor to prevent tipping. Replace if missing, broken, or during new installation. Essential for homes with children.
Installed it according to video watched. Read more
Fix a burner that won't heat or has no temperature control by replacing this 6-inch element switch. Restores smooth low-to-high heat adjustment in 30 minutes.
Trial and error only cooktop unit. Everything mounted into the counter and needed to pull unit out. I figured it was a control switch or the burner itself. Based on costs, I took the less expensive route and replaced the 2 known malfunctioning switches. All on-line videos said it was a 2-3 hour process to replace. I finished mine in less than 30 minutes. Turned breaker back on and it works like a charm. 30 years old and still going strong. Read more
Controls gas flow to your range's top burner. Replace if the valve stem breaks, knob won't turn, or gas won't adjust properly for simmering or boiling.
I searched on your website for a replacement stem. Unfortunately the stem is not sold separately. I purchased the entire valve after confirming with your online rep that I was ordering the correct part. I received the valve in 2 days removed the stem and inserted it directly into the existing burner valve. Perfect fit easy installation and burner works as it should. Simply repair and I probably saved $100 by not calling a repair tech to come to my home. Read more
Color: Black. Measures about 2 inches in diameter. For biscuit use WP98008208. For white use WP98006102. Sold individually.
Ordered the parts from you and it's good now thanks for thinking of future use. Read more