Whirlpool Refrigerator Door

Restore a tight, even seal between your refrigerator's doors. This vertical mullion assembly flips into place to cover the center gap, helping maintain proper temperatures and reduce condensation.

• Bridges the gap between doors to create a continuous sealing surface
• Helps keep cold air in and warm air out for consistent cooling
• Aids proper door alignment and smooth closing
• Common symptoms of a failed mullion: broken or wobbly flipper, doors not closing fully or popping open, moisture/icing at the center, warming in the fresh food section

• Disconnect power before servicing and open the doors
• With the door open, release the retaining screws or tabs and lift the old mullion off the upper and lower pivots
• Position the new assembly on the pivots, secure it, and verify the flipper moves freely and seals evenly against the opposite door
• Restore power and recheck door operation and gasket contact along the full height

This ice compartment door closes off the ice storage area inside the freezer, helping contain cold air and keep ice clean. Replace a cracked or warped door to restore a proper seal and easy access to the bin.

• Covers the ice compartment opening to help maintain temperature around the ice bin
• Hinged panel provides convenient access to the ice container
• Helps minimize frost and moisture at the compartment opening
• Common signs it's needed: cracked/missing door, broken hinge tabs, won't stay closed, frost buildup, or ice clumping near the opening

• Disconnect power to the refrigerator before servicing
• Remove screws, pins, or clips securing the old door; note hinge orientation
• Transfer any reusable hinge pins, latches, or trim from the original if required
• Install and align the new door; confirm smooth operation and a tight closure

Color: clear. It measures about 12 inches wide by 6-1/2 inches high.

This door shelf trim is the front retainer bar that snaps across a refrigerator door bin to keep items in place. Replace a cracked or missing trim to restore secure storage on the door and prevent spills.

• Holds items within the door bin by providing the front retaining edge
• Common failure signs: cracked/broken bar, won't snap or stay in place, items sliding out of the bin
• Restores proper fit and appearance of the door shelf area

• Unplug the refrigerator before beginning any repair
• Lift off the affected door bin to access the trim
• Align the trim tabs with the bin slots and snap into place without forcing
• Verify the bin is seated securely on the door before use

This door trim is the decorative/protective molding that finishes the edge of the appliance door. Replacing damaged trim restores a clean appearance and a snug fit, helping reduce vibration noise and protecting exposed edges.

• Provides a finished, protective edge around the door
• Conceals fasteners and seams for a clean look
• Helps minimize rattles when properly secured
• Replace if cracked, warped, loose, discolored, or missing

• Disconnect power before servicing
• Open the door and note screw/clip locations; protect nearby surfaces with tape
• Carefully remove the old trim; transfer any clips/brackets from the original if applicable
• Align and secure the new trim; do not overtighten fasteners

This door mullion forms the pivoting center rail between the refrigerator's French doors. It flips closed to complete the door seal, helping prevent air leaks, condensation, and temperature swings in the fresh food section.

• Provides the center rail that bridges the gap when the doors close and flips open with either door
• Helps maintain a proper door seal to reduce warm air infiltration and moisture buildup
• Common signs of failure: broken or loose flap, won't flip or stay engaged, doors not closing evenly, condensation or frost near the center seal
• Restores smooth operation of the door stop and sealing surfaces

• Disconnect power before servicing
• Clear door bins and support the door to prevent strain while working
• Remove mounting screws/covers; note spring orientation and any clips on the old mullion
• Transfer hardware if needed, align and secure the new mullion, and verify it flips and seals smoothly

A vertical mullion assembly that restores the finished trim along the refrigerator door edge and covers the gap between doors for a clean appearance. Replaces cracked, broken, or loose mullion trim to improve fit and finish. What it does:

• Covers the vertical gap between refrigerator doors and provides a finished interior edge
• Hides and protects any wiring or fasteners routed along the door edge
• Restores proper door trim when the original mullion is cracked, split, or loose
• Helps reduce visible moisture or frost build-up along the door seam caused by damaged trim

• Disconnect power to the appliance before starting any repair to avoid injury
• Typically installs with a few fasteners or snaps into place; keep mounting screws from the original part if reusing
• Handle trim pieces carefully to avoid cracking; use non-marring tools to pry if needed

This door mullion is the vertical flipper rail that mounts to a refrigerator French door. It swings closed to cover the center gap, helping complete the door seal and reduce warm air leaks and condensation between the doors.

• Provides the pivoting center rail that mates with the opposite door to complete the seal
• Replace if cracked, broken, warped, or if the flipper won't fold or spring closed
• Common symptoms: door won't close smoothly, visible gap/light between doors, moisture or frost along the center seam
• Helps restore a proper air seal for consistent cooling performance

• Disconnect power and clear door bins before servicing
• Open the door; release the upper and lower retainers and lift the old mullion off its hinge points
• Position the new mullion, secure the retainers, and verify it pivots and seals correctly
• Check door alignment and gasket contact along the center seam

The Ice Door is an OEM component specifically designed for Whirlpool side-by-side refrigerators. Located at the top freezer compartment, it provides access to interior ice and water dispensing functions.  

Causes of a faulty ice door can include damage due to impact or warping from temperature fluctuations. Friction between the door seal and frame may prevent smooth opening and closing over time as well.

Symptoms of a bad ice door include:

• Difficulty opening or closing the door fully  
• Ice dispenser malfunctions or leakage occurs
• Seals no longer form an adequate barrier  
• Warping causes misalignments or binding

This OEM Whirlpool replacement ice door restores reliable access and sealing. Installed promptly to resolve any issues, it prevents further performance deterioration.  

Compatible also with some GE and Kenmore side-by-sides, this part maintains convenient dispensing functions. Protect your refrigerator investment with an OEM ice door replacement when needed.

This replacement lid fits the refrigerator utility/bin drawer and restores a secure cover to keep stored items contained and organized. It replaces cracked, broken or warped lids so the bin functions as intended. What it does:

• Covers and protects items stored in the utility/bin drawer
• Replaces lids that are cracked, chipped or no longer latch properly
• Helps prevent items from shifting or falling into other compartments
• Restores a proper seal and alignment of the utility/bin cover

• Unplug or disconnect power to the appliance before servicing for safety
• Remove the bin/drawer per the manufacturer instructions to access the lid
• Align hinge tabs or mounting points and snap or fasten the lid into place
• Handle carefully; plastic edges or mounting points can be fragile during installation

This mullion rail is the trim piece that secures and finishes the gap between refrigerator doors, improving seal alignment and giving the cabinet a clean, finished look. It restores proper door fit and appearance. What it does:

• Holds the mullion/trim in place along the door opening for a consistent seal and appearance
• Helps keep door gaskets aligned to reduce drafts and improve cooling consistency
• Prevents the trim from flexing or separating when doors are opened and closed
• Addresses visible trim damage, loose or missing mullion pieces, and uneven door gaps

• One mullion rail trim piece

• Disconnect power to the appliance before starting work to avoid injury
• Remove any door liners or screws that cover the mullion before replacing the rail
• Handle trim and clips carefully to avoid cracking; small retaining clips or screws may be reused if undamaged

Color: White

Note: This is a 2 door kit with both the Refrigerator and Freezer doors.

Color: Stainless
Note: This is a 2 door kit with both the Refrigerator and Freezer doors.
 

Color: Black

Note: This is a 2 door kit with both the Refrigerator and Freezer doors.