Whirlpool Washer Cap Or Cover

The Washplate Cap is an OEM part for Whirlpool washing machines. It serves as a protective cover for the central washplate, helping to keep debris and clothes from getting trapped in the washplate mechanism.

Causes of a bad washplate cap can include normal wear and tear, exposure to harsh laundry chemicals, or damage from heavy or unbalanced loads.

Symptoms of a bad washplate cap include:

• The cap not fitting securely on the washplate
• Visible cracks or damage
• Clothes getting snagged or trapped under the washplate

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This pulley cover encloses the drive belt and motor pulley at the base of the appliance. It protects moving parts from debris and contact, helping reduce noise and wear when the original cover is cracked, warped, or missing.

• Covers the drive belt and motor pulley to keep out dust and debris
• Helps prevent foreign objects from contacting moving parts
• Restores proper clearance to reduce rubbing or scraping noises
• Common signs it's needed: cracked/missing cover, rattling from the base, visible rub marks on the cover or belt

• Disconnect power and, if applicable, shut off water supply before servicing
• Access the underside per your service manual; support the unit securely if tilting
• Reuse existing mounting screws; do not overtighten to avoid damaging the plastic
• Rotate the belt/pulley by hand after installation to confirm free movement and no contact

The Rinse Aid Cap is an OEM part for Whirlpool dishwashers. It is designed to securely cover the rinse aid dispenser, ensuring the proper release of rinse aid during the wash cycle to improve drying performance and prevent water spots on dishes.

Causes of a bad rinse aid cap can include wear and tear over time, damage from accidental mishandling, or loss of the cap. Without a properly functioning cap, the rinse aid may not dispense correctly.

Symptoms of a bad rinse aid cap include:

• Rinse aid leaking or not dispensing
• Water spots or streaks on dishes after drying
• The cap not fitting securely or being visibly damaged
• The rinse aid compartment remaining full or not using rinse aid as expected

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This lid lock bezel is the plastic trim that mounts on the washer's top panel around the lid lock. It supports and protects the lock opening so the latch aligns correctly and the area looks clean and finished.

• Provides mounting/trim for the lid lock/switch assembly on the top panel
• Helps keep the lock aligned with the lid strike for reliable engagement
• Replaces cracked, broken, or missing bezel that leaves the lock loose or exposed
• Common signs include a loose or wobbly lock, difficulty latching the lid, or cosmetic damage around the lock opening

• Disconnect power and water supply before servicing
• Access the top panel (release spring clips or remove screws per model)
• Remove screws securing the lid lock, lift out the old bezel, position the new bezel, and reinstall the lock using existing fasteners
• Test operation before reassembly

The Coin Box is an OEM replacement part for Whirlpool combo washer/dryers. It provides a storage space for coins used to operate the unit. The coin box slots ensure collected change remains safe and secures payments for laundry cycles.

Causes of a bad coin box can be normal wear from hundreds of deposits, minerals clogging slots, or physical damage compromising security.

Symptoms of a bad coin box include:

• Coins not being accepted or properly collected
• Box distorting shape or developing cracks over time
• Change falling out or going missing

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

The Lid Lock Bezel (White) is an OEM replacement part for Whirlpool washers. The bezel provides an aesthetic covering for the lid lock mechanism located on top of the washer. 

Causes of a bad bezel can include normal wear and tear from repeated use of the washer lid over time. Scratches, cracks or splits in the plastic material are also possible from accidental impact or drops.

Symptoms of a bad bezel include:

• Cosmetic flaws like discoloration, scratches or cracks that diminish the appearance of the washer
• Looseness, rattling or misalignment of the bezel covering 
• Difficulty opening or closing the washer lid securely. 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

This replacement cap covers an opening or fastener on the appliance. It helps keep water, detergent, and debris out while restoring a clean, finished look and maintaining a secure fit. What it does:

• Covers and protects an exposed opening or fastener from moisture and debris
• Helps prevent residue from entering internal areas
• Restores the appliance's finished appearance
• Common signs of failure: missing cap, cracks, warping, or a cap that won't stay seated

• 1 cap

• Unplug the appliance; if working near water connections, turn off the water supply
• Carefully remove the old cap without prying against delicate surfaces
• Clean the mating area; align and press or twist the new cap until fully seated
• Verify a secure fit and normal operation

This cap is a small protective cover used in select appliances. It helps secure and seal its mating component, preventing leaks, debris intrusion, or loosening during normal operation.

• Maintains a secure seal/cover over the designated fitting or opening
• Helps prevent leaks and contamination in the covered area
• Can resolve issues like minor leaks, loose or missing cap, or rattling noises
• Restores proper fit and finish after the original cap is lost or damaged

• Disconnect power and shut off water or gas supply before servicing
• Note the orientation of the original cap for correct placement
• Hand-tighten only unless the OEM specifies otherwise; do not overtighten
• Inspect the mating surface or threads for damage before reinstalling

Restore the clean look and proper function of your washer's detergent compartment with this detergent dispenser drawer cover. It replaces a cracked or missing cover so the drawer closes correctly and helps reduce splashing at the dispenser. What it does:

• Covers and protects the front of the detergent dispenser drawer
• Helps the drawer align and close properly for consistent dispensing
• Replaces broken or missing cover tabs that prevent the drawer from staying in place
• Common symptoms: cracked/missing cover, broken tabs, drawer won't close or feels loose, splashing/leaks at the dispenser area

• 1 detergent dispenser drawer cover

• Unplug the appliance and shut off water supply before servicing
• Pull the dispenser drawer out and depress the release tab to remove it
• Release the locking tabs to remove the old cover; snap the new cover fully into place
• Reinstall the drawer and run a quick test to check operation

The Bezel is an OEM component for Whirlpool washing machines. Situated at the front base, this decorative surround frames the appliance opening. 

Precision die-cut for a seamless fit, durable composite material stands up to splashes and bumps while retaining a pristine finish. Integrated mounting feet anchor solidly for years of use.

Causes of a faulty bezel can include fading paint from chemical exposure or developing stress cracks from impacts over an extended service period. 

Symptoms of damage include:

• Chipped edges compromising structural integrity   
• Peeling or flaking paint finish diminishing aesthetics
• Gaps along seams allowing intrusion of moisture 
• Mounting brackets corroding from mineral deposits

Replace yours today with this genuine Whirlpool bezel to restore like-new curb appeal. Also compatible with some Maytag, Amana, and Roper models.

The Lid is an OEM part for Whirlpool washing machines. This part provides a secure closure for the washing machine's top. This lid ensures that the washing process occurs without spillage or interruption, maintaining the efficiency and safety of the washing cycle.

Causes of a bad lid can include physical damage such as cracks or breaks, wear and tear on hinges or locking mechanisms, and electrical faults in the lid switch or sensor that prevent the washing machine from recognizing when the lid is closed.

Symptoms of a bad lid include:

• The washing machine fails to start or stops mid-cycle.
• Visible damage or warping of the lid.
• Problems with the lid locking or sealing correctly.
• The machine displays error codes related to the lid or lid switch.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models, ensuring a broad range of applications for repair or replacement needs.

This is a replacement access cover that protects internal components and restores the appliance's finished appearance. It keeps wiring and service areas shielded while providing a neat exterior finish. What it does:

• Covers and protects exposed internal components and wiring from dust and debris
• Restores the appliance's exterior appearance where the original cover was cracked, broken, or missing
• Helps keep service areas clean and prevents accidental contact with non-serviceable parts
• Fits into the existing mounting points to secure panels and trim

• One replacement access cover

• Disconnect power to the appliance before beginning any service
• Remove fasteners or clips holding the old cover; preserve hardware if reuse is intended
• Align the new cover with factory mounting points and secure with the original screws or clips

This access panel cover protects internal components and provides a finished appearance for your appliance. It replaces a cracked, broken, or missing cover to help keep wiring and parts shielded from debris and accidental contact. What it does

• Covers and protects internal parts behind the control or service area
• Restores the appliance's finished exterior where the original cover was damaged
• Helps prevent debris buildup and accidental contact with internal components
• Can reduce rattling or vibration caused by a loose or broken cover

• Disconnect power (unplug appliance or switch off breaker) before attempting repair
• Basic hand tools are typically required; follow the service manual for removal and installation steps
• Handle edges carefully; some covers may have sharp edges
• Tighten fasteners securely but avoid overtightening to prevent cracking