Whirlpool Washer Dispenser Parts

This dispenser handle assembly restores proper operation and control of your refrigerator's ice and water dispenser. It replaces a cracked, loose, or broken handle so you can dispense without difficulty and improve the dispenser's appearance. What it does

• Replaces damaged or cracked dispenser handle so the lever engages properly
• Provides a secure grip for activating the ice and water dispenser
• Helps stop wobbling or sticking that prevents consistent dispensing
• Restores alignment and tactile feedback for dispenser operation

• Disconnect power to the refrigerator before starting any work to avoid electrical hazard.
• Remove the old handle by accessing the dispenser trim and fasteners; retain mounting screws if reusing.
• Align the new handle, secure fasteners, and verify the dispenser lever moves freely and dispenses correctly.

This dispenser is the exterior door component that delivers chilled water and/or ice from the refrigerator, restoring normal dispensing and preventing drips or jams. It replaces a damaged, cracked or non-functioning door dispenser. What it does

• Guides water and ice from the internal plumbing to the exterior spout so items can be dispensed from the door.
• Re-establishes a secure spout and actuator for reliable dispensing and reduced leaks.
• Stops common dispenser symptoms such as leaking at the door, stuck or loose dispenser lever, and misaligned spout.
• Helps restore normal dispensing when the door dispenser is cracked, broken, or no longer seating properly.

• One dispenser assembly.

• Disconnect power and shut off the refrigerator water supply before beginning.
• Remove the interior door panel and any trim to access the dispenser assembly; keep fasteners organized for reassembly.
• Inspect and replace any worn gaskets or seals to prevent leaks; ensure proper hose routing.
• Test operation and check for leaks after reconnecting power and water.

The Door Latch is an OEM part for Whirlpool washers. It ensures that the washer door locks securely during operation, preventing leaks and ensuring that the washer will not operate unless the door is properly closed. This latch is crucial for the safety and efficiency of the washing cycle.

Causes of a bad door latch can include wear and tear from frequent use, physical damage from slamming the door, or electrical issues that prevent the latch from locking or unlocking correctly. A malfunctioning latch can interrupt the wash cycle and compromise safety.

Symptoms of a bad Door Latch include:

• The washer door not locking or unlocking
• The washer not starting or stopping mid-cycle
• Error codes related to door lock issues
• Difficulty in opening or closing the door

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Dispenser Tray is an OEM part for Whirlpool top-loading washing machines. Located inside the detergent drawer, this durable molded tray is designed to hold liquid detergent packs safely in place during cycles. Its size and dimensions facilitate convenient single-dose placement.

Causes for replacement may include cracks, warping, or discoloration due to mineral buildup affecting the tray structure over time.

Symptoms of a faulty tray involve:  

• Difficulty loading or securing detergent packs properly   
• Leaks or spills of detergent inside the drawer compartment
• Off-center or displaced detergent dosing during the wash

This OEM Whirlpool replacement is compatible with select Whirlpool, Maytag, and other major brand front-loaders.

The Detergent Dispenser Drawer is an OEM part for Whirlpool washing machines. It plays a crucial role in dispensing detergent during the wash cycle. The drawer is designed to hold and release the appropriate amount of detergent at the right time, ensuring optimal cleaning performance. 

Symptoms of a bad dispenser drawer include:

• Improper dispensing of detergent  
• Insufficient cleaning results
• Leaks or drips from the dispenser area
• The drawer not opening or closing correctly

Causes of a bad dispenser drawer can include clogging or blockage in the drawer mechanism, damage to the drawer or latch, or malfunctioning electronic components that control the dispensing process. 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Dispenser Drawer Assembly is an OEM part for Whirlpool front-loading washing machines. The drawer houses mechanisms that deposit detergent and fabric softener into the drum at the proper times in the wash cycle. 

Causes of a bad dispenser drawer can include wear and tear to runners, rollers, or linkage connecting it to the washer cabinet over repeated use. Mineral or chemical deposits may also jam drawer movement.

Symptoms of a bad dispenser drawer include: 

• Failure to fully retract or extend from the cabinet
• Difficulty latching or staying securely closed  
• Contents not fully dispensing into the drum
• Inconsistent or improper distribution of detergent

This OEM Whirlpool replacement drawer assembly is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore front-loading washing machines. 

Color: Grey

The Tank is an OEM part for Whirlpool washing machines. It properly dispenses detergent during the wash cycle.

Causes of a bad detergent tank can include: cracks, holes or other damage that cause leakage or improper detergent dispensing. Scaling or mineral buildup inside the tank over time may also lead to detergent dispensing issues.

Symptoms of a bad detergent tank include:

• Detergent not being fully dispensed or released during the wash
• Residue or leftover detergent remaining in the tank after cycles
• Clothes not getting properly cleaned due to insufficient detergent release

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This dispenser drawer holds and guides detergent, bleach, and fabric softener into the washer at the correct cycle time. Replacing a worn drawer helps prevent leaks, residue buildup, and improper dispensing that can affect wash results.

• Channels detergent, bleach, and softener from the 3-compartment tray into the wash
• May help when detergent remains in the drawer, leaks from the tray, or additives dispense inconsistently
• Restores smooth opening/closing and proper alignment of the dispenser tray

• Unplug the appliance and shut off water supply before servicing
• Pull the drawer out and release the locking tab to remove; reverse to install
• Transfer any reusable inserts from the old drawer if applicable
• Check for residue in the dispenser housing and clean before reinstalling

This dispenser drawer slides into the washer's dispenser housing and holds detergent and laundry additives for each cycle. Replace a cracked, stuck, or missing drawer to restore smooth operation and proper dispensing. What it does:

• Holds and organizes detergent and other laundry additives in labeled compartments
• Works with the dispenser housing to flush products into the tub at the correct time
• Helps contain liquids to reduce drips and spills around the dispenser area
• Typical failure symptoms: cracked/broken face or tabs, drawer binding or popping out, detergent left in the drawer, or water leaking at the dispenser

• 1 dispenser drawer

• Disconnect power and turn off water before servicing
• Fully extend the old drawer, press the release tab, and pull it free from the housing
• Move over any removable siphons or inserts from the old drawer if present
• Slide the new drawer in until it latches and glides smoothly; run a quick test cycle to check dispensing and leaks

The Dispenser Drawer is an OEM part for Whirlpool washing machines. It is responsible for properly dispensing the correct amount of laundry detergent at the appropriate time in the wash cycle. The detergent dispenser drawer is specifically designed to hold laundry detergent pods or liquid in its molded compartments.

Causes of a damaged detergent dispenser drawer can include corrosion or degraded plastic parts over time caused by repeated exposure to laundry detergents.

Symptoms of a malfunctioning dispenser drawer include:

• Improper dispensing or no dispensing of detergent during wash cycles
• Residue buildup or leaks from the dispenser area
• Drawer not opening or closing securely as intended
• Dispenser components broken, cracked, or non-functional

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This funnel directs liquid fabric softener and bleach from the dispenser into the wash tub to ensure proper dispensing and reduce splashing. Fits into the washer dispenser assembly to restore correct chemical flow during cycles. What it does:

• Channels liquid fabric softener and liquid bleach from the dispenser to the wash tub
• Prevents splashing and spilling inside the dispenser area
• Helps ensure timed delivery of additives during the correct cycle
• Commonly replaced when the funnel is cracked, clogged, or missing

• One fabric softener and bleach fill funnel

• Disconnect power to the washer before servicing to avoid shock or injury
• Remove the dispenser or control console as required to access and snap the funnel into place
• Inspect surrounding dispenser components and gaskets; replace if damaged
• No special tools required for most installations.

This dispenser assembly mounts in the refrigerator door to provide a stable dispensing point for ice and water and restore normal use of the door dispenser. It replaces damaged or worn dispenser components to stop leaks and restore proper operation. What it does:

• Provides the exterior opening and actuator area for dispensing ice and/or water
• Guides and supports the dispense lever or actuator and related components
• Helps prevent leaks and dripping from the door dispense area
• Commonly replaced when the dispenser won't actuate, leaks, or has broken trim or lever

• Disconnect power and shut off the water supply before starting
• Door panel or inner liner removal may be required for access
• Handle trim and plastic parts carefully to avoid cracking during removal/installation
• Follow the refrigerator's service manual or tech sheet for torque and routing details

The Dispenser Drawer is an OEM component specifically designed for Whirlpool washing machines. It provides a contained area to safely add detergent and fabric softener during wash cycles.  

Symptoms of a bad dispenser drawer include:

• Inability to open or close smoothly
• Cracks or breaks in the plastic housing
• Leaks or spills from seals no longer fully containing liquids

Causes can relate to mineral buildup corroding moving parts, cracks developing from repeated opening/closing, or impact issues distorting the structural integrity of the design.

Color: Chrome Shadow

This OEM replacement dispenser drawer is designed to directly replace the worn original. Compatible models include those from brands such as Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore. 

The Washer Detergent Container is an OEM replacement part for Whirlpool washers. It fits securely inside the dispenser drawer and is compartmentalized to hold detergent, fabric softener, and bleach. This container ensures the proper distribution of each cleaning agent during the wash cycle for optimal cleaning performance.

Over time, the detergent container may deteriorate due to exposure to chemicals, high temperatures, or buildup of residue, leading to potential leaks, blockages, or compromised distribution of cleaning agents.

Color: White

Symptoms of a faulty Washer Detergent Container include:

• Leaks from the dispenser drawer
• Clogged or restricted compartments
• Inconsistent or improper dispensing of detergent, fabric softener, or bleach

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This dispenser housing assembly holds the dispenser components and guides water or ice from the refrigerator door to the user. It restores a secure, leak-resistant dispensing point and corrects visible housing damage. What it does:

• Replaces a cracked, broken, or worn dispenser housing to stop leaks and prevent debris entry
• Supports the dispenser actuators and channels water or ice toward the dispenser opening
• Helps restore normal dispensing action when the door dispenser is loose or misaligned
• Can reduce rattling or binding caused by a damaged housing

• Disconnect power and water supply before beginning service to avoid shock or flooding
• Remove the door liner or access panel to access fasteners and wiring
• Handle trim and actuator pieces carefully to avoid cracking; reuse gaskets/seals only if undamaged
• If electrical connectors or switches are involved, verify connections and test function before reassembling