Whirlpool Washer Dispenser Parts

This dishwasher detergent dispenser stores detergent and releases it at the correct time in the cycle for consistent cleaning results. Replacing a worn dispenser restores reliable dosing so each wash performs as designed. What it does:

• Holds detergent and keeps it contained until dispensing
• Opens the detergent cup door at the programmed time in the cycle
• Directs detergent into the wash stream for even distribution
• Helps prevent poor cleaning caused by early loss or failure to dispense

• 1 detergent dispenser assembly

• Disconnect power and turn off water supply before servicing
• Remove the inner door panel to access the dispenser; support wiring and insulation as you work
• Release mounting tabs/screws, transfer the wiring connector, seat the new dispenser evenly, and tighten fasteners uniformly
• Run a quick cycle to check for leaks

This bleach dispenser stores liquid chlorine bleach and automatically dilutes and releases it at the correct point in the wash cycle. Replacing a cracked or clogged dispenser helps stop leaks, protect fabrics, and restore consistent bleaching performance.

• Holds bleach and siphons it into the tub at the proper time in the cycle
• Helps prevent undiluted bleach from contacting fabrics early
• Direct replacement for a dispenser that is cracked, warped, or clogged
• Address symptoms such as bleach remaining in the cup, dispensing too soon, leaks near the dispenser area, or fabric spotting

• Disconnect power and turn off water before servicing
• Access the dispenser through the top/console area; remove fasteners and detach connected hose(s)
• Transfer any hoses, clamps, and mounting hardware from the original part; ensure all connections are fully seated to prevent leaks
• Run a test/rinse cycle to check for leaks

This door-mounted dispenser stores detergent and rinse aid and releases them at the right time in the cycle to help deliver clean, spot-free dishes. Replace a broken, leaking, or jammed dispenser to restore proper detergent release.

• Holds detergent and rinse aid and dispenses them during the wash cycle
• Supports consistent cleaning performance by timing chemical release
• Detergent cup won't latch or open
• Rinse aid doesn't dispense or leaks from the dispenser
• Detergent remains in the cup after the cycle

• Disconnect power and turn off the water supply before servicing
• Remove the inner door panel to access the dispenser
• Disconnect the wire harness, release locking tabs/fasteners, and install the new unit flush to the door
• Clean the sealing surface; tighten fasteners evenly and run a test cycle to check for leaks and proper dispensing

This is a replacement refrigerator storage drawer. It restores smooth sliding and dependable storage when the original drawer is cracked, warped, or missing, helping you keep items organized and easy to access. What it does

• Provides enclosed storage for food items inside the refrigerator
• Slides on the existing rails for easy access and organization
• Helps keep contents visible and separated from other items
• Common failure symptoms: cracks, broken tabs, drawer falling off tracks, hard to open/close

• 1 drawer

• Disconnect power and remove items from the drawer area before starting
• Fully extend and lift to remove the old drawer; clean the tracks
• Align the new drawer with both rails and slide it in evenly
• Do not force; ensure tabs and tracks are properly seated

This is the siphon insert for the washer dispenser's bleach and softener compartments. It restores proper siphoning so additives empty at the right time and helps reduce standing water or residue in the drawer.

• Creates the siphon action that draws bleach and fabric softener from their cups during the rinse cycle
• Promotes complete dispensing and consistent rinse performance
• Helps minimize leftover liquid and residue buildup in the dispenser
• Typical symptoms include bleach or softener remaining after the cycle, standing water in the cups, or weak/irregular dispensing

• Disconnect power and turn off water before servicing
• Remove the dispenser drawer; lift out the old siphon from the bleach/softener cup
• Clean any debris in the cup; firmly seat the new siphon, aligned per the cup markings
• Reinstall the drawer and run a rinse cycle to verify proper draw and no leaks

This dispenser handle assembly replaces a broken, loose, or missing handle on your appliance's dispenser. It restores a solid grip and proper actuation so the dispenser opens or operates smoothly and looks clean again.

• Provides the user grip/actuator for the dispenser mechanism
• Enables smooth opening or activation of the dispenser
• Helps ensure consistent operation and a clean finished look
• Common symptoms: cracked or missing handle, loose/wobbly handle, hard-to-open dispenser, handle won't stay attached

• Disconnect power; if working near water lines, shut off the water supply
• Open access to the dispenser area; retain and reuse any mounting screws/clips
• Transfer any reusable trim or small parts from the old handle if applicable
• Align and secure the new handle; test operation before reassembly

Color: White

The Dispenser Drawer Assembly is an OEM component specifically designed for Whirlpool washers. It houses detergent and fabric softener during cycles.

Causes of a faulty assembly can include warping of the plastic base from heat and chemicals over many loads. Small cracks may develop in the detergent trays.  

Symptoms of a bad dispenser drawer assembly include: 

• Leaks from cracked or misaligned drawers polluting washer interiors  
• Difficulty closing or securing the assembly properly
• Premature deterioration inhibiting reliable cycles 

This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models.

This replacement drawer restores a clean, organized storage space inside your refrigerator. It provides a smooth, secure place to hold items so you can access contents easily and maintain the appliance's intended capacity and layout. What it does

• Slides on factory rails/guides to organize food and contain spills
• Restores lost storage capacity when the original drawer is damaged or missing
• Helps contents stay properly supported and easy to access
• Common symptoms: cracked/broken bin, hard-to-slide or misaligned drawer, drawer falls out

• One drawer

• Power down the appliance if working near lights/fans; wear cut-resistant gloves
• Remove items, then lift and pull the old drawer straight out
• Inspect and clear/repair rails or guides before installing the new drawer
• Align with the tracks and slide in until fully seated; do not force

This replacement dispenser drawer restores smooth operation and proper dispensing of detergent, bleach, and fabric softener in your washer. It helps prevent leaks and residue when the original drawer is cracked, warped, or difficult to open and close. What it does:

• Holds and meters detergent, bleach, and fabric softener into the wash at the correct time
• Helps ensure additives mix with water and flow into the tub, not onto the cabinet front
• Direct replacement for drawers with broken handles, cracks, or swelling
• Common symptoms: leaking at the drawer area, poor dispensing, leftover detergent, or a stuck drawer

• Includes: 1 dispenser drawer assembly

• Disconnect power and turn off water before servicing
• Pull the drawer out fully and depress the release tab to remove
• Transfer any removable siphon caps or inserts from the old drawer
• Clean the dispenser housing channels, then slide in the new drawer and run a test cycle to check for leaks

Keep your batch-feed disposer operating safely and easily. This actuator handle inserts into the sink opening to start and stop the disposer and also functions as the sink stopper on batch-feed models, replacing cracked, worn, or missing handles.

• Engages the internal switch to start/stop the disposer when inserted and rotated
• Provides a secure grip for controlled batch-feed operation
• Helps seal the drain to hold water in the sink between uses
• Symptoms include: disposer won't run or runs intermittently with the handle inserted, handle is cracked/loose, or won't lock/turn to engage

• Disconnect power to the disposer before testing or handling parts
• Ensure the sink opening and splash guard are clear so the handle seats fully
• Insert the handle into the drain, align/press down, and rotate per your owner's manual to engage; reverse to stop
• Never place hands inside the disposer; use tongs/pliers to remove objects

This dishwasher dispenser stores detergent and rinse aid and releases them at the correct points in the cycle to support consistent cleaning results. Replace a broken, stuck, or leaking dispenser to restore reliable detergent delivery.

• Holds detergent and rinse aid and dispenses them automatically during the wash and rinse portions of the cycle
• Door/actuator mechanism controls the timed release of detergent
• Seals help prevent leaks around the dispenser opening
• Typical failure symptoms: detergent cup won't latch or open, detergent left in the cup, rinse aid not dispensing, or leaks from the dispenser area

• Disconnect power and turn off water supply before servicing
• Remove the inner door panel to access the dispenser; disconnect the wire connector
• Release mounting screws/clips, clean the door cutout, and seat the new dispenser evenly
• Tighten screws in a cross pattern to compress the gasket uniformly; run a test cycle to check for leaks and proper operation

The Dispenser Drawer Handle is an OEM part for Whirlpool washing machines. The white handle allows users to easily access the detergent dispenser drawer at the beginning of the wash cycle. 

Causes of a bad handle can include worn or stripped mounting areas that no longer provide a stable grip, cracks or breaks in the plastic material, or missing/damaged spring components that assist in closing the drawer. 

Symptoms of a bad handle include:

• Difficulty opening the dispenser drawer 
• The handle no longer stays securely in place when opening the drawer
• Inability to fully open or close the dispenser drawer

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This is the pull-out dispenser drawer assembly for a washer. It holds and channels laundry products into the dispenser housing so each additive is released at the right time, restoring smooth operation and proper dispensing. What it does:

• Holds detergent and additives and directs them into the wash at the correct stage
• Restores smooth open/close action of a worn or broken drawer
• Helps resolve issues like detergent remaining in the drawer after a cycle
• Addresses leaks or drips from a cracked or warped dispenser drawer

• 1 dispenser drawer assembly

• Unplug the washer and turn off water supply before servicing
• Pull the old drawer out; depress the locking tab(s) to remove
• Transfer any reusable inserts/caps from the original drawer if applicable
• Slide the new drawer into the rails until it clicks; run a quick cycle to check for proper dispensing and leaks

The Divider is an OEM part for Whirlpool washers. It fits within the dispenser drawer, creating separate compartments for different laundry products such as detergent, fabric softener, and bleach. It prevents mixing and allows for convenient dispensing during each wash cycle.

A bad dispenser drawer divider can occur due to wear and tear over time or accidental damage. If you notice symptoms such as a loose or broken divider, difficulty in separating the compartments, or improper dispensing of laundry products, it may be time to replace this part.

Symptoms of a bad dispenser drawer divider include:

• Loose or broken divider
• Difficulty in separating the compartments
• Improper dispensing of laundry products

Restore your Whirlpool washer's dispenser drawer by replacing the faulty or damaged divider with this genuine OEM part.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

The Dispenser Drawer Handle is an OEM part compatible with Whirlpool washers. It provides a convenient grip for opening and closing the dispenser drawer. It allows you to access the detergent, fabric softener, and bleach compartments within the dispenser drawer.

A bad dispenser drawer handle can occur due to wear and tear, accidental damage, or excessive force when operating the handle. If you notice symptoms such as a loose or broken handle, difficulty in opening or closing the dispenser drawer, or the handle not staying securely in place, it may be time to replace this part.

Symptoms of a bad dispenser drawer handle include:

• Loose or broken handle
• Difficulty in opening or closing the dispenser drawer
• Handle not staying securely in place

Restore your Whirlpool washer's dispenser drawer by replacing the faulty or damaged handle with this genuine OEM part.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This outer trim panel cover replaces a cracked, broken or missing exterior cover to protect internal components and restore the appliance's finished appearance. It fits where the factory cover shields wiring and mounting points. What it does:

• Protects wiring, switches and internal parts from debris and accidental contact
• Restores the appliance's exterior finish and prevents drafts or gaps
• Stops rattling or vibration caused by damaged or loose trim
• Helps keep moisture and dust out of sensitive areas

• Disconnect power to the appliance before starting any repair.
• Remove any adjacent panels or fasteners to access the cover; retain screws and clips for reassembly.
• Align cover tabs and secure with original screws or clips; do not force or overtighten to avoid cracking.
• Replace those parts before finishing the repair.