Whirlpool Washer Hinge Parts

A hinge pin assembly that secures and aligns an appliance door to its cabinet, restoring proper fit and smooth opening and closing while reducing hinge noise. What it does:

• Secures the door pivot and maintains proper door alignment for a consistent seal.
• Can correct door sag, uneven gaps, or doors that stick, scrape, or fail to close fully.
• Can reduce grinding, clicking, or binding noises caused by worn or bent hinge pins.
• Replaces worn, broken, or bent hinge components that affect door motion.

• Disconnect power to the appliance before beginning any repair.
• Support the door (use a helper or suitable block) to prevent it from dropping when removing the hinge.
• Basic hand tools are typically required; follow the manufacturer's service instructions for safe removal and reinstallation.
• Inspect adjacent hinge mounts and fasteners during installation; replace damaged mounting hardware as needed.

Washer lid hinge attaches the lid to the cabinet, allowing smooth opening and closing. Replace if cracked, rusted, broken, or causing lid misalignment.

This replacement hinge supports and guides the appliance door for smooth opening and closing, restoring proper alignment and helping the door seal correctly. Ideal when a worn hinge causes sagging, noise, or improper latching. What it does:

• Provides a secure pivot point so the door opens and closes smoothly.
• Keeps the door aligned to maintain a proper seal and prevent gaps.
• Reduces hinge noise, scraping, or binding during door movement.
• Common symptom indicators: door sagging, door doesn't stay closed, uneven gap, or noisy operation.

• Disconnect power (and water, if applicable) before starting any repair.
• Support the door while removing or installing the hinge to prevent the door from falling.
• Use the correct hand tools; snug fasteners securely but avoid overtightening.

Right-hand lid hinge for top load washers. Secures and guides the lid for smooth opening and closing. Replace if cracked, corroded, or broken.

This hinge guide is the small bushing the hinge pin rides in. It reduces friction and keeps the panel aligned so the door or lid opens smoothly and closes flush for reliable everyday use.

• Provides a low-friction bearing surface for the hinge pin
• Helps maintain door/lid alignment so it closes flush
• Wear can lead to sagging, scraping, squeaking, or binding
• Restores smooth operation and consistent closing when the original is worn

• Disconnect power; shut off water supply
• Support the door or lid before loosening hinge fasteners
• Remove the worn guide and install the new guide on the hinge pin or in the hinge bracket
• Reassemble, then check alignment and smooth open/close

This door hinge replaces a worn or damaged refrigerator door pivot to restore smooth opening and secure door alignment. It provides a stable mounting point so doors open and close without sagging or binding. What it does:

• Supports the refrigerator door and keeps it aligned on the cabinet
• Enables smooth pivoting action for opening and closing the door
• Commonly used to fix door sag, sticking, rubbing, or uneven gaps
• Works with original mounting hardware locations to maintain correct seal

• Unplug the appliance or disconnect power before starting work
• Remove food and secure the door; have a helper support the door during removal/installation
• Use basic hand tools; avoid over-tightening fasteners to prevent damage
• Check door alignment after installation and adjust as needed for a proper seal

This replacement refrigerator door hinge keeps the door aligned and operating smoothly so your appliance seals and closes properly. It restores proper door movement and helps prevent drafts and uneven wear. What it does:

• Supports the refrigerator door and maintains correct alignment for a tight seal
• Allows smooth opening and closing of the door without binding
• Helps prevent door sag, rubbing, or gaps that can cause temperature issues
• Fits where the original hinge mounts to the cabinet or door depending on model

• Disconnect power and remove contents from the door before starting work
• Support the door while removing and installing the hinge to prevent dropping or damage
• Use the original fasteners or OEM-recommended hardware; tighten screws securely but avoid over-torquing

Replaces a cracked, bent, or broken washer door hinge. Secures the door and ensures smooth pivoting action. Essential for proper door alignment.

This hinge secures and guides a refrigerator door on its pivot, helping the door open and close smoothly while maintaining proper alignment and seal. It's a direct-fit replacement when the original hinge is worn or damaged. What it does:

• Replaces a worn or broken door pivot to restore proper door movement and alignment
• Prevents sagging or binding that can stop the door from closing fully
• Helps maintain an effective door seal to protect cooling performance
• Works as the mechanical mounting point between the door and cabinet

• Basic hand tools are typically required; support the door while removing and installing the hinge
• Follow manufacturer guidance for torque and alignment; adjust door leveling as needed after installation
• Disconnect power and remove contents from the door if required for safe handling

Replacement lid hinge for top-load washers. Attaches the lid to the cabinet, allowing smooth opening and closing. Order a new hinge if yours is cracked or broken.

Replace your washer's hinge when cracked, broken, or worn. This structural component supports the lid or door assembly during opening and closing.

Replacement washer lid hinge that connects and supports the top lid. Needed when the existing hinge is cracked, broken, or no longer holds the lid properly.

Secures and guides your washer door for smooth opening and closing. Replace when the hinge is cracked, broken, or worn, causing door misalignment or sagging.