Yard Machines Blade

This scraper blade is an authentic OEM replacement part for a snowblower. Snowblowers operate using an auger that scoops up the snow and blows it to a different location. However, an auger cannot gather all of the snow because it would have to scrape against the ground. Scraping that auger against the ground would damage its blades and make them unusable. Instead, this scraper blade drags against the ground and collects any remaining snow so that the auger blades can remain protected. Scraper blades can be damaged if the snowblower goes over rocky terrain. Although it is nearly impossible for a blade to snap completely off a blower, the blade will leave the snow behind, making the blower less effective if chipped or dented. To replace a scraper blade, simply use a socket wrench to unbolt the blade from the auger housing. Be sure not to lose the bolts as they will be needed for reassembly. This part is compatible with Craftsman, MTD, Cub Cadet, Ryobi, Huskee, Yard Man, and Yard Machines snowblowers and is sourced from the original manufacturer. This part is a high-quality replacement part. It does not ship with additional hardware.

These quality tiller tines are used on a variety of yard tillers. Tiller tines are blades attached to the tiller that turn soil and prep it for cultivating a garden. As the tiller tines are used, they can become worn down, broken, or damaged through use or impact with rocks and other debris. These are C-shaped tines that can cut through dense soil.If the tiller tines are bent, dull, or damaged, they will need to be replaced, otherwise they might till the soil unevenly and may not reach the depth required. To replace the tines, remove the spark plug wire before taking off the tine shield end cover. Taking out the tines requires removing the cotter pin from the clevis pin so the clevis pin can be pulled out. Next, the tines can be pulled directly off of the shaft. Slide on the new tines and reinstall the clevis and cotter pins before using the tiller again.These tiller tines are an authentic OEM replacement part directly sourced from the manufacturer. It is sold as an individual part. The tines are compatible with tillers manufactured by MasterCut, Craftsman, Yard-Man, Cub Cadet, Bolens, Yard Machines, MTD, Huskee, and Montgomery Wards.

This blade adapter kit secures the blade of the lawnmower to the spindle shaft. It's used on walk-behind lawnmowers and is made of durable metal. The kit is sold as an individual item but comes with the blade bolt, the adapter, and the bell blade support. Over time, these parts can wear out or become damaged and will require replacement.The only tool needed for the replacement is a socket set. Remove the spark plug wire and hold the blade while wearing gloves. Take off the blade bolt and support, followed by the blade. Attach the new parts to the lawnmower and reassemble the other components.This is a genuine OEM replacement part that is sourced directly from the manufacturer. The blade adapter kit is sold as an individual component. It is made for use with lawnmowers manufactured by Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, MTD, Huskee, Montgomery Wards, Bolen, Yard-Man, and MasterCut.

This genuine MTD shredder screen determines the size of the shreds that the wood chipper will produce. A shredder screen covers any number of shapes and sizes of screens through which the wood will be chipped.A shredder screen might have to be replaced in the event that it suffers damage over time or in the case that the wood chipper encounters wood that is too hard or too brittle, which can break the shredder screen. The bars of a shredder screen can be welded back into shape by hand, but it is easier and safer to order a replacement shredder screen if it is subject to breaking, piercing, puncturing, or erosion to the metal material. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This shredder screen is compatible with the following brands: MTD, Cub Cadet, Yard Machines, Yard-Man, Craftsman, and Troy-Bilt. This part is sold individually.

This genuine MTD shave plate, also known as a scraper bar, can be used as a replacement part for snowblowers. The shave plate is located at the bottom of the auger to scrape snow off of surfaces and filter it into the auger of the snowblower.Damage to the shave plate might include cracks, dents, and erosion to the metal material, or it can gradually wear out and no longer be effective. Evidence of a cracked shave plate can come from a visual inspection, but it can also be detected if the snowblower is doing a poor job of collecting and scraping snow off of surfaces. A cracked shave plate should be removed and replaced immediately, and a snowblower should not be used before the part is replaced. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This shave plate is compatible with the following brands: MTD, Yard Machines, Cub Cadet, Yard Man, and Craftsman. Part sold individually.

This left-hand inner tines assembly sit next to the outer tines on the left side of tillers from a variety of major manufacturers. The tines are the part of the equipment that breaks up the soil to create a garden and allow cultivation. The part is made of strong metal, but over time it can start to wear down or break when running over large rocks or other items.If the tines are broken or have been worn down, they will need to be replaced. Tines that are worn will not dig into the earth as well as new tines. A hammer and a set of pliers are required to make the replacement. Remove the tines from the tiller after turning it off and taking out the spark plug wire. The new tines can be installed in the same place.These inner tines are made to be used with tillers created by MasterCut, Yard-Man, Bolens, Montgomery Wards, Huskee, MTD, Yard Machines, Cub Cadet, and Craftsman. It is sold as an individual part. This is a genuine OEM replacement part that is sourced directly from the manufacturer.

These outer tines are used on lawn equipment to help dig up the earth for gardening or other purposes. They are made of durable metal but may wear down after being used. The tines can also crack or break in some cases. When the tines have worn down or become damaged, they will need to be replaced.Take a look at each set of tines on the tiller to see how much they have worn down since being purchased. If they are half the size they were when new, they need to be replaced. The process of replacing the tines is simple and requires nothing more than work gloves and pliers. Use the pliers to remove the outer tines from the tiller so they can be removed. Install the new tines with the pins and the equipment will be ready to use.These outer tines are a genuine OEM replacement part that are directly sourced from the manufacturer. The tines are sold individually. They are made for use with tillers manufactured by MasterCut, Yard-Man, Bolens, Montgomery Wards, Huskee, MTD, Yard Machines, Cub Cadet, and Craftsman.

This lawn mower outer tine assembly is for lawnmowers. Tines are used for dethatching the lawn, which can be useful in the spring. The outer tine is attached to the inner tine.Tines may become damaged with regular use or sudden impact, as with hitting rocks or cement. Damage might present itself as chips in the metal, bending, or a full break. A damaged tine should be replaced right away. Otherwise, the equipment will not function properly and could be dangerous. A screwdriver or a pair of pliers will be needed to properly install the new tine.The metal outer tine assembly works as a replacement part for many brands of lawnmowers. Compatible brands include MTD, Yard Machines, Bolens, Yard-Man, Cub Cadet, Husky, and Troy-Bilt. The OEM part is sourced directly from the manufacturer and is sold as an individual replacement.

This part is a shave plate. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a damaged, detached, or worn shave plate on certain models of snowblower. When using a snowblower, stubborn or stuck pieces of snow can affect proper functionality. Shave plates attach to the underside of the snowblower to help scoop stubborn snow or slush into the auger housing. Over time, as they regularly scrape the ground, shave plates will become worn and will no longer make sufficient contact with the pavement. In order to ensure snow blowers continue to do their job efficiently, shave plates should be replaced once they exhibit signs of deterioration. Proper tools are needed to replace this part and appropriate safety guideline should always be adhered to.As an authentic replacement part, this shave plate can be used on multiple different models of snow blowers manufactured by Cub Cadet, Craftsman, Huskee, Troy-Bilt, Yard-Man, and MTD. Please note that this shave plate is a genuine part made of high-quality, durable materials and is sold individually.

This chipper blade is an authentic OEM replacement part sourced directly from the manufacturer for use in chipper shredders. The blade is the workhorse of the machine, chopping the limbs and sticks into tiny particles as they pass through the machine. As the machine is used, the blades will become dull and need sharpened. Eventually, the blades may develop cracks or become so worn that they need to be replaced for the chipper to function efficiently. Chipper blades should be periodically inspected.Wear safety gear and remove the chipper's spark plug before working on the blades. Remove the bolts holding the hopper in place and set the bolts and hopper aside. Remove the housing protecting the rotor assembly and chipper blades. Remove the bolts holding the chipper blades in place. Discard the old blades. Install the new blades and reassemble the chipper. Put the spark plug back in and test the blades.This chipper blade is made of heavy-duty metal and is sold as an individual part. It does not include connecting bolts. This blade is designed for use in chippers manufactured by MTD and Troy-Bilt.

This is a chipper impeller assembly that can be used with a range of chippers and chipper-shredders. The impeller is the part of the chipper that rotates, and it is what allows for the chipping or shredding to take place. It will shred leaves, yard waste, and tree limbs. If there is an issue with the chipper impeller, it will reduce the efficiency of the machine. In some cases, it might not work at all. One of the signs that the impeller has problems is that it is turning slowly. It might also make a lot of noise.The impeller is a durable piece, but it does a lot of work. This means it is subject to wear and tear. Over time, it might become worn out or damaged, which will require a replacement. This replacement could be done by the owner. However, they need to remove the spark plug wire first and wear gloves to keep their hands safe.The chipper impeller assembly works for select machines from MTD, Troy-Bilt, Husky, and Yard Machines. This is a genuine OEM replacement part sourced from the manufacturer, and it is sold individually.