Parts for Whirlpool CB19G7B13: 02 - Freezer Liner Parts

Seals refrigerator or freezer door to prevent air leaks and maintain temperature. Replace if torn, deformed, or door won't close tightly. Confirm fit.

Replace your refrigerator's fill tube guide if cracked, broken, or missing. This plastic guide sleeve directs the water fill tube in your ice maker assembly.

Freezer cold but fridge warm? Your evaporator fan motor circulates air between compartments. Most DIYers complete this repair in 1 hour with our video.

Freezer or fridge light not working even with a new bulb? This light socket provides the electrical connection. Basic DIY repair with video guide.

Freezer not cooling or running constantly? This mechanical temperature control thermostat regulates freezer temps. DIY-friendly repair in under an hour.

Fix dim or no interior lighting with this refrigerator light bulb. Restores clear visibility when you open the door. Simple 5-minute replacement.

This outer cabinet housing provides a durable structural shell that supports internal components and protects them from debris and wear. It restores proper alignment and enclosure for safe, stable appliance operation. What it does:

• Replaces a cracked, dented, or misshapen outer housing that can allow debris or moisture into the appliance
• Restores proper mounting surfaces and clearances for panels, controls, and internal assemblies
• Helps reduce rattling or vibration caused by a compromised cabinet
• Prevents exposure of internal wiring and components to contaminants

• One outer cabinet housing

• Recommended for experienced DIYers; some disassembly of panels and components is required
• Disconnect power and any water lines before beginning work
• Keep track of screws and brackets; some fasteners may be reused

This replacement screw secures specified refrigerator components—such as covers, brackets, and internal panels—so they stay properly mounted. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and reliable operation.

• Provides the correct fastener for locations identified in your model's parts diagram
• Helps prevent looseness, vibration, and rattling of panels or brackets
• Replace if the head is stripped, threads are worn, or the screw is missing
• Symptoms can include loose parts, gaps, or noises from movement

• Unplug the refrigerator and shut off water if working near the ice maker or dispenser
• Match length and type to the original; follow your model's parts diagram for placement
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing, especially into plastic
• Keep track of screw positions; do not mix different screw lengths or styles

The refrigerator fan motor grommet is a small rubber cushion that mounts between the evaporator or condenser fan motor and its bracket, absorbing vibration during motor operation. It reduces noise and prevents the motor's vibration from transferring to the refrigerator cabinet. Replace this part if your refrigerator is making a rattling or buzzing noise coming from the fan area, which is often caused by a worn or deteriorated grommet.

Freezer not cooling properly or frosting over? This control module regulates temperature and defrost cycles. Restores proper freezer operation.

Secures panels, trim, and wire harnesses in your refrigerator to reduce vibration and rattling. Replace when clips break or parts become loose. Confirm fit with your model number before ordering.

Interior lights staying on or not working? This door switch controls refrigerator lighting and functions. Moderate DIY repair with video guide available.

Water pooling in freezer or fridge? A clogged or cracked defrost drain funnel causes leaks. DIY fix in 30-45 minutes by accessing the rear freezer panel.

Creates a watertight seal at water connections to prevent leaks. Replace when cracked, flattened, or worn. Confirm fit with your model number.

This is a flexible rubber seal that attaches around the perimeter of the refrigerator door. It creates an airtight seal when the door is closed to maintain proper internal temperature and prevent warm air from entering. Replace this gasket if you notice condensation forming around the door edges, the refrigerator running constantly, or if the seal is torn, cracked, or no longer holding the door closed tightly.

Seals the drain tube connection to prevent leaks and ice buildup in your freezer. Replace if you see water pooling or ice forming at the freezer bottom.

This is a plastic vent grille that covers the air intake or exhaust area on the refrigerator, typically located at the bottom front or top of the unit. It allows airflow to the condenser while keeping debris out. Replace this grille if it is cracked, broken, discolored, or if missing louvers are restricting proper ventilation and causing the refrigerator to run warm.

Protective housing that covers refrigerator fan components. Replace if cracked or broken to ensure proper airflow and protection. Confirm fit with model.

Loud noise or freezer warming up? This evaporator fan blade circulates cold air over coils. Simple DIY fix—most repairs done in under an hour.

Freezer temperature control knob mounts on the control shaft inside your refrigerator. Replace yours if cracked, worn, or missing to restore grip.

Right-hand slide bracket secures drawer or shelf slide assemblies in refrigerators. Replace if cracked, broken, or causing misalignment issues.

Left-side slide bracket that secures and guides drawer assemblies in refrigerators. Replaces worn, cracked, or broken brackets to restore alignment.

This replacement screw secures panels, brackets, and components inside appliances. Replacing a missing or stripped fastener restores a snug, rattle-free fit using the correct #8-18 thread and 5/8-inch length.

• Fastens covers, trims, brackets, and internal parts to the cabinet/frame
• Used wherever a #8-18 x 5/8 screw is specified
• Replace if the original is missing, corroded, stripped, or will not tighten
• Symptoms: loose or rattling panels, gaps, or hardware that backs out

• Disconnect power; shut off gas/water before servicing
• Match thread and length; start by hand to avoid cross-threading
• Use the correct driver bit and tighten snugly—do not overtighten
• Inspect and replace damaged clips or tabs before securing

Support bracket that holds the freezer basket in position and allows it to slide smoothly. Replace if cracked, broken, or basket won't stay aligned.

Supports and secures the freezer basket in proper position for smooth sliding. Replace if cracked, broken, or missing to restore basket alignment.

Extends and retracts freezer drawer in bottom-mount refrigerators. Replace if the spring broke, plastic tab cracked, or drawer won't close properly.

NOTE:  This is a set of 2 slides.

Mounting bracket for refrigerators. Secures components in place inside the cabinet. Replace if bent, cracked, or broken to restore proper support.

Size: 8 x 1-1/4 inch.

Repair kit for refrigerator drawer slide mechanisms. Includes gears and rod to replace stripped, broken, or missing components in pull-out drawer rails.