Parts for Maytag 1DNET3205TQ0: 06 - Washer Top And Lid Parts

Color: White

These lid bumpers are sold individually.

The Washer Lid Screw is an OEM part for Whirlpool washing machines. This 6-32 x .340 screw secures the washer lid to the hinge assembly, ensuring the lid opens and closes smoothly and stays securely in place during operation.

Causes of a bad washer lid screw can include wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or mishandling. A compromised screw can lead to issues with the lid's stability and functionality.

Symptoms of a bad washer lid screw include:

• The washer lid feeling loose or wobbling
• Difficulty in opening or closing the lid
• Visible rust or corrosion on the screw
• The lid not staying securely in place

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Specs: 10-16 x 1/2 inch.

This screw grommet anchors a screw in thin appliance panels so trim, covers, or consoles stay tight. It provides a snug, vibration-damping fit where a standard screw could loosen or strip over time.

• Creates a captive insert so a screw can securely fasten to sheet metal or plastic panels
• Replaces a worn, cracked, or missing grommet to restore proper screw retention
• Helps reduce panel rattles and movement from vibration
• Typical signs of failure: screw won't tighten, panel or trim feels loose, grommet falls out

• Disconnect power and shut off gas/water as applicable before servicing
• Remove the screw and lift out the old grommet; clear debris from the opening
• Press the new grommet straight into the hole until fully seated and flush
• Reinstall the screw and tighten gently to avoid deforming the grommet

This replacement clamp secures flexible hoses and lines to prevent leaks and keep connections tight. It restores a secure seal so appliances move water or air without escaping at the joint. What it does:

• Secures inlet, drain or water lines to fittings and housings
• Helps stop leaks from loose or worn hose connections
• Keeps hoses from slipping off during operation or vibration
• Commonly replaced when clamps are corroded, broken, or no longer hold tension

• Inspect hose and fitting for damage before installing the new clamp
• Position clamp over the hose barb and tighten evenly until snug; avoid over-tightening
• Use appropriate tools (pliers or clamp driver) and follow appliance safety procedures
• Disconnect power and shut off water supply when working on water lines

This lid retainer assembly secures and aligns the washer lid to the cabinet, restoring proper lid engagement and reducing movement or rattling during use. It helps the lid close and latch reliably for normal operation. What it does:

• Secures the washer lid to the cabinet and keeps the lid aligned.
• Helps the lid engage properly with the latch so cycles can start as intended.
• Minimizes lid movement and vibration that can cause noise during spin.
• Replace if cracked, broken, or missing — common causes of lid misalignment, rattling, or a lid that won't stay closed.

• Disconnect power to the appliance before beginning any service.
• Basic hand tools required; your model's service diagram or manual for exact removal/installation steps.
• Inspect adjacent parts (hinge, strike, lid) while installing and replace if damaged.

The lid hinge bearing is used for the lid hinges on washers and dryers. When functioning properly, it allows the lid to open and close properly. If this is a problem with the bearing, it could make the lid difficult to move. In some cases, when the lid will not close, it means that the machine will not function correctly. Damaged lid hinge bearings should be replaced as soon as possible.The lid hinge bearings see a lot of work since they are in use whenever the lid of the washer or dryer opens and closes. They could become cracked and broken over time. Replacing the bearings is a relatively simple repair that owners can make on their own.This lid hinge bearing is for use with many models of washers and dryers from Whirlpool, KitchenAid, Roper, Estate, Inglis, Maytag, Admiral, Amana, Crosley, and Magic Chef. This is a genuine OEM replacement part that has been sourced from the manufacturer. The piece is sold individually, so if owners need to replace more than one hinge, they will need to buy multiples.

This screw and washer is an OEM replacement part used for Whirlpool washers. It is used to secure the lid switch. Each screw is sold individually. The screw measures approximately 1 inch.

The Lid Strike is an OEM part for Whirlpool washing machines. This small yet essential component ensures that the washer lid is securely latched, allowing the machine to operate safely and effectively. The lid strike interacts with the lid switch, enabling the washer to detect when the lid is closed and allowing the washing cycle to proceed.

Over time, the lid strike can become worn out or damaged due to regular use, accidental force, or misalignment. A faulty lid strike can prevent the washing machine from recognizing that the lid is closed, thereby hindering the operation of the machine.

Symptoms of a bad lid strike include:

• The washer not starting or stopping mid-cycle
• Error messages indicating the lid is open when it is closed
• Difficulty in latching the lid securely
• The lid strike appearing broken or misaligned

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This right-side door hinge rebuilds a worn or damaged pivot point so the appliance door opens, closes and seals properly. It restores door alignment and prevents sagging that can cause gaps and cooling loss. What it does

• Replaces the right-side door pivot to restore correct door swing and alignment
• Reduces door sag and helps maintain an even seal to improve temperature retention
• Stops rubbing, scraping or binding that can occur with a worn hinge
• Works with the existing hinge housing and fasteners when used as a direct replacement

• One right-side door hinge (single hinge)

• Install with power to the appliance off and interior removed as needed for safe access
• Support the door during replacement to prevent dropping or additional damage
• Use the OEM fasteners and torque to manufacturer recommendations; inspect surrounding parts for wear

This left-side door hinge restores correct door support and movement so the appliance door opens and closes smoothly. It replaces a worn or bent hinge that can cause sagging, misalignment, or noisy operation. What it does:

• Supports the left side of the appliance door and maintains proper alignment
• Enables smooth, controlled opening and closing of the door
• Replaces a bent or broken hinge that causes door sag or rubbing
• Helps prevent gaps that can affect door sealing or operation

• Disconnect power (or unplug) and remove any panels as instructed by the manufacturer before starting
• Support the door during removal and installation to prevent injury or damage
• Use proper tools and follow the appliance service manual for torque and fastener locations

The Lid Switch is an OEM part for Whirlpool washing machines. The lid switch is located beneath the washer's lid and is activated when the lid is closed. It acts as a safety feature, preventing the washer from operating when the lid is open. When the lid is closed, the lid switch engages and signals to the washer's control system that it is safe to proceed with the wash cycle.

Causes of a faulty lid switch can include wear and tear, electrical issues, or damage from excessive force or impact.

Symptoms of a bad lid switch in a washer may include:

• Washer not starting or responding to controls
• Washer stopping or pausing mid-cycle when the lid is opened
• No spin or agitation during the wash cycle

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Used from harness to top.