Parts for Maytag MAH14PDABL: 08 - Outer Tub Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

Includes ball bearing, rear bearing, water deflector, hose clamp, spacer, motor isolator, plug & Lip Seal

Specs: No.8X1/2 HEX WASHER HEAD

The OEM Replacement is a bearing designed to function as the rear bearing in Whirlpool front-load washers. It also works as the upper brake bearing in top-load washers. Positioned near the tub's brake assembly, this component plays a significant role in the operation of the washer. In top-load washers, it resides above the brake assembly.

Causes of a bad bearing can include prolonged wear and tear, exposure to excessive loads, or water intrusion that leads to rust and corrosion. A compromised bearing can lead to more significant issues if not addressed promptly.

Symptoms of a bad bearing include:

• Loud, unusual noises during the wash or spin cycles
• Excessive vibration or movement of the washer
• The drum not rotating smoothly or becoming stuck
• Leaks around the drum area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This injector hose is a direct-fit replacement that routes water between dispenser and injector assemblies to restore proper water flow and prevent leaks. It's a straightforward part for repairing water delivery issues in compatible appliances. What it does:

• Carries water from the valve/dispenser to the injector or dispensing assembly
• Prevents leaks when intact; degraded or cracked hoses can drip or spray
• Helps restore proper dispensing when damaged hoses cause poor water delivery
• Common symptom link: visible leaking, water pooling, or dispenser not filling as expected

• One replacement injector hose

• Disconnect power and shut off the water supply before starting any repair
• Inspect fittings and clamps; replace clamps or O-rings if worn
• Push hose fully onto mating fittings and secure with proper clamps to prevent leaks

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose

This is a genuine replacement screw used to secure appliance panels and components, restoring proper fit and reducing vibration or rattling. Simple, low-cost fastener that helps keep parts aligned and stable. What it does:

• Fastens panels, brackets, or trim to the appliance frame
• Restores secure connections that can cause buzzing, rattling, or loose trim
• Replaces missing or stripped hardware to prevent further movement or wear
• Works where the original OEM screw was specified for fit and compatibility

• Disconnect power before working on electrical appliances to avoid shock
• Use the correct size driver to avoid stripping the head
• Install by hand initially to ensure proper threading, then snug—do not overtighten
• Retain removed hardware and compare to the new screw for correct fit before final assembly

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This tub displacement switch monitors water level/pressure to help the washer detect tub fill and balance, reducing overfill and load sensing errors. It replaces a worn or faulty unit to restore reliable fill and balance sensing. What it does:

• Senses tub water displacement/pressure changes so the washer can detect correct fill and load balance
• Helps prevent overfilling and supports proper spin cycles by reporting tub condition to the control
• Commonly replaced when washer overfills, won't start spin, or shows erratic fill behavior

• Disconnect power before accessing internal components to avoid shock
• Mounts to the washer chassis with electrical connector and vacuum/pressure hose; reuse existing hose if undamaged
• Verify hose and fittings are intact and free of blockages before installation

This is a genuine replacement screw used to secure appliance panels and components, restoring proper fit and reducing vibration or rattling. Simple, low-cost fastener that helps keep parts aligned and stable. What it does:

• Fastens panels, brackets, or trim to the appliance frame
• Restores secure connections that can cause buzzing, rattling, or loose trim
• Replaces missing or stripped hardware to prevent further movement or wear
• Works where the original OEM screw was specified for fit and compatibility

• Disconnect power before working on electrical appliances to avoid shock
• Use the correct size driver to avoid stripping the head
• Install by hand initially to ensure proper threading, then snug—do not overtighten
• Retain removed hardware and compare to the new screw for correct fit before final assembly

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement airdome hose restores the pressure/air connection used by the appliance's water/air sensing system, helping maintain proper cycle control and preventing response issues caused by a damaged or cracked hose. What it does

• Transfers air/pressure between the airdome and sensor or control assembly to enable accurate water-level or vent sensing.
• Prevents false readings or erratic cycles that can occur when the hose is cracked, pinched, or disconnected.
• Restores an airtight path so controls can respond correctly during fill and drain operations.
• Helps reduce the risk of overflow, extended cycles, or no-start symptoms related to pressure-sensing faults.

• One airdome hose (single replacement hose as pictured)

• Turn off power and water to the appliance before attempting service.
• Inspect connection ends for matching fit; trim or replace clamps only if specified by the manufacturer.
• Reconnect securely to both fittings and check for pinches or kinks that could affect function.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

This 2-pack of dryer vent clamps secures the vent hose to the dryer outlet and the wall/vent hood. A tight connection helps maintain airflow, reduce lint leaks, and keep the duct from slipping off during use.

• Tightens around the vent hose to hold it securely to the dryer exhaust collar or exterior vent
• Helps prevent hose detachment, air leaks, and lint escaping at the connection
• Supports proper exhaust airflow by keeping connections sealed and stable
• Common symptoms pointing to replacement: hose won't stay on, visible gaps or lint around fittings, rattling at the vent, or longer dry times from poor ventilation

• Disconnect power; for gas dryers, shut off gas supply before moving the appliance
• Slide a clamp over the hose, seat the hose fully on the collar, position clamp over the fitting, and tighten with a screwdriver or nut driver
• Do not overtighten; avoid crushing thin foil ducting; ensure the hose is straight and not kinked
• Restore power and verify strong airflow at the exterior exhaust

This bolt-style retaining screw secures appliance panels and components to prevent movement and rattling. A small but critical fastener that restores proper fit and reduces noise from loose parts. What it does:

• Fastens and secures panels, brackets, or assemblies in place
• Stops rattling or vibration caused by a missing or loose screw
• Restores proper alignment of the attached component
• Matches OEM fit and thread pattern for a secure hold

• Disconnect power and unplug the appliance before beginning any work
• Use the correct screwdriver or socket to avoid stripping the head
• Thread carefully and do not overtighten to prevent damage to threads or plastic parts
• Keep small parts away from children and work on a clean, well-lit surface

This 1-1/4" washer is a replacement flat washer used to secure fasteners and distribute load for reliable appliance assembly. It helps maintain proper clamping and prevents bolt/nut damage for stable operation. What it does:

• Sits under a nut or bolt head to spread load and protect mating surfaces
• Prevents fastener loosening caused by vibration or movement
• Reduces wear between joined parts to extend component life
• Helps maintain correct alignment of assemblies where used

• Turn off and unplug the appliance before beginning any repair
• Match this washer to the original by size and thickness to ensure a proper fit
• Use appropriate hand tools and replace any corroded or damaged fasteners at the same time

Pulley, spinner restores proper spinner rotation by guiding the spinner assembly and maintaining belt alignment. Replacing a worn or damaged pulley reduces noise and vibration during spin and helps improve water extraction. What it does:

• Guides and supports the washer's spinner assembly for smooth rotation and correct belt tracking.
• Common symptoms of a failing pulley: loud squealing or grinding during spin, wobbling spinner, belt slippage, or poor water extraction.
• Replaces a worn, cracked or noisy pulley to restore normal spin performance.

• Disconnect power (unplug or switch off breaker) and shut off water before servicing.
• Access the spinner area per your appliance's service guide—remove panels or agitator as needed to reach the pulley.
• Inspect belt, bearings and mounting hardware; replace any worn or damaged components at the same time.
• Follow manufacturer torque and reassembly instructions.

The Belt and Isolator Kit is an OEM part for Whirlpool washing machines. This kit includes a drive belt and isolators that work together to transfer motion from the motor to the washer drum while dampening vibrations. 

Over time, the belt can wear out, stretch, or break due to regular use, heavy loads, or friction. The isolators may also deteriorate, losing their ability to absorb shocks effectively.

Symptoms of a bad Belt and Isolator Kit include:

• The drum not spinning or agitating
• Excessive vibration or noise during operation
• The washer failing to start or complete cycles

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.