Parts for Maytag LSE7800AEE: 12 - Motor & Pump (Lse7800ace,Ade,Aee) Parts

This factory screw secures appliance components such as panels, brackets, and trim. It replaces missing, stripped, or damaged hardware to restore a tight, rattle-free fit and proper alignment in the specified location for your model.

• Fastens covers, panels, brackets, or trim as specified in the parts diagram
• Restores secure fit when an original screw is missing or damaged
• Helps reduce vibration, rattling, and looseness
• Direct-fit hardware specified by the manufacturer for the original location

• Disconnect power and shut off water/gas before servicing
• Verify the screw's location in your model's parts diagram before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver/bit and avoid overtightening into plastic to prevent stripping

This part has been discontinued by the manufacturer and is no longer available.

The Washer Drive Motor is an OEM part for Whirlpool washing machines, designed to convert electrical energy into mechanical motion to drive the washing machine drum. This motor is a pivotal component in ensuring your washer operates smoothly across various cycles, whether it's agitating clothes in the wash cycle or spinning them dry. 

Causes of a bad Washer Drive Motor can range from wear and tear over time, overheating due to overloading or obstructed movement, and electrical failures such as short circuits or damaged wiring.

Symptoms of a failing Washer Drive Motor include:

• The washer not agitating or spinning correctly
• A burning smell or unusual noises during operation
• The washing machine failing to start

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This factory spring kit restores the designed tension and return action in the affected assembly so moving parts operate smoothly, stay in position, and wear evenly over time.

• Provides the correct counterforce to position or balance components
• Maintains steady tension to prevent drift, slamming, or misalignment
• Helps reduce squeaks, chatter, or uneven movement from fatigued springs
• Typical signs of failure: weak return, inconsistent movement, excess noise, or visible spring damage

• Disconnect power; shut off water or gas before servicing
• Wear eye protection—springs are under tension
• Note original spring anchor points and replace all springs in the kit as a set
• Use appropriate pliers or a hook tool; verify smooth operation before reassembly

The Motor Mount Roller and Spring Kit is an OEM part for Whirlpool washing machines. This kit includes the motor mount, roller, and spring, which work together to support and stabilize the motor during the wash and spin cycles. These components are crucial for minimizing vibrations and ensuring the motor runs smoothly and efficiently.

Causes of a bad motor mount, roller, or spring can include normal wear and tear over time, heavy or unbalanced loads that put extra stress on the components, and accidental damage or impact. 

Symptoms of a bad motor mount, roller, or spring include:

• Excessive noise during the wash or spin cycle
• Vibrations or shaking of the washing machine
• The drum not spinning properly
• Motor misalignment or poor performance

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Motor Mount Roller and Spring Kit is an OEM part for Whirlpool washing machines. This kit includes the motor mount, roller, and spring, which work together to support and stabilize the motor during the wash and spin cycles. These components are crucial for minimizing vibrations and ensuring the motor runs smoothly and efficiently.

Causes of a bad motor mount, roller, or spring can include normal wear and tear over time, heavy or unbalanced loads that put extra stress on the components, and accidental damage or impact. 

Symptoms of a bad motor mount, roller, or spring include:

• Excessive noise during the wash or spin cycle
• Vibrations or shaking of the washing machine
• The drum not spinning properly
• Motor misalignment or poor performance

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Size: 10-32

The Drain Hose is an OEM part for Whirlpool washing machines. It is responsible for carrying wastewater from the washing machine to the household drain system, ensuring proper removal of water during and after the wash cycle.

Common causes of a bad drain hose include wear and tear over time, blockages from debris or lint, and damage from sharp objects or improper installation.

Symptoms of a bad Drain Hose include:

• Water leaks from the hose
• Slow or incomplete drainage
• Visible cracks, splits, or punctures
• Unpleasant odors from trapped debris

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Washer Drain Pump is an OEM part for Whirlpool washing machines. It is responsible for removing water from the washing machine during the drain cycle, ensuring efficient and complete water removal.

Causes of a bad drain pump can include blockages from debris or foreign objects, electrical failures, or wear and tear from regular use. Over time, these issues can impede the pump's ability to function properly.

Symptoms of a bad drain pump include:

• Water not draining from the washer
• Unusual noises during the drain cycle
• Error codes related to draining issues
• Leaks coming from the pump area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: Fits 2 belt design Maytag washers. Check belts for wear; if needed order 12112425.

This factory fastener secures appliance components such as panels, brackets, and trim. Replacing a missing or stripped screw restores a tight fit, reduces rattling, and helps keep assemblies aligned for reliable performance.

• Fastens appliance parts to maintain structural integrity and alignment
• Helps address symptoms like loose or vibrating panels, gaps, or hardware that won't stay tight
• Replaces lost, damaged, or corroded fasteners during repairs or reassembly
• OEM-matched thread and fit for the specified location

• Disconnect power; shut off gas or water supplies before servicing
• Replace one screw at a time to preserve alignment of parts
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing
• Use the correct driver size/type specified for your model

This hex-head screw secures the bearing insert in place, maintaining correct alignment and stable operation. Replacing a damaged or missing screw restores secure bearing retention and reduces noise or wobble. What it does:

• Holds the bearing insert assembly firmly to prevent movement and misalignment
• Helps stop excessive vibration, noise, or drum wobble caused by a loose bearing insert
• Maintains correct spacing so the bearing and shaft rotate smoothly
• Replaces stripped, rusted, or missing fastening hardware for reliable operation

• Unplug the appliance or disconnect power before beginning any repair
• Use the proper hex driver and size to avoid stripping the head
• Tighten securely but do not overtighten; overtightening can deform the insert or housing
• Inspect the bearing insert and surrounding parts; replace any damaged components for a lasting repair

This hose clamp secures a flexible hose to its fitting to help prevent leaks and hose blow-offs during operation. Replace a rusted, stripped, or distorted clamp to restore a tight, reliable seal at the connection point.

• Applies clamping force around a hose to hold it on a barb or stub fitting
• Commonly used on washer drain and tub-to-pump hose connections
• Helps stop drips at the joint and prevents the hose from slipping off
• Typical failure signs: leaking at the connection, clamp won't tighten, visible rust, broken/warped band

• Unplug the appliance and turn off water supply; expect some residual water
• Seat the hose fully on the fitting; place the clamp just behind the bead/barb
• Tighten until snug and secure; do not overtighten to avoid damaging the hose
• Run a short test cycle and recheck for leaks at the connection

The Tub to Pump Hose is an OEM part for Whirlpool washing machines. This hose connects the tub to the pump, allowing water to drain from the tub during the washing and rinsing cycles. It is designed to handle the water flow and pressure within the washer, ensuring efficient drainage.

Causes of a bad tub to pump hose can include wear and tear over time, exposure to harsh chemicals or debris, or damage due to accidental punctures or kinks. When the hose is compromised, it can lead to drainage issues and potential water leaks.

Symptoms of a bad tub to pump hose include:

• Water not draining from the washer
•  Leaks or puddles underneath the washer
• Visible cracks or wear on the hose
• Error codes related to drainage problems

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Motor Mount Roller and Spring Kit is an OEM part for Whirlpool washing machines. This kit includes the motor mount, roller, and spring, which work together to support and stabilize the motor during the wash and spin cycles. These components are crucial for minimizing vibrations and ensuring the motor runs smoothly and efficiently.

Causes of a bad motor mount, roller, or spring can include normal wear and tear over time, heavy or unbalanced loads that put extra stress on the components, and accidental damage or impact. 

Symptoms of a bad motor mount, roller, or spring include:

• Excessive noise during the wash or spin cycle
• Vibrations or shaking of the washing machine
• The drum not spinning properly
• Motor misalignment or poor performance

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.