Randall B Moab , UT January 14, 2017 Appliance: Maytag Dishwasher MDB6800AWW There were two problems one of the spring links on the door broke which meant the door would free fall when opened unless you held on to it also the lower bearing on the motor virtually seized up I first wanted to get the dishwasher running, before ordering the spring links. So I disassembled the pump / motor assembly to determine the reason the motor would not start. My wife cleaned all of the parts in the pump assembly. I took the motor apart and discovered that the lower bearing ( a sleeve type bearing) was dry and dirty, and was the culprit for the motor seizing. I cleaned up the bearing and lubricated it with SAE 20W. I also packed felt inside the cavity adjacent to the bearing. and saturated it with 20W. I reassembled the motor / pump assembly and installed it in the dishwasher. I noticed that the seal (part #902882 which is located under the drain impeller), was slightly damaged. I was also concerned that the pump to tub gasket had also had better days. However I put the dishwasher back into service. It worked just fine, with the exception of water leaking around the motor shaft during the 3 drain cycles. I was thankful for the rubber shaft boot located above the splash plates. It prevented the water from getting into the electric motor. I placed a Tupperware tub under each end of the splash plates. I had to empty them after each drain cycle. So, when it was time to run the dishwasher, I had to remove the lower access panel and monitor the water level of the tubs. I received the spring links, so after the second run, I replaced both links. This entailed unhooking the water supply, taking the two screws that secure the dishwasher to the counter, and pulling the dishwasher out far enough to reinstall the spring that had the broken link. I went ahead and changed out the "good link" (now a spare) with a new one. The door now, works like new and doesn't free fall when opened. By the way, our dishwasher is a Maytag model MDB6800AWW, and has been in service for about 18 years. My wife loves how well it cleans our dishes. Unfortunately, many of the repair parts to keep it running are unavailable, including the motor, relay, and even the seal below the drain impeller. I was able to buy a used pump / motor assembly from e-bay, to use for parts. I'm still trying to find another seal #902882. I've tried a lot of parts houses (including Sears) with no avail. However, after the third run, I was happy to see that only a tablespoon of water had leaked out from the drain assembly. I appreciate the prompt service in getting the parts which I can still procure. I have completed Penn Foster's appliance repair course, and like the challenge of repairing my and my family's appliances. The repair on the dishwasher, was a great learning experience. I hope to gain enough expertise to have the confidence to repair appliances on a part time basis, for a little additional income. Again, thanks for your professional service. Sincerely, Randall G. Bowden Read More... 5 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 2+ hours Tools: Adjustable Wrench, Nut Drivers, Pliers, Screwdrivers, Socket Set, Wrench Set
George T Naples , FL September 27, 2014 Appliance: Model YOU LOOK AT MY ORDER Heard a loud bang and thought a door spring on my 20 year old maytag dishwasher had broken Without knowing exactly what broke I ordered 2 springs and 2 door spring links. I knew the door springs were weak and a parts man told me many years ago to always replace BOTH springs or the one you didn't replace will soon break. It is a simple procedure, just remember how the springs/links are attached. make a simple drawing or take a picture should you need it. I watched two "how to" video's which made it look harder to do than it really is. Turn the circuit breaker off and turn the dishwasher on to make sure it is turned off. I did not unhook anything since I was only pulling the washer out 6-8 inches which was enough to replace the springs and links. The hardest part is cleaning up the dirt you will find when you take the kick panel off. It's simple...you can do it. Tony Trapp Naples, Florida Read More... 24 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Screwdrivers
Adem A San Jose , CA October 22, 2014 Door droping on to floor The dishwasher door was dropping on to the kitchen floor when opened. I realized that the door spring is on the floor. The plastic piece holding the spring was broken. It was easy to replace it after watching the video from the Appliance Pros Website. Read More... 5 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Pliers, Screwdrivers
John M Sykesville , MD January 06, 2018 Hot water wouldnot shut off I called on your service, a person on the phone name Mr.Berry ask what the matter was . I told him the said a water valve should fix it . it sure was the right fix. thank you guys and thank you Mr. Berry. john m Read More... 2 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Nut Drivers, Pliers, Screwdrivers
Robert P Fort Wayne , IN April 29, 2014 Door spring link was broken Replaced link attached spring . Job done Read More... 2 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 30-60 minutes Tools: Nut Drivers, Pliers, Screwdrivers, Socket Set