Admiral Range Parts

Color: black. Small size. Measures about 2-1/2 inches in diameter.

This lid switch actuator engages the washer's safety switch when the lid is closed so cycles can start and spin as designed. Replace a broken or missing actuator to restore proper lid switch engagement and reliable operation.

• Engages the lid switch when the lid is closed to enable agitation and spin
• A worn, cracked, or missing actuator can cause the washer not to start or to stop before spin
• Intermittent operation that changes when pressing on the lid often indicates misalignment
• Lack of an audible "click" from the lid switch can point to a faulty actuator or alignment

• Disconnect power before servicing; do not work on a live appliance
• Access the lid/switch area per your model's service procedure
• Remove the damaged actuator and install the new part, securing as designed
• Before reassembly, close the lid to ensure the switch clicks and engages properly

This thermostat is a temperature-sensitive switch used in many ranges and wall ovens. It monitors heat and opens or closes the circuit at a set point to protect the appliance and help maintain proper operation.

• Senses temperature at its mounting location and changes state at a specified threshold
• Helps regulate oven heating or activate related cooling/vent components in the circuit
• Common symptoms of a faulty thermostat include no heat, overheating, shutting off mid-cycle, or a cooling/vent fan that won't run or runs constantly
• Electrical diagnosis varies by design; compare room-temperature continuity to your service information

• Disconnect power at the breaker and allow the appliance to cool completely
• Access location per your model; note wire positions and transfer one lead at a time
• Mount in the original location and orientation for accurate sensing; do not bypass the thermostat
• After reassembly, restore power and test operation

This power cord connects your appliance to household electricity, supplying safe, reliable power to its controls and components. Replace a damaged or overheated cord to restore dependable operation and reduce the risk of shorts.

• Supplies AC power from the wall outlet to the appliance's electrical system
• Helps resolve no power, intermittent power loss, or tripped breaker issues
• Replace if the cord is cut, frayed, melted, discolored, or feels hot at the plug
• Restores safe operation when the original plug or insulation is damaged

• Disconnect power at the outlet or circuit breaker before servicing
• Note wire routing and connection points; match the original orientation for hot, neutral, and ground
• Seat the cord properly and secure with the model's required strain relief or clamp to prevent tension on terminals
• Ensure the cord is not pinched and is clear of sharp edges, hot surfaces, and moving parts; test for proper operation

This blower wheel mounts on the drive motor and pushes air through the dryer drum and out the exhaust. Replacing a worn wheel restores proper airflow for consistent drying and helps prevent overheating and nuisance shutdowns. What it does:

• Moves air across the heater, through the drum, and out the vent to remove moisture
• Helps maintain proper airflow and temperature inside the dryer
• Common failure symptoms: reduced or no airflow at the exterior vent, longer dry times, unusual scraping/thumping or vibration from the blower area, or overheating/shutoff
• Cracked fins or a stripped hub can cause the wheel to slip on the motor shaft

• 1 blower wheel

• Disconnect power and turn off gas supply before servicing
• Access the blower housing per your model's service instructions; remove the retaining hardware and replace the wheel in the same orientation
• Clean lint from the blower housing and vent path; inspect the motor shaft and blower seal for wear
• Reassemble and verify the wheel spins freely without rubbing; check airflow at the exterior vent

This 8-inch surface burner element delivers heat on an electric cooktop or range. Replacing a worn or open element restores even heating on the burner zone and reliable response to temperature settings.

• Heats the 8-inch cooking zone when the surface control is turned on
• Helps maintain consistent pan temperature for boiling, simmering, and frying
• Common symptoms: burner won't heat, heats unevenly or intermittently, visible blistering/breaks in the coil, or scorch marks at the terminals
• Replacing a damaged element can prevent further damage to the receptacle/terminal block

• Disconnect power at the breaker and allow the unit to cool completely
• Handle the element by the bracket; avoid bending the coil
• For plug-in setups, pull the old element straight out and firmly seat the new one; for wired connections, move wires one at a time to the matching terminals and secure properly
• Inspect the receptacle/terminal block and wiring; replace if burnt or loose before restoring power

Razor blade scraper.

This 8-inch surface element kit restores reliable heat on your electric range or cooktop. Replace a failed burner so pots heat evenly and settings respond as expected across your 8-inch cooking zone.

• Heats the 8-inch surface burner for everyday boiling, simmering, and frying
• Replaces a burned-out or damaged element to restore consistent performance
• Helps eliminate weak, uneven, or intermittent heating
• Common symptoms: surface burner won't heat, heats inconsistently, or shows obvious damage

• Disconnect power at the breaker or unplug the appliance before servicing; allow all components to cool completely
• Note wire/terminal positions and transfer any mounting parts from the old element if required
• Ensure terminals are fully seated and the element is properly supported/seated before use
• After installation, test on low and high settings to confirm proper operation

Replace a damaged or discolored oven handle with this white door handle. It restores a secure, comfortable grip and a clean look so you can open and close your range or wall oven door with confidence.

• Provides the handhold used to open and close the oven door
• Replaces cracked, broken, loose, or missing handles
• Helps restore safe handling and original appearance
• White finish to match compatible models

• Disconnect power at the breaker and allow the oven to cool completely
• Support the door/outer glass; remove inner door screws to access the handle mounts
• Transfer any end caps or hardware from the old handle, if applicable
• Tighten fasteners evenly; reassemble and check door operation

Color: black. Measures about 2 inches in diameter.

Replace a worn or missing surface-burner knob with this black infinite switch control knob. It restores smooth, accurate heat selection on your range or cooktop when the original knob is cracked, stripped, loose, or missing. What it does:

• Interfaces with the surface burner's infinite switch to select OFF through Low–High heat levels
• Restores positive, secure control of the burner
• Typical symptoms: knob cracked, spins freely, falls off, or can't adjust temperature
• Helps ensure consistent response when turning the burner on/off and setting heat

• Disconnect power and allow the cooking surface to cool completely
• Pull the old knob straight off the switch shaft
• Align the new knob with the shaft and press on until fully seated; do not force
• Rotate through all settings to confirm smooth operation

By Maytag/Magic Chef. Set of 4 chrome square drip pans for gas ranges / cooktops. Fits many brands, including Maytag, Magic Chef, Admiral, Crosley, Norge, Jenn Air and others. Matching set of grates: 1430291.

The Range Clock Knob is an OEM part for Whirlpool ranges. It attaches to the center of the oven control panel and allows users to adjust the built-in clock, serving as the primary control for setting or correcting the time. 

Over time, the clock knob can become faulty due to regular use leading to internal stripping or wear, exposure to heat causing cracks or warping, or accidental impacts damaging the knob.

Color: Black

Symptoms of a defective range clock knob include:

• Difficulty setting or adjusting the clock
• The knob spins freely without engaging the control shaft
• The knob feels loose, cracked, or broken

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore ranges.

This thermostat knob fits onto the control shaft so you can select and adjust cooking temperature. Replace a cracked or stripped knob to restore smooth operation and a clean, finished look.

• Attaches to the thermostat stem to allow manual temperature selection
• Replaces knobs that are cracked, stripped, loose, or missing
• Helps when the knob spins without engaging or won't stay on the shaft
• Restores proper control feel and appearance

• Disconnect power to the appliance and allow surfaces to cool before service
• Pull the old knob straight off the thermostat shaft
• Align the new knob with the shaft and press straight on until fully seated; do not force
• The pointer aligns with the control markings before use

For the complete terminal block kit order 12001676.

This surface element supplies heat to an electric range or cooktop burner. When it fails, the burner may not heat or may heat inconsistently. Replacing the element restores steady, reliable cooking performance.

• Converts electrical energy into heat for the cooking zone
• Works with the surface control (infinite switch) to regulate temperature
• Common symptoms: burner won't heat, intermittent or uneven heating, visible breaks/blistering, burnt/melted terminals
• A failed element will not glow or reach set temperature when energized

• Disconnect power at the breaker before servicing and allow the cooktop to cool completely
• If your model uses a plug-in coil style: remove the drip pan, pull the element straight out of the receptacle, and inspect/replace a heat-damaged receptacle as needed
• If your model uses an under-glass radiant style: lift the cooktop, transfer any clips/limiters from the old element, and route wires exactly as original
• After reassembly, test the burner at a low setting to ensure proper operation