Amana Dryer Parts

Slid in new screen. Read more

I watched your video and had it fixed in less than 1 minute! Read more

• Takes too long to dry

My fiance was involved in a very nasty divorce where a very biased female judge forced him from his home for 14 months before he could take up residency again. He brought me back with him and I witnessed the grotesque damages she intentionally inflicted on his property. His washer and dryer are very expensive and high-end, as is the home and all his contents. One of the many damages she caused was that she had not cleaned the dryer lint filter in 14 months and the lint was a thick carpet which... Read more

• Will not tumble
• Takes too long to dry
• Noisy

I FOUND the website on t internet, found my part ordered it and watched the how to video ,repaired the dryer myself. Awesome Website. Read more

• Takes too long to dry
• No heat or not enough heat

Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered... Read more

I pulled the dryer away from the wall and unplugged it. Then I used a 5/16 nut driver and removed the 2 screws in the bottom front panel and pulled it off. Next I removed the 2 5/16 screws holding the front door panel and pulled it down far enough to disconnect the wires for the light and the wires on the door switch. Then , using a putty knife I popped the springs holding the top and control panel then pulling the top up and resting it against the wall. Now I started my repair by laying on... Read more

I ordered the new hinge and the cap they said would be needed, took the door apart and installed new hinge. Only problem, wish they told me I needed 4 of the caps, for one hinge and each cap was 11.95 x 4...pretty spendy. Fortunately I was able to reuse 3 of my worn ones for now. Read more

• Too hot
• No heat or not enough heat

The heating element had a break in the heater coils, so I replaced it with a new one from Appliance Parts Pros. I also replaced the thermal fusible link and thermostat switch because they were so cheap it just made sense to go ahead and do it while I was in there. I also cleaned every nook & cranny in the dryer, then cleaned out the vent piping- which was about 100% clogged. The video's of how to tear down a dryer were indispensable to this repair - along with APP's always having the right... Read more

I wanted to avoid pulling the drum. Luckily, my blower was easily accessed by pulling the front bottom panel. A couple of sheet metal screws were all I needed to remove the fan housing cover. I knew the fan was on reverse threads, i.e. righty-untighty. As it spins it tightens so no need for a retaining nut. I took off a screw holding on the exhaust tube and wiggled it out. I found the broken teeth inside. With the tube out of the way I was able to slide a crescent wrench in back and place... Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

• Marks left on clothes

Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered... Read more

I WENT ON-LINE & FOUND APPLIANCE STORE,THEY HAD MY PARTS, I ORDERED, THEY WERE SHIPPED IMMEDIATELY,WITHIN UNDER TWO DAYS.THIS WAS EXACTLY WHAT THEY SAID THEY WOULD DO.ALSO THE REPAIR VIDEO SHOWED ME HOW TO RUN THE BELT ON THE TENSIONER,I WAS AMAZED AT HOW SIMPLE & QUICK EVERYTHING WENT BACK TOGETHER.THANKS APPLIANCE STORE FOR BEING THEIR TO HELP ME GET MY GRANDSON"S DRYER BACK WORKING,I GIVE YOUR SITE A < A+ >. Read more

Originally the dryer was squeaking a lot, so I purchased a new belt tensioner, but the original tensioner was an old-style no wheel tensioner, so that wasn't the source of the squeaking. I saw a lot of lint had built up inside the unit where there shouldn't have been that much. So I viewed a few videos on the Appliance Pros site and saw that the rear wheel guides were the cause of the squeaking and the rear felt drum and blower housing seal needed to be replaced. The rear blower housing was... Read more

After reading the reviews of others, I ordered and replaced the heating element, thermostat, cut-off & the moisture sensor bars. It was a success! The element was definitely bad on one end, the wire was burnt in two pieces. Now it doesn't take 3 hours to dry a load! Well worth the money I spent. Easy to fix & do it yourself. I watched the video before buying the parts just to make sure that it was something I wanted to tackle. Very easy with the video. Great job Appliance Pro's! Read more

Watched You tube videos to narrow the problem down to old deteriorated gaskets. Read more

Use the videos on this website here and you can repair most brands. Many are duplicate in design. 1. Unplug the machine. 2. Move it away from a confined area to get more room. 3. Remove lint filter and the two screws that hold the exhaust filter port to the top of the cabinet. 4. Use a putty knife or actually a butter knife and release the top of the cabinet from the main drum housing. You will slide the knife between the top and the main cabinet at the plastic catches. Look for them and you... Read more