Amana Refrigerator Gasket & Seal

This refrigerator door gasket creates a tight seal between the door and cabinet to keep cold air in and moisture out. Replacing a worn or torn gasket restores consistent cooling performance and helps prevent frost and condensation from air leaks.

• Forms an airtight seal around the door perimeter to contain cold air
• Helps maintain proper temperatures and humidity inside the refrigerator
• Reduces frost, condensation, and warm spots caused by leaking seals
• Typical signs of failure: tears, gaps, hardened/warped corners, or doors not sealing firmly

• Unplug the appliance before servicing
• Let the new gasket warm to room temperature; use warm water or a hair dryer on low to relax bends
• Press the gasket fully into the door channel and seat the corners evenly
• Close the door and check for uniform contact all around; allow time for the gasket to conform

This refrigerator door gasket seals the fresh food door to keep cold air in and moisture out. Replace a worn seal to restore temperature control, reduce condensation, and help the appliance run efficiently.

• Creates an airtight seal between the door and cabinet
• Helps maintain stable interior temperatures and reduce energy loss
• Limits moisture buildup around the door opening
• Replaces gaskets that are cracked, torn, shrunken, deformed, or not sealing

• Disconnect power before servicing
• Allow the new gasket to relax; if needed, warm it in hot water to ease installation
• Remove the old gasket carefully; seat the new gasket fully into the door channel, checking corners
• Verify door alignment and test the seal by closing on a sheet of paper and adjusting as needed

This freezer door gasket forms the airtight seal between the door and cabinet. Replacing a worn gasket restores a proper seal, helping maintain temperature and reducing frost and moisture for more reliable freezer performance.

• Creates the perimeter seal to keep cold air in and humid air out
• Helps prevent frost/ice buildup and temperature swings inside the freezer
• Supports smooth door closing and even contact around the frame
• Common symptoms: tears, cracks, warping, gaps, persistent frost, or warm spots

• Unplug the appliance before servicing
• Warm/relax the new gasket in hot water or with a hair dryer on low to improve fit
• Start at a corner and press the gasket lip fully into the retainer channel; ensure corners seat first
• Check the seal with a paper test and gently reshape as needed; allow time for the gasket to conform

Freezer Door Gasket

This freezer door gasket replaces a worn or deformed seal to restore a tight, even closure on the freezer door. A proper seal keeps cold air in and humid air out, reducing frost buildup and temperature swings.

• Creates an air-tight seal between the freezer door and cabinet to contain cold air
• Helps maintain correct temperature and efficiency; reduces frost/ice around the door perimeter
• Symptoms of failure: tears, cracks, warping, gaps, or door not closing fully
• Presents as frost buildup, moisture/condensation, or warm spots in the freezer

• Disconnect power to the refrigerator before servicing
• Let the new gasket relax (lay flat; warm gently with hot water or a hair dryer) for easier fit
• Remove the old gasket from the retainer/channel; on screw-retained styles, loosen (do not remove) liner screws as needed
• Seat the new gasket evenly, starting at the corners; use gentle heat to smooth wrinkles and ensure a uniform seal all around

This is the front seal for the refrigerator's crisper compartment. It restores a tight barrier at the drawer's front edge so the crisper closes flush and maintains proper humidity to help keep produce fresh.

• Seals the front edge of the crisper to limit air leaks between the drawer and fresh food compartment
• Helps maintain intended humidity levels inside the crisper
• Restores smooth, flush closure of the drawer front
• Replace if the seal is torn, deformed, or missing; symptoms can include excess condensation or wilting produce

• Unplug the refrigerator and remove the crisper drawer
• Pull the worn seal off the crisper front/channel and clean the mating surface
• Warm the new seal in hot water to improve flexibility; press it evenly into place and ensure corners are fully seated
• Reinstall the drawer and verify proper alignment and closure

This gasket seals the FIP assembly to prevent air and moisture leaks, helping maintain proper temperature and efficiency. A worn or damaged seal can lead to condensation, frost buildup, or temperature fluctuations.

• Creates an airtight seal at the FIP interface to keep air and moisture out
• Helps reduce frost/ice accumulation and condensation around the assembly
• Can address issues like warm spots, frequent cycling, or visible gaps at the seal
• Restores proper sealing performance when the original gasket is cracked, flattened, or torn

• Disconnect power before servicing; wear cut-resistant gloves
• Remove cover/fasteners to access the FIP sealing surface
• Clean mating surfaces; install gasket evenly without stretching
• Verify even seating and recheck for pinches or gaps before reassembly

This freezer door gasket seals the door to the cabinet to keep cold air in and humid air out. Replacing a worn gasket restores a proper seal, helping maintain temperature and reducing frost and condensation around the door.

• Creates a continuous perimeter seal between the freezer door and cabinet
• Helps stabilize freezer temperatures and limits warm-air leaks that can lead to frost/ice buildup
• Common failure signs: torn or hardened gasket, visible gaps, moisture or ice near the door
• Almond color to match compatible units

• Disconnect power to the refrigerator before servicing
• Warm the new gasket in hot water or with low heat to relax folds, then start at the corners and work evenly around the door
• On screw-retained styles, loosen perimeter screws and tuck the gasket lip under the retainer; tighten evenly
• After installation, check seal with a dollar-bill test and allow up to 24 hours for the gasket to fully conform

This heat-resistant fiberglass oven door gasket seals the oven cavity perimeter, helping keep heat inside for consistent temperatures and efficient cooking. Replace a worn, frayed, or flattened seal to restore proper door sealing performance. What it does

• Forms a heat-resistant seal around the oven opening to minimize heat loss
• Helps maintain set temperature and overall cooking performance
• Can help address long preheat times, uneven baking, and hot air leaking around the door
• Replace if the gasket is frayed, brittle, compressed, or falling out of its channel

• Includes: 1 fiberglass door gasket

• Disconnect power and allow the oven to cool completely before service
• Remove the old gasket from its mounting slots or clips; clean the channel of debris
• Install the new gasket without stretching; seat it evenly around the perimeter with ends routed as originally positioned
• Close the door and check for uniform contact all around; adjust seating if needed

This fresh food door gasket seals the refrigerator compartment door to keep cold air in and warm air out. Replacing a worn gasket restores a tight seal, improves temperature stability, and helps prevent condensation and frost around the door.

• Seals the perimeter of the fresh food (refrigerator) door to limit air leaks
• Helps maintain proper interior temperature and efficiency
• Typical symptoms of failure: door not closing or sealing fully; visible tears, gaps, or warping
• May cause moisture, sweating, or frost near the door gasket area

• Disconnect power before servicing
• Warm and relax the new gasket (soak in warm water or use low heat) to ease installation; do not overheat
• Clean the door's gasket channel; install starting at the corners and ensure even seating all around
• Close the door and check for uniform contact; use a paper-slip test to confirm the seal

This genuine-style freezer door gasket creates a tight seal between the freezer door and cabinet to help maintain cold temperatures and reduce frost buildup. Replacing a worn gasket restores a proper seal and improves cooling efficiency. What it does:

• Seals the freezer door to keep cold air in and warm air out
• Helps prevent frost and ice buildup inside the freezer
• Reduces compressor run time caused by air leaks
• Can stop visible gaps or drafts around the freezer door edge

• Disconnect power and remove food before replacing the gasket; allow the freezer to reach room temperature if iced over
• Clean and dry the door sealing surface thoroughly before installing the new gasket
• Warm or flex the gasket slightly to seat it evenly in the channel; avoid overstretching
• Inspect the door retainer and ensure the gasket sits fully in the channel; use only appropriate, non-sharp tools to avoid damage

The Door Gasket is an OEM part for Whirlpool refrigerators. This gasket provides a seal between the freezer door and the main cabinet, ensuring a tight closure and preventing cold air from escaping. It is made of high-quality materials that provide a reliable barrier against temperature fluctuations and help maintain cooling efficiency.

A bad freezer door gasket can occur due to wear and tear, damage, or improper installation. If you notice symptoms such as frost buildup inside the freezer, decreased cooling performance, or a loose-fitting freezer door, it may be time to replace the  the worn-out or damaged freezer door gasket with this genuine OEM part.

Symptoms of a bad freezer door gasket include:

• Frost buildup inside the freezer
• Decreased cooling performance
• A loose-fitting freezer door

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This replacement door gasket creates an airtight seal around the refrigerator door to help keep cold air in and reduce frost buildup. It restores proper sealing to improve cooling consistency and energy efficiency. What it does:

• Seals the door edge to prevent cold air loss and reduce moisture/frost inside the cabinet
• Helps the compressor run less frequently by maintaining a stable internal temperature
• Commonly used when the existing gasket is torn, stretched, flattened, or no longer seals evenly
• Reduces warm spots and food spoilage that can result from a failing door seal

• Clean the door surface and gasket mounting channel before installing to ensure a tight seal
• Align the gasket evenly around the door and press into the channel; warm the gasket with a hair dryer if needed to ease installation (low heat only)
• Check door closing and seal after installation; avoid using sharp tools that can damage the gasket

The Door Gasket is an OEM part for Whirlpool refrigerators. It forms an insulating perimeter around the refrigerator door opening to maintain cool interior temperatures during use.

Causes relate to the breakdown of sealing materials from repeated compression cycles over many years. Cracks or loose areas compromise the barrier.

Symptoms of a defective door gasket can include:

• Warm air entering around the door edges
• Interior humidity increases causing frost or condensation
• Higher electric bills from lost cooling efficiency
• Inability to maintain set temperatures over long periods

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: Color - Grey

This is the rear crisper seal that fits along the back edge of the refrigerator crisper compartment to help maintain the crisper enclosure and reduce air leakage. It restores a tighter seal for better humidity control and food storage. What it does:

• Replaces a worn or torn rear crisper gasket to help reduce cold air loss from the crisper area
• Helps maintain crisper humidity so produce stays fresher longer
• Prevents gaps that can cause uneven cooling or frost build-up near the drawer
• Can reduce draft noise or rubbing caused by a damaged seal

• One rear crisper seal (matches OEM part number)

• Remove the crisper drawer to access the rear seal before replacing
• Peel out the old seal and press the new seal firmly into the gasket channel; ensure an even, continuous fit
• Avoid using sharp tools that could damage the cabinet or new seal
• Unplug the refrigerator or switch off power if needed for safe access to nearby components