Amana Washer Bearing Parts

The Thrust Bearing Kit is an OEM part for Whirlpool washing machines. This kit is essential for the proper operation of the washer's transmission system, allowing the drive system to engage smoothly and efficiently. 

Over time, components within the thrust bearing kit can wear down or become damaged due to the constant stress and movement they endure during the wash cycle. This wear can lead to issues with the washing machine's ability to agitate or spin correctly.

Symptoms of a bad Thrust Bearing Kit include:

• The washing machine is noisy during operation
• The washer struggles to agitate or spin
• The washing machine may fail to spin at all, leaving clothes wet at the end of the cycle
• Excessive vibration during use

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Bearing and Seal Kit is an OEM component for Whirlpool and KitchenAid front-load washing machines. The kit includes 2 center post bearings, 3 agitator shaft seals, and 1 center post seal.

These internal seals help retain lubrication inside the motor shaft housing, while the bearings allow for smooth rotation of critical components like the drive pulley. Continuous belt rubbing and water exposure diminish their lifespan over time.

Symptoms of worn motor seals or bearings include:

• Abnormal vibrations during the wash or spin cycles
• Noisy operation and grinding sounds from the motor
• Difficulty starting or stopping the cycle

This OEM kit is also compatible with Maytag, Jenn-Air, Magic Chef, and select Kenmore models.

The Spin Tube Bearing is an OEM replacement part for Whirlpool washing machines. It is a stationary bearing located inside the tub that supports the agitator and spin basket during operation. The bearing works to reduce friction and facilitate smooth spinning motion.

Symptoms of a bad spin tube bearing include:

• Excessive vibration or noise during the spin cycle
• The agitator or basket wobbling noticeably
• Difficulty Balancing loads
• Premature wear of other components

Causes of a bad bearing can include wear and tear due to repeated use over time, damage from cleaning products or foreign objects inside the tub, or improper handling during repairs.

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This thrust ring is a small spacer that controls end-play on a shaft or gear, keeping parts aligned and reducing friction. Replacing a worn ring restores smoother, quieter operation and helps prevent premature wear in the assembly.

• Maintains axial spacing and limits end-play in rotating assemblies
• Reduces friction and metal-to-metal contact between components
• Helps stabilize shafts/gears to minimize noise and vibration
• Replace if you notice scraping/grinding sounds, wobble, or visible wear on the old ring

• Disconnect power before servicing
• Refer to your model's parts diagram to confirm orientation and stack order with any spacers/washers
• Clean the shaft and mating surfaces; replace any companion parts that show severe wear
• After reassembly, check for smooth rotation and proper end-play before returning to service

This replacement main bearing assembly supports the washer's drive/spin system. It keeps the inner basket and drive shaft rotating smoothly and quietly, helping maintain alignment and reducing vibration during wash and high-speed spin.

• Supports and centers the spin basket/drive shaft for low-friction rotation
• Helps reduce noise and vibration when spinning at high RPMs
• Restores smooth operation when the original bearing is worn or rough
• Common symptoms: roaring/grinding during spin, basket wobble/play, roughness turning by hand, possible leak at rear center if related seal wear is present

• Disconnect power and water before service; allow the appliance to cool
• Access and replacement procedures vary by model; significant disassembly is typical
• A bearing press/driver may be required; inspect shaft and related seals and replace if worn
• After reassembly, run a test spin to check for leaks

This centerpost bearing supports the washer's spin basket on the stationary center post, providing a low-friction surface for smooth, quiet rotation. Replacing a worn bearing helps restore proper spin performance and reduce noise and vibration.

• Supports and centers the spin basket on the tub centerpost/drive shaft
• Provides a low-friction bearing surface to reduce wear and noise
• Helps maintain basket alignment and stability during spin
• When worn, may cause grinding or squealing in spin, excessive vibration or wobble, and poor/slow spin

• Disconnect power and water supply before servicing; use proper PPE
• Access typically requires removing the agitator, inner basket, and related drive components
• Clean mating surfaces; inspect the centerpost/spin tube and tub seal and replace any worn seals per service guidance
• Seat the bearing fully and verify smooth basket rotation before reassembly

Can be upper or lower bearing depending on application.