Amana Washer Gasket & Seal

I noticed the rubber seal (bellow) was damaged near the bottom of the bellow. It looks like removing clothes from the machine had worn away and eventually ripped away some of the seal. This caused water to leak out the bottom of the door. I looked up the model number of my washer on the web and searched for the part number of the bellow. Once I found it I searched eBay, Amazon and a few other places for the part number and opted for Appliance Parts Pros. The part was reasonably priced and... Read more

• Leaking

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more

• Marks left on clothes

Remove Top of washer Remove Top bracket that covers soap dispenser Disconnect plug that leads to the front control panel Remove 3 screws from underneath the bottom kickplate, remove kickplate Remove 2 screws holding Door, remove door Remove screws holding the front of the machine Using long Phillips screwdriver, loosen the screw that connects the metal wire band that encircles the rubber baffle on the Tub side, remove band Using needle nose pliers, remove the door side baffle ring by pulling... Read more

I replaced the washer plate and new screw/washer part. Easy fix and back up and running in ubder 10 minutes. Read more

Replaced the bellow. Read more

• Leaking

In reality, this turned into a full-on rebuild project - with several parts orders, not just a simple repair. But I have to give credit: The parts listings with pictures on the AppliancePartsPros web site were really useful in figuring out what was going on inside the machine, and what parts I would need. Also: The repair videos were critical for me to be able to ensure I was reassembling everything correctly. Shout out to Simon, who was featured in several of the repair videos. His "gorgeous... Read more

Just like the one's I have worked on for 30 years for Whirlpool. Read more

• Will not agitate
• Pumps but will not spin

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more

As a Mechanic, I did the common sense approach: INITIAL OBSERVATIONS & CHECKS: - Unplug Machine & check inlet water hose connections for leaks and signs of hose failure; - Remove back panel & inspect for water presence at all hose connections, pump, bottom of basket (bottom center of basket where the main motor, shaft bearing, and tub seal is located), dispensers, bottom of wash basket, water injector area, look everywhere where there is a hose connection and where water flows... - Inspect... Read more

This repair was performed on a Whirlpool Cabrio clothes washer Model # WTW5640XW0 which has the digital electronic controls rather than the older style timer, electro/mechanical controls. This washer was made in 2010. Simply having the diagnostic programs on this machine is wonderful and they work remarkably well and led me to the shifter/rpm sensor component straight away. It was a simple replacement by tipping the washer onto its front and accessing through the bottom. The machine was put... Read more

Disassembled and confirmed the clutch was bad. Also noticed a slight leak from the transmission shaft seal. Ordered replacement clutch, seal and oil from appliancepartspros.com. The parts arrived very quickly and exactly as ordered. Their repair videos were very accurate and made the job easy. I accomplished a quality repair at a reasonable cost. My thanks to the folks at appliancepartspros.com for making it possible! Read more

Replaced clutch assembly, gearcase input shaft seal and motor coupler. When I disassembled the washer I realized the shaft seal on the top of the gearcase was leaking and not the input shaft seal. So had to order more parts before I could finish this job. Altogether I replaced agitator dogs, both seals on the gearcase, the clutch assembly and the motor coupler. Agitator dogs replacement is a very easy job, no tools required, takes less that 5 minutes and made a huge difference with how well... Read more

First off I have to say that Appliance Parts Pro's saved me from hiring a repair person, and quite possibly just getting rid of my washing machine. Their video's helped out SOOOOOOOO much and the advice one of their agents gave me over their online chat helped me trouble shoot something when I got stuck. On top of this they shipped my parts fast enough that less than 12 hrs later they arrived, which allowed me to get my machine up and running way faster than the other options I had available.... Read more

Used the parts and youtube video from your company. Read more

With the basket out of the dishwasher, the plastic parts basically snap on and off... popped the broken parts off and the new parts on. The 2 wheel and mount assemblies were a little more complicated. The video on the website advises to disconnect the supply line and drain line... I didn't have to do this. I just pulled the dishwasher out of its cabinet a little over a foot and removed the 2 screws holding each assembly in place and removed them. The previous gaskets (2 PER ASSEMBLY)... Read more

Read articles and watched How-To video on AppliancePartsPros.com. Videos were very informational and parts arrived very quickly! Read more