Amana Washer Parts

This fill hose carries water from the home supply to the appliance inlet valve, restoring proper water fill and helping prevent leaks when the original hose is cracked, worn, or blocked. Ideal for replacing damaged inlet lines. What it does:

• Delivers water from the household supply to the appliance inlet valve for normal fill cycles.
• Replaces cracked, split, or deteriorated hoses that can cause leaks at connections.
• Resolves symptoms such as slow or no water fill, visible leaks, or intermittent filling.
• Durable replacement designed to match OEM routing and connection points.

• Always shut off water supply and disconnect power before starting work.
• Inspect and replace hose clamps or inlet gaskets as needed; ensure proper seating to prevent leaks.
• Hand-tighten fittings and secure clamps—avoid overtightening metal fittings.
• After installation, restore water and power and run a short fill cycle while checking for leaks.

This stacking kit secures a dryer on top of a compatible washer to save floor space and stabilize the stacked units. It helps keep the dryer aligned and reduces shifting or rocking during use. What it does:

• Provides a secure connection between dryer and washer to create a stable stacked laundry configuration.
• Helps prevent the dryer from sliding, tilting, or shifting during spin cycles — common signs a stack kit is needed.
• Uses brackets and mounting hardware to fasten the dryer to the washer and maintain alignment.

• Disconnect power to both appliances and follow all safety precautions before starting installation.
• Have a second person assist when lifting or positioning the dryer to avoid injury or damage.
• Follow the OEM installation instructions and torque guidance for mounting hardware; ensure both appliances are level and stable after installation.

The Drum Baffle is an OEM part for Whirlpool washing machines. It is an internal component located inside the tub or drum that helps distribute water flow efficiently during the wash cycle. The baffle directs water in a way that ensures items are soaked and soaked evenly on all sides for thorough and effective cleaning.

Symptoms of a bad baffle include:

• Poor washing or rinsing performance 
• Items not getting completely clean or taking longer to wash
• An off-balance wash load  
• Excessive noise or vibration during spin cycles

Causes of a bad drum baffle can be normal wear and tear over time, or damage due to an off-balance or overfilling of the wash load. This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. Replace yours today to optimize washing quality.
 

Includes suspension pads.

This mechanical cycle timer controls the sequence and duration of washer operations. Replacing a failing timer restores proper advancement through fill, agitate, drain, and spin so cycles complete reliably with accurate timing. What it does:

• Advances the washer through each step by routing power to the water valves, motor, and drain pump at the correct times
• Sets the length of each stage for consistent operation
• Common failure signs: cycle won't advance or stops mid-cycle
• Timer knob doesn't move or must be jiggled to run
• Skips functions (no agitate, drain, or spin) while others still work

• 1 mechanical timer assembly

• Disconnect power before servicing; access the timer from the control console
• Take photos or label wires; transfer them to the new timer one at a time to maintain correct positions
• Reuse the existing knob and dial; align the timer shaft properly and secure the mounting screws
• After reassembly, run a short test cycle to ensure proper advancement

This knob assembly replaces the "modifier" control knob on the console so you can adjust settings smoothly and reliably again. Restore a secure, positive-turn feel when the original knob is cracked, stripped, or missing.

• Attaches to the control shaft to select and adjust options/settings
• Replaces knobs that are cracked, broken, or missing
• Fixes a knob that spins freely, slips, or won't turn the control
• Restores proper selection and tactile feedback during use

• Disconnect power to the appliance before servicing
• Pull the old knob straight off the shaft; avoid prying against the panel
• Align the flat/splines on the new knob with the shaft and press on firmly until fully seated
• The pointer aligns with the panel markings before use

This 1/4 HP motor assembly replaces a worn drive motor to restore proper drive power and rotation. It's a direct-fit mechanical motor intended to bring moving components back to OEM performance and reliable operation. What it does

• Provides drive power for the appliance's rotating components to restore normal operation.
• Replaces a failed or noisy motor that causes little or no rotation, intermittent operation, or a humming/stalling condition.
• Helps eliminate abnormal motor noise, vibration, or overheating when the motor is the root cause.
• Restores consistent mechanical speed and torque for components that rely on the motor to function.

• One 1/4 HP motor assembly

• Disconnect power before servicing; follow all safety precautions.
• Verify mounting orientation, shaft alignment, and proper belt/drive configuration during reassembly.
• Inspect and replace worn belts, pulleys, or mounting hardware as needed to prevent repeat failures.

This silicone lubricant is used during appliance service to condition rubber seals and O-rings, especially in dishwashers. It eases installation and helps new seals seat properly for a reliable, leak-resistant connection on pumps, valves, and hose fittings.

• Lubricates rubber seals, O-rings, and gaskets to prevent rolling, tearing, or binding during assembly
• Helps seals seat correctly to support leak-resistant joints
• Aids insertion of hoses, plastic fittings, and pump components
• Helpful when reassembling sump, diverter, inlet, and drain connections
• Common signs it may be needed: difficulty installing seals, seals that dislodge, or seepage after a seal replacement

• Disconnect power and water before servicing the appliance
• Clean and inspect mating surfaces; replace any cracked, flattened, or cut seals
• Apply a light, even film to the rubber part only; avoid over-application
• Wipe away excess; do not use lubricant to compensate for damaged seals—replace them

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

This 3-position temperature switch selects the dryer's heat level so the appliance reaches the desired drying temperature. It replaces a worn or faulty selector to restore proper temperature selection and consistent drying performance. What it does:

• Switches between three temperature settings to control dryer heat levels.
• Routes power to the heater circuit based on the selected heat setting.
• Commonly replaces a switch that causes incorrect heat, no heat on some settings, or inability to change temperature.
• Works with the dryer's control system and thermostats to maintain selected drying temperature.

• Disconnect power to the appliance before attempting any service.
• Handle terminals and connectors carefully; match wiring to original locations or take a photo before removal.
• Verify operation with a multimeter for continuity per service manual before and after installation.

This gearcase is the washer transmission that transfers motor torque to the agitator and wash basket, restoring agitation and spin function in compatible top-load washers. Durable replacement for worn or noisy transmissions. What it does

• Converts motor rotation into the geared motion needed for agitation and spin.
• Stops gear slippage and restores proper agitation when the original unit is worn.
• Can reduce grinding, clunking, or loss-of-drive symptoms related to a failed transmission.
• Supports normal wash and spin cycles when installed correctly.

• One gearcase (transmission) assembly.

• Disconnect power and water before starting any repair.
• Requires basic hand tools and access to the washer cabinet; some models need the agitator, basket, and motor removed.
• Inspect associated seals, fasteners, and linkage for wear and replace as needed; use factory service instructions for torque and alignment.

Size: 26 inches long. F18t8/cw/k26.

This outer trim panel cover replaces a cracked, broken or missing exterior cover to protect internal components and restore the appliance's finished appearance. It fits where the factory cover shields wiring and mounting points. What it does:

• Protects wiring, switches and internal parts from debris and accidental contact
• Restores the appliance's exterior finish and prevents drafts or gaps
• Stops rattling or vibration caused by damaged or loose trim
• Helps keep moisture and dust out of sensitive areas

• Disconnect power to the appliance before starting any repair.
• Remove any adjacent panels or fasteners to access the cover; retain screws and clips for reassembly.
• Align cover tabs and secure with original screws or clips; do not force or overtighten to avoid cracking.
• Replace those parts before finishing the repair.

This standpipe adapter connects the appliance drain hose to the household standpipe or waste outlet, helping ensure a secure drain path and reduce the risk of leaks or poor drainage. Simple replacement for damaged or worn connectors. What it does:

• Provides a sealed connection between the appliance drain hose and the standpipe or drain outlet
• Prevents water leaks at the hose-to-standpipe junction
• Helps maintain proper drainage and reduces gurgling or slow-draining symptoms
• Durable plastic construction designed to resist cracking and wear under normal use

• One standpipe adapter

• Turn off and unplug the appliance and stop water flow before replacing the adapter
• Remove the old adapter and clean the mating surfaces; ensure the hose and standpipe are free of debris
• Slide the drain hose onto the adapter fully and secure with the proper clamp or retainer
• If you find cracks in nearby hoses or fittings, replace those parts as needed and test for leaks after installation

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:

• Provides adjustable height to level an appliance on uneven floors.
• Eliminates rocking or wobbling that can cause vibration, noise or movement during operation.
• Helps ensure doors and panels sit flush and seal properly.
• Durable replacement designed for direct fit where the OEM leveling foot is specified.

• Disconnect power and water before performing any work.
• Support the appliance so it cannot tip—use a jack or have a helper hold it while you adjust feet.
• Turn the foot to raise or lower the corner; use hand tools as needed and avoid excessive force.
• After adjusting, check stability and run a short cycle to ensure vibration and alignment are resolved.