Amana Washer Parts

Fix unresponsive or erratic cycle selection with this rotary encoder switch. Mounts behind the control knob to restore accurate cycle settings and indicators.

This 3-position temperature switch selects the dryer's heat level so the appliance reaches the desired drying temperature. It replaces a worn or faulty selector to restore proper temperature selection and consistent drying performance. What it does:

• Switches between three temperature settings to control dryer heat levels.
• Routes power to the heater circuit based on the selected heat setting.
• Commonly replaces a switch that causes incorrect heat, no heat on some settings, or inability to change temperature.
• Works with the dryer's control system and thermostats to maintain selected drying temperature.

• Disconnect power to the appliance before attempting any service.
• Handle terminals and connectors carefully; match wiring to original locations or take a photo before removal.
• Verify operation with a multimeter for continuity per service manual before and after installation.

Adjustable leveler leg that stabilizes and levels compatible Whirlpool appliances. Replacing a worn or damaged leveler restores proper balance, reduces rocking, and helps doors and drawers align and seal correctly. What it does

• Raises or lowers the appliance to achieve a level position on uneven floors.
• Stops rocking or wobbling that can cause noise or uneven wear.
• Helps doors and drawers close and seal properly by correcting tilt.
• Replace when threads are stripped, the foot is broken, or the leg no longer holds height.

• Disconnect power (and water supply for appliances with hookups) before working beneath or behind the unit.
• Support the appliance securely (use blocks or have a helper) before removing or adjusting levelers.
• Most levelers screw in/out—turn to raise or lower, then test stability and door alignment.

Includes suspension pads.

Silicone lubricant conditions rubber seals and O-rings in appliances. Apply during service to ease installation and prevent leaks. Confirm fit by model.

This mechanical cycle timer controls the sequence and duration of washer operations. Replacing a failing timer restores proper advancement through fill, agitate, drain, and spin so cycles complete reliably with accurate timing. What it does:

• Advances the washer through each step by routing power to the water valves, motor, and drain pump at the correct times
• Sets the length of each stage for consistent operation
• Common failure signs: cycle won't advance or stops mid-cycle
• Timer knob doesn't move or must be jiggled to run
• Skips functions (no agitate, drain, or spin) while others still work

• 1 mechanical timer assembly

• Disconnect power before servicing; access the timer from the control console
• Take photos or label wires; transfer them to the new timer one at a time to maintain correct positions
• Reuse the existing knob and dial; align the timer shaft properly and secure the mounting screws
• After reassembly, run a short test cycle to ensure proper advancement

This 250V, 1A fuse protects your washer's control circuit from overcurrent. Replacing it can restore control power once the root cause is corrected.

• Opens to protect electronics when current exceeds its 1A rating
• Check this part if the washer has no power, the control panel is dead, or it won't start
• A blown fuse will test open for continuity
• Repeated failure points to an underlying short or component fault that must be fixed

• Disconnect power before servicing
• Access the fuse at the control board or fuse holder
• Replace only with the same rating: 1A, 250V
• Inspect wiring/components and correct any short before restoring power

Color: Black. Instruction sheet included.

Washer making noise or experiencing weak water circulation? This impeller cap secures the wash pump impeller for proper water flow and performance.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

Almond. Size: 13 oz. can. Acrylic appliance paint.

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Replacement flexible hose that routes water inside your washer. Needed when original is cracked, kinked, worn, or leaking. Restores secure flow.

White porcelain touch-up paint for repairing chipped, scratched, or worn surfaces on ranges, ovens, and refrigerators. Restores appearance on exterior panels and trim. 2 oz. can.

Touch-up paint for appliances in almond color. Repairs chips, scratches, and worn spots on ovens, refrigerators, microwaves, and dryers.

Adjustable leveling leg with foot pad for dryers, washers, and pedestals. Replace cracked, broken, or missing legs to stabilize your appliance.