Parts for Ge DPSE810GG2WT: 01 - Backsplash, Blower & Motor Parts

White left-hand end cap for dryers. Covers and protects the side panel edge. Replace if cracked, broken, or missing to restore appearance.

White right-hand console endcap for dryers. Replaces cracked, broken, or missing endcaps on the control panel edge. Restores appearance and protects.

White control knob assembly for washer control panels. Replaces broken, cracked, or missing knobs that won't turn properly or have damaged collars.

Fix a dryer that won't start, has a dead console, or runs erratic cycles by replacing the electronic control board. DIY-friendly repair.

Fix power connection issues in your dishwasher with this terminal block. Resolves electrical failures and burnt connections. Standard difficulty repair.

Replacement screw for securing dryer components like drum supports, panels, and housings. Needed when screws are lost, stripped, or damaged during repair.

Secures the ground wire to the dryer cabinet for safe electrical connection. Replace if missing, stripped, or corroded to restore proper grounding.

Dryer barely blowing air or taking forever to dry? A worn blower wheel fails to pull air through the drum. This wheel restores airflow for efficient drying.

A small rubber-lined washer that cushions and electrically isolates connections to reduce metal-on-metal contact and damp vibration. Helps protect parts and maintain proper spacing for reliable operation. What it does:

• Cushions fasteners and mounting points to reduce vibration and noise
• Provides electrical insulation between metal components
• Prevents wear from direct metal-to-metal contact
• Keeps assemblies aligned by maintaining correct spacing

• Disconnect power to the appliance before servicing
• Access the mounting area per your model's service instructions
• Replace with the same style and orientation to ensure proper fit and insulation
• Inspect surrounding hardware and replace any damaged fasteners or worn mounting surfaces

Secures the drive motor to its mounting bracket. Replace if cracked, broken, or missing to keep the motor and blower aligned and stable during operation.

Secures your dryer motor to the cabinet to reduce vibration and noise. Replace if motor shifts or rattles during operation. Confirm fit with your model.

Metal bracket that secures the dryer motor and blower assembly in place. Replace if your mounting bracket is cracked, broken, or causing loose components.

Transfers power from motor to drum in your dryer. Replace if squeaking, not spinning, or visibly worn. Confirm fit with your model number before ordering.

Supports the idler pulley to maintain proper belt tension in your dryer. Replace if the arm is warped, cracked, or causing belt tracking issues.

Maintains tension on your dryer's drive belt. Replace if pulley is cracked, worn, or making noise. Installs inside drum assembly for smooth operation.

Seals the blower-to-exhaust duct connection in your dryer. Replace if torn, brittle, or causing heat loss and longer dry times. Confirm fit by model.

Replaces a cracked, rusted, or disconnected exhaust duct that routes hot air from your dryer to the home vent. Restores proper airflow and venting.

Fix a dryer that won't heat with this outlet backup thermostat. Mounts on exhaust duct for over-temperature protection. DIY repair in under 1 hour.

Hex washer-head screw secures dishwasher brackets, shields, and panels. Replace stripped, missing, or damaged screws to restore tight fit and stability.

Replacement mounting screw for dryer panels and components. Needed when original screws are stripped, missing, or damaged during repair or maintenance.

Dryer foam gasket seal that prevents air leaks and ensures proper drying efficiency. Replace when worn, compressed, or damaged to restore performance.

This motor plate is the stamped metal mounting plate that secures the motor assembly and keeps it aligned for smooth operation. It restores proper motor positioning and reduces vibration-caused noise or wear. What it does:

• Provides a stable mounting surface for the motor assembly
• Maintains motor alignment to ensure smooth shaft rotation
• Helps reduce excess vibration and noise from a loose or damaged motor support
• Supports related components so belts and pulleys track correctly

• Disconnect power before starting any repair to avoid shock or injury
• Installation requires basic hand tools and access to the motor compartment
• Verify motor and surrounding hardware are undamaged; replace any worn fasteners

Replacement mounting screw for dryer panels, brackets, and components. Needed when screws are missing, stripped, or damaged during repairs or disassembly.

Hex washer-head screw secures dishwasher brackets, shields, and panels. Replace stripped, missing, or damaged screws to restore tight fit and stability.

Factory replacement screw for securing dryer panels, brackets, and components. Restores lost or loose hardware to eliminate rattling and ensure proper fit.

Dryer not heating or sensor dry cycles erratic? The thermistor monitors temperature and signals the control board. Common fix, moderate DIY difficulty.

Replacement screw for dryer panels and brackets. Secures loose or rattling components. Restores stable fastening when original is missing or stripped.

Replacement screw secures dryer panels, brackets, and internal components. Replace stripped, lost, or damaged screws to eliminate rattles and maintain assembly.

Dryer won't start, stops mid-cycle, or runs backward? The drive motor powers drum rotation. Moderate difficulty repair requires disassembly. Video guide.

Dishwasher won't start or runs intermittently? A faulty door interlock switch prevents operation when the door latch fails. DIY repair in 20 minutes.

Replace your washer's control panel button if it's cracked, broken, or missing. This snap-in component installs on the control panel face plate.