Bosch Parts

The Panel Facia is an OEM part for Bosch dishwashers. It is the front control panel of your dishwasher, providing a clean and polished look.

A bad panel facia can occur due to wear and tear over time, accidental damage, or exposure to moisture and cleaning agents. Signs of a faulty facia include cracks, discoloration, or a loose fit that compromises the aesthetic appeal of your dishwasher.

Symptoms of a bad panel facia include:

• Cracks or visible damage on the surface
• Discoloration or fading
• A loose or missing panel

Replace your damaged or worn-out panel facia with this genuine OEM Bosch part to restore the appearance of your dishwasher. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

The Knob Set is an OEM part for Bosch cooktops. This set includes four burner knobs designed to control the heat settings of your cooktop burners. The knobs allow you to easily identify and adjust the desired heat level for each burner.

A bad burner knob can occur due to accidental damage, wear and tear over time, or improper handling. Signs of a faulty knob include cracks, loose or wobbly fit, or difficulty in turning the knob smoothly.

Symptoms of a bad knob include:

• Cracks or visible damage 
• Loose or wobbly fit 
• Difficulty in turning the knob 

Replace your worn-out or damaged knobs with this genuine OEM Bosch part to restore your cooktop. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

This driveshaft transmits motor torque to the appliance drum so the drum rotates smoothly. Replacing a worn or broken driveshaft helps stop excessive noise, wobble, scraping, or failure-to-spin symptoms. What it does:

• Transfers rotational force from the motor to the drum for normal operation
• Maintains drum alignment; a damaged shaft can cause wobbling or uneven rotation
• Failing shafts may cause loud squeaks, scraping noises, or prevent the drum from spinning
• Works with bearings, couplers and support assemblies—inspect related parts when replacing

• Disconnect power before starting work; follow all safety precautions
• Basic hand tools required; refer to the OEM diagram for disassembly steps
• Inspect and replace worn bearings, seals or couplers as needed to ensure proper operation
• If the shaft is seized or rusted, support the drum to prevent damage during removal

Size: 1 foot. This Bosch dishwasher drain hose comes with 2 o-rings. For the 5 foot drain hose order 00298564.

Color: stainless. It measures about 3-1/2 inches wide by 6 inches high.

Replacement spray arm that restores water distribution for better rinse coverage and more even cleaning. Installs in the dishwasher tub to re-establish spray patterns and water flow lost to cracks or wear. What it does:

• Rotates and directs high-pressure jets of water to rinse and loosen food soils from dishes and cookware
• Restores proper spray coverage when the original arm is cracked, clogged, warped, or not spinning freely
• Helps reduce spots and missed areas by re-establishing even water distribution across racks
• Works with the dishwasher's pump and tubing to maintain normal wash performance

• Disconnect power and turn off the water supply before beginning any service
• Remove lower rack and any retaining clip or cap to access the spray arm; note orientation for reassembly
• Inspect and clear spray holes of debris before installing; ensure the arm spins freely after installation
• Do not overtighten mounting hardware; replace any damaged clips or seals for a secure fit

This is the front control panel fascia for the appliance's user interface. It replaces a damaged or worn fascia so buttons and labels are protected and the unit looks and operates as intended.

• Houses and protects the control buttons/overlay area
• Restores proper alignment and visibility of controls
• Cosmetic renewal for scratched, dented, or cracked panels
• Common symptoms: loose or missing panel, cracked face, worn or unreadable markings

• Disconnect power before servicing
• Transfer any attached switches, display/overlay, and hardware from the old panel
• Handle stainless surfaces carefully to avoid scratches
• Verify correct seating of tabs and screws before reassembly

This replacement lid restores the appliance's finished top cover, protecting internal components and helping the door/hatch close properly. Use when the original lid is cracked, warped, or missing to keep the unit looking and operating as intended. What it does:

• Covers and protects the appliance's top/opening area from debris and damage.
• Secures to existing hinge or mounting points to ensure proper closure.
• Replace if you see visible cracks, chips, warping, or if the lid no longer latches or aligns.
• Helps prevent rattling or rubbing caused by a damaged or loose lid.

• Disconnect power (and water, if applicable) before starting any repair.
• Handle edges carefully; some lids include glass or thin sheet material that can chip.
• Basic hand tools (screwdriver/torx) may be required; keep mounting hardware if reusing.

Color: White. This is the right side trim strip. For left side use 00353048.

This water inlet hose gasket seals the connection between the supply hose and the appliance's inlet fitting. Replace a flattened or damaged washer to stop drips at the coupling and restore a reliable, watertight connection.

• Creates a watertight seal at the inlet hose-to-appliance connection
• Helps prevent drips, puddles, and water damage around the machine
• Replace if the old gasket is cracked, hardened, flattened, or missing
• Common symptoms: leaking at the hose coupling or needing to retighten the fitting to stop drips

• Disconnect power and turn off the water supply before servicing
• Place a towel to catch residual water, then detach the inlet hose from the appliance fitting
• Remove the old gasket from the hose coupling and seat the new gasket evenly
• Reattach and hand-tighten the coupling; open water supply and check for leaks—do not overtighten

This rear pump housing is the dishwasher's molded enclosure that supports the drain/pump assembly and channels wash and drain water. Replacing a damaged housing restores proper water flow and helps stop leaks. What it does:

• Houses and aligns the drain/pump components and motor coupling
• Channels water between sump, pump and drain lines to ensure proper draining
• Prevents leaks by sealing the pump assembly area when intact
• Can cause noisy pump operation or failure to drain if cracked or broken

• One rear pump housing

• Disconnect power and turn off water supply before starting; drain any standing water
• Inspect associated seals, gaskets, impeller and mounting hardware; replace if worn
• Handle carefully to avoid damaging mating surfaces; test for leaks after reassembly

The Panel Facia is an OEM part for Bosch dishwashers. It is the front control panel of your dishwasher, providing a clean and polished look.

A bad panel facia can occur due to wear and tear over time, accidental damage, or exposure to moisture and cleaning agents. Signs of a faulty facia include cracks, discoloration, or a loose fit that compromises the aesthetic appeal of your dishwasher.

Symptoms of a bad panel facia include:

• Cracks or visible damage on the surface
• Discoloration or fading
• A loose or missing panel

Replace your damaged or worn-out panel facia with this genuine OEM Bosch part to restore the appearance of your dishwasher. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

This trim strip mounting clip secures the decorative door trim on dishwashers with short side panels, restoring a flush, stable front appearance and preventing the trim from rattling or coming loose. Ideal when the trim has shifted or separated. What it does:

• Secures the outer trim strip to the dishwasher door at short-side-panel mounting points.
• Keeps trim aligned and prevents rattling, sagging, or visible gaps.
• Restores the finished look of the dishwasher front after trim movement or damage.
• Works with the original trim assembly and mounting hardware to maintain proper fit.

• Always disconnect power to the appliance before accessing the door assembly and follow OEM service instructions.
• Access typically requires removing the inner or outer door panel or lower access panel; preserve existing screws and hardware for reassembly.
• Clip installs into the designated trim mounting location; confirm orientation before fastening and avoid over-tightening.
• Obtain the correct fasteners from the OEM parts list.

This dual water inlet valve controls water flow to appliance components like the dispenser and ice maker, restoring proper water delivery when the valve is functioning. It replaces a faulty or leaking inlet valve to help stop water issues. What it does:

• Opens and closes water flow to the appliance's water circuits (dispenser/ice maker) when signaled
• Commonly linked to no water dispensed or ice maker not filling
• Can be a source of slow fill or intermittent water delivery
• A leaking or stuck valve can cause visible leaks or water pooling

• One dual water inlet valve

• Shut off water supply and disconnect power before servicing
• Use basic hand tools; avoid overtightening connections to prevent damage
• Inspect inlet hoses and seals when replacing the valve

Replacement oven door handle that restores a secure grip for opening and closing the oven door. Replaces cracked, broken or loose handles to help make daily use safer and more reliable. What it does:

• Provides a firm grip to open and close the oven door smoothly.
• Replaces handles that are cracked, broken, loose, or missing.
• Helps prevent further damage to door trim and reduces the risk of sudden handle failure.
• Designed for factory mounting locations for a straightforward swap.

• Disconnect power to the appliance before starting; for gas units, turn off the gas supply if applicable.
• Support the door while removing and installing the handle to prevent the door from dropping — use a helper if needed.
• Remove existing mounting screws or fasteners, position the replacement handle, then reinstall and snug hardware.