Parts for Kenmore 253.7041341A (2537041341A, 253 7041341A): Cabinet Parts

Replacement access panel cover for refrigerators. Shields internal components from dust and debris. Needed when original is cracked, broken, or missing.

Refrigerator making loud noises or not cooling? A worn evaporator fan blade often causes these issues. DIY-friendly repair typically takes 30 minutes.

Nylon washer for the evaporator fan motor shaft in refrigerators. Replace if worn, cracked, or missing to ensure proper fan alignment and operation.

Replaces worn or damaged shaft support bushing in your refrigerator. Cushions rotating shafts to reduce friction and noise. Order a new bushing today.

Seals the coil cover area to maintain proper airflow and prevent dust buildup. Replace if worn, cracked, or losing seal efficiency. Verify fit with your model.

The refrigerator ice maker hole plug is a rubber or plastic cap that seals the pre-drilled opening in the refrigerator cabinet wall that is used for ice maker water line connections. It keeps cold air from escaping through the unused hole in refrigerators that do not have an ice maker installed. Replace or install this plug if cold air is leaking through an open hole in the back wall of the refrigerator, causing temperature fluctuations or frost buildup.

This evap coil cover protects the evaporator and helps direct airflow for more consistent cooling. It replaces damaged or missing covers to reduce frost buildup, keep debris away from the coil, and help prevent interior leaks. What it does:

• Shields the evaporator coil from ice, debris and accidental contact to protect coil fins.
• Helps channel airflow across the coil for improved cooling performance.
• Can reduce frost accumulation and related moisture or dripping symptoms.
• When cracked or missing, you may notice increased frost, water in the cabinet, or reduced cooling.

• Always disconnect power to the appliance before servicing.
• Remove interior liners or access panels to reach the evaporator; handle coil fins and insulation carefully.
• Reinstall any mounting clips, grommets, or insulation exactly as removed to maintain fit and sealing.

Insulation for refrigerator air duct. Installs inside cabinet to maintain temperature efficiency. Replace if worn, torn, or missing insulation.

Fix SY EF error codes or warm refrigerator temperatures with this evaporator fan motor. Moderate DIY repair restores air circulation and cooling.

Interior light stays on or won't turn on when door opens? This door-activated switch restores automatic on/off lighting. Easy 15-minute fix.

Light lens cover for refrigerator interior lighting. Replaces cracked, yellowed, or missing lens covers. Snaps into place over bulb compartment.

Powers your refrigerator's interior lighting. Replace when lights dim, flicker, or fail. Confirm fit with your model number before ordering.

Refrigerator cover cap that installs on the exterior cabinet or internal components. Replace if cracked, broken, discolored, or missing to restore appearance.

Seals the air duct connection to prevent air leaks and maintain consistent temperatures. Replace when worn, cracked, or causing temperature issues.

This is a support bracket designed to hold the air damper assembly in place inside the refrigerator. The damper regulates airflow from the freezer into the fresh food compartment to maintain proper temperature. Replace this support if it is cracked or broken, which can cause the damper to sit improperly and lead to inconsistent temperatures in the refrigerator section.

Cover cap for bottom-mount refrigerators. Replaces cracked, broken, or missing covers. Installs on exterior or interior panels to restore appearance.

Replacement screw fastener for securing panels, trim, and components inside your refrigerator. Needed when original screws are stripped or missing.

Mounting screw for refrigerator components and panels. Replaces lost, stripped, or damaged screws. Essential hardware for secure assembly.

Replacement mounting screw for refrigerator panels, handles, brackets, and internal fixtures. Order when original screws are stripped, lost, or damaged.

This roller assembly consists of small caster-style wheels mounted on a support ring, designed to allow a shelf, drawer, or internal component to slide smoothly inside the refrigerator or freezer compartment. It supports the weight of stored items while enabling easy access. Replace this assembly if the rollers are cracked, seized, or if the shelf or drawer no longer glides properly and feels stuck or wobbly.

Secures internal components to the refrigerator frame. Replace this mounting bracket if the original is bent, broken, or missing to restore alignment.

Washer for bottom-mount refrigerators. Replaces lost, damaged, or worn washers used to secure components. Essential for proper assembly and fit.

Lower door hinge for bottom-mount refrigerators. Secures the door to the cabinet frame. Replace if cracked, stripped, or causing door misalignment.

Lower door hinge provides the pivot point for your refrigerator door. Replaces worn, damaged, or broken hinges that cause door sagging or misalignment.

Plastic spacer that mounts between refrigerator door components to maintain proper alignment and spacing. Replace if cracked, broken, or missing.

Door spacer for bottom-mount refrigerators. Maintains proper spacing between door panels and cabinet. Replace if cracked, missing, or worn to prevent rubbing.

Replacement corner trim that covers the cabinet edge of your refrigerator. Restores a finished look to cracked, chipped, or missing corner pieces.

Protects cabinet corners from chips and moisture damage. Replace when trim is cracked, missing, or no longer seals properly. Verify fit with your model.

OEM mounting bracket that secures the hinge and pin assembly inside your refrigerator. Replace if cracked, broken, or missing to restore proper alignment.

Supports and aligns the refrigerator door at the hinge pivot point. Replace if cracked, bent, or worn to restore stable door operation and proper sealing.

Plastic hinge cover that conceals the upper hinge assembly on your refrigerator door. Replace if cracked, broken, or missing for a clean finish.

Plastic cover that shields the upper door hinge on your refrigerator. Replace if cracked, broken, or missing to restore a clean appearance.

Protective cover that conceals the upper door hinge assembly on your refrigerator. Replace when cracked, broken, or missing to restore appearance.

Specs: Hex head ,1/4-20 x 5/8

This roller assembly consists of small caster-style wheels mounted on a support ring, designed to allow a shelf, drawer, or internal component to slide smoothly inside the refrigerator or freezer compartment. It supports the weight of stored items while enabling easy access. Replace this assembly if the rollers are cracked, seized, or if the shelf or drawer no longer glides properly and feels stuck or wobbly.

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.

Refrigerator won't power on or respond to controls? This main power control board distributes power to major components. Accessible behind kickplate.

The refrigerator electronic control board cover protects the main control circuitry and is located behind the temperature controls or inside the refrigerator. Replace when the cover is cracked, damaged, or doesn't fit securely over the control board.

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.

Secures panels, brackets, and handles in refrigerators and other appliances. Replace missing or stripped screws to restore secure mounting.

Adjustable leveling foot installs at the bottom of your appliance to ensure stability and proper leveling. Replace if broken, cracked, or missing.

White front grille kickplate for bottom-mount refrigerators. Covers the lower front panel beneath the door. Replace if cracked, discolored, or missing.

Grey plastic grille kickplate that covers the base of your refrigerator. Includes mounting clips. Replace if cracked, melted, broken, or missing.

Grey plastic grille kickplate that covers the base of your refrigerator. Includes mounting clips. Replace if cracked, melted, broken, or missing.

The lower hinge closing cam assists in the smooth closing action of the refrigerator door and helps maintain proper door alignment. Located within the bottom door hinge assembly, it should be replaced when the door doesn't close properly, swings open on its own, or requires excessive force to close.

Hex washer head ,10-32 x 0.375. Ground

This cover assembly attaches to the back or bottom of the refrigerator to enclose and protect the compressor and related components. It helps keep dust and debris away from the compressor area while providing a finished appearance. Replace this cover if it is cracked, broken, or missing, which can allow dirt buildup on the compressor and condenser that reduces cooling efficiency.

Fixes incorrect temperature readings and short cycling. This thermistor monitors fridge temps and signals the control board. Moderate DIY repair.

Replacement mounting screw for securing brackets, trims, covers, and components inside your refrigerator. Replace missing, stripped, or lost hardware.

Molded plastic evaporator cover that protects the freezer coil assembly and directs airflow. Replace if cracked, broken, or missing for proper cooling.

Refrigerator cover panel that conceals internal components or provides finished appearance. Replace if cracked, discolored, broken, or missing.

Replace your refrigerator's air duct if cracked, broken, or missing. This duct directs airflow between compartments for proper temperature control.

Fix a fridge that's freezing food or not cooling properly. This air damper controls cold airflow between compartments. Moderate DIY repair for most models.

Seals the air damper opening to maintain proper airflow between compartments. Replace if torn or compressed to fix uneven cooling and drafts.

This is a gasket that seals around the upper evaporator cover inside the freezer compartment. It helps maintain proper airflow and prevents warm air from bypassing the evaporator coils. Replace this gasket if you notice excessive frost buildup in the freezer, inconsistent cooling, or if the gasket appears torn, warped, or no longer seals tightly against the evaporator cover.

Seals refrigerator door to keep cold air in and warm air out. Replace if torn, cracked, or causing temperature issues. Verify fit with model number.

Secures the evaporator fan motor to its bracket for proper airflow. Replace if broken or missing to eliminate vibration, noise, or cooling issues.

Directs cold air from the evaporator through your freezer compartment. Snaps into the back wall. Replace if cracked, warped, or missing to restore airflow.

Replacement sump cover for bottom-mount refrigerators. Installs under drawers to protect components. Needed when original is cracked, broken, or missing.

The Screw Kit is an OEM part for Frigidaire appliances. It contains various screws specifically designed to fit and secure different components of Frigidaire appliances, ensuring a tight and secure assembly. This kit is essential for both initial installations and for making repairs or replacements to existing appliances, providing the necessary hardware to maintain or restore the structural integrity of your appliance.  These screws are #10-16 x .500 inches long and can be loosened or tightened using either a Phillips-head or square-head screwdriver.

Symptoms of needing a new Screw Kit include:

• Loose components or panels on your appliance due to missing or damaged screws.
• Inability to securely fasten parts during assembly or repairs, which can lead to operational issues or safety hazards.
• Screws stripping or corroding over time, which can compromise the stability and durability of the appliance.

Causes for replacing screws can include mechanical stress that causes screws to loosen or fall out, environmental factors like moisture leading to corrosion, or accidental damage during cleaning or maintenance.

This screw kit is designed to be universally compatible with various Frigidaire models, ensuring that you have the right screws for a range of repair needs.

Foam sleeve insulation that wraps around the refrigerator air duct. Replace worn, torn, or missing insulation to reduce condensation and moisture buildup.

Replacement wiring harness for refrigerators. Connects electrical components throughout the unit. Replace if wires are frayed, damaged, or connectors broken.

Foam insulation installs in refrigerator cabinet walls and interior surfaces. Replace if cracked, compressed, torn, or missing to restore efficiency.

Replace a cracked or missing protective trim cover on your refrigerator. This cover shields internal components from dirt and restores a clean look.

Secures refrigerator grille or trim to cabinet, preventing rattles and gaps. Replace when broken or missing to restore proper panel alignment. Verify fit with your model number before ordering.

Replacement screw for securing panels, components, and assemblies in appliances. Needed when original screws are stripped, lost, or damaged during repair.

Replacement screw that secures refrigerator door handles to the door. Needed when the original screw is worn, missing, or stripped, causing a loose handle.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Color: White

Replacement screw secures door handles, brackets, panels, and trim to refrigerator mounting points. Install when hardware is missing, stripped, or loose.

Replacement mounting screw for refrigerators and freezers. Secures shelves, handles, panels, and brackets. Replace missing, stripped, or rusted screws.

Replacement mounting screw for refrigerators and freezers. Secures shelves, handles, panels, and brackets. Replace missing, stripped, or rusted screws.

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head