Parts for Electrolux STF7000FS0: 05 - Cabinet / Top Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This inlet hose connects the household water supply to the refrigerator's water system so ice makers and dispensers receive a steady water feed. Durable, flexible tubing replaces worn or leaking supply lines to restore proper water flow. What it does:

• Channels incoming water from the home supply to the refrigerator's water valve and ice maker
• Replaces cracked, split, or leaking supply tubing that can cause reduced water flow or puddling
• Helps prevent leaks that can lead to water damage when original tubing fails
• Works with the fridge's internal water system to support ice and dispenser functions

• One inlet hose (single water supply line)

• Turn off the home water supply and unplug the appliance before servicing
• Inspect fittings for signs of corrosion; use the proper connector tools to avoid damage
• Tighten connections to a leak-free fit but avoid over-tightening plastic fittings

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This is a motor control board for a washing machine. It comes with the board, tape, bracket, and screw mounted on control. In most cases, this part is located on the bottom of the appliance near the drive motor. The purpose is to control the speed of the drive motor. It also works to determine the direction of the tumble and spin actions while a cycle is in process. If the washing machine is pumping but does not spin, this is often the result of a malfunctioning motor control board.If the motor control board has gone bad, it should be replaced. To replace it, make sure the washer is unplugged or the circuit breaker has been turned off. Pull the washer away from the wall, remove the knobs from the front and screws from the back, and lift the control panel. This offers access to the motor control board, which should be removed so the new part can be installed.This motor control board is made for use with washing machines by Electrolux, Frigidaire, Crosley, and Kenmore. It is sold on an individual basis. This is an authentic OEM replacement part that is directly sourced from the manufacturer.

The Front Loading Washer Door Lock and Switch Assembly is an OEM part for Frigidaire washing machines. This component ensures that the washer door is securely locked during operation, preventing leaks and interruptions, and also communicates with the control board to allow the wash cycle to start.

Causes of a bad door lock and switch assembly can include wear and tear from regular use, damage from forced door opening, electrical failures within the locking mechanism, or issues with the switch contacts.

Symptoms of a bad door lock and switch assembly include:

• The washer door not locking or unlocking properly
• Error codes related to the door lock
• The washer not starting its cycle
• Interruptions in the wash cycle due to door lock failures

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This replacement washer door window restores a clear view into the tub on compatible front-load models and helps the door seal correctly. Replace a cracked or cloudy pane to reduce leaks and keep operation safe. What it does:

• Provides the transparent viewing window in the washer door
• Works with the door boot/gasket to help form a watertight seal when closed
• Replace if the glass is cracked, chipped, shattered, or excessively scratched/cloudy
• Common symptoms include water leaking from the door area, poor sealing/door won't close, or visible damage to the window

• One door window glass

• Disconnect power and turn off water supply before servicing
• Wear cut-resistant gloves and eye protection; handle broken glass carefully
• Support or remove the door to a flat surface; separate door halves and transfer the window, noting orientation
• Clean the door boot sealing surface; seat the new glass evenly and reassemble without pinching the gasket; test for leaks

This inner door frame forms the interior half of the appliance door. It holds the window and mounting points so the door aligns and latches correctly, replacing cracked or warped plastic that can affect closing performance.

• Forms the interior structure of the door and supports the window
• Provides mounting locations for hinge, strike/catch, screws, and trim
• Helps maintain proper door alignment and seal contact when closed
• Damage can cause misalignment, difficulty latching, rattling/loose window, or a door that won't stay shut

• Disconnect power; if servicing a washer, also turn off the water supply
• Remove the door, place it on a padded surface, and transfer the window and any door hardware to the new frame
• Reuse existing fasteners; tighten evenly and avoid overtightening into plastic
• Verify the door closes and latches smoothly before returning the appliance to service

This machine screw secures panels, brackets, and internal components in compatible appliances. Replacing a missing, rusted, or stripped #10-16 x 3/4-inch screw restores a snug fit and helps keep assemblies properly aligned and quiet.

• Fastens panels, brackets, guards, or other hardware in appliance assemblies
• Replaces lost, corroded, or stripped mounting screws
• Helps reduce vibration and rattling from loose fittings
• Maintains proper alignment and secure attachment of components

• Disconnect power before servicing; turn off gas and/or water supply if applicable
• Note original screw locations and any spacers or clips for correct reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• Use the appropriate driver or nut driver; wear gloves and eye protection

The Door Strike is an OEM part for Frigidaire washing machines. It is a critical component that interacts with the door latch, securing the washing machine door during operation. This ensures that the door remains closed and locked throughout the washing cycle, preventing water leaks and maintaining the safety and integrity of the appliance. 

Symptoms of a bad Door Strike include:

• The washing machine door not closing or locking properly,
• The washer not starting due to the door not registering as closed,
• Visible signs of damage or wear on the strike, such as cracking or deformation.

Causes of door strike failure typically involve physical damage from forceful closing of the washer door, general wear from repeated use, or material fatigue.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Washer Door Hinge is an OEM part compatible with Frigidaire washing machines. This hinge ensures the door opens and closes smoothly and securely, maintaining a proper seal during operation.

Common causes of a faulty hinge include regular wear and tear from frequent use, corrosion due to exposure to moisture, or physical damage from accidental impacts. A damaged hinge can lead to improper door alignment, affecting the washing machine’s ability to maintain a watertight seal.

Symptoms of a bad washer door hinge include:

• Difficulty in opening or closing the door
• The door not staying in place or sagging
• Leaks from around the door area
• Visible signs of rust or damage on the hinge

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement screw secures appliance panels and components. With a #10-16 thread and 0.75-inch length, it replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and reduce vibration and noise.

• Fastens cabinet panels, brackets, or internal parts in washers and dryers
• Direct replacement for worn or lost screws to keep assemblies aligned and secure
• Helps address loose/vibrating panels, rattling noises, or visible gaps/misalignment
• Spec: #10-16 thread; 0.75-inch length

• Disconnect power; for washers, also shut off water supply
• Match the original screw location; start threads by hand to prevent cross-threading
• Use a driver that fits the screw head properly; tighten snugly without overtightening

This clip is a genuine General Electric part, sold individually. It can be used as a replacement part for a dryer or a washer/dryer combination appliance. This clip affixes the toe panel to the front panel of the dryer.This clip could become damaged within the standard lifespan of a dryer; this damage could take the form of nicks, scrapes, tears, punctures, or erosion to the plastic material that reduces its functionality for a dryer. If the toe panel is coming loose from the front panel of the dryer, the clip should be visually inspected and assessed for signs of damage. If the clip is damaged, it should be removed and replaced with this genuine OEM replacement part. The replacement process is simple and will require no special tools.This is an OEM part sourced directly from the manufacturer. It is sold individually. This clip is compatible with the following appliance brands: Frigidaire, Kenmore, Electrolux, Westinghouse, and Crosley.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This replacement control panel restores the appliance's front console and user interface so buttons and the display work reliably. It provides the visible face and mounting surface for controls and status indicators. What it does:

• Houses the appliance's buttons, touchpads, and display area so you can select settings and see status
• Replaces cracked, scratched, or cosmetically damaged panels that affect appearance or button access
• Helps when buttons are unresponsive due to a damaged front panel
• Restores a clean mounting surface for switches and overlays

• Disconnect power before starting any repair to avoid shock or injury
• Remove trim, bezels, or mounting screws as needed to access the panel; keep fasteners for reassembly
• Handle carefully to avoid scratching or cracking; use proper tools to release clips

This mounting bracket secures internal components or panels to the appliance, restoring proper alignment and support. Designed to replace a damaged or missing bracket so doors, drawers or internal assemblies sit and operate correctly. What it does:

• Provides structural support for panels, drawers or internal components
• Restores proper alignment to reduce rattling, sagging or binding
• Replaces broken, bent or missing brackets that prevent parts from seating
• Helps maintain safe operation by keeping components firmly attached

• One mounting bracket

• Disconnect power and water before starting repairs
• Use appropriate fasteners; retain any original screws if undamaged
• Inspect surrounding mounting points for damage and replace if needed
• Wear gloves to protect against sharp edges; test fit before final fastening

The Cord is an OEM replacement part for Frigidaire washing machines. Extending from the rear of the unit, it safely powers the washer through a connection to a wall outlet.

Causes of cord failure are normal wear from frequent coiling and plugging/unplugging motions over the appliance's lifespan. Rodents or sharp edges may also damage the outer jacketing.

Signs of a bad cord include:

• Exposed or severed copper wiring visible inside
• External cracks, splits or abrasions eroding the casing  
• Erratic behavior during the wash cycle
• GFCI/EGCI outlet tripping frequently

Compatible models also include Electrolux, KitchenAid, Jenn-Air, and Kenmore options. Maintaining safety is a top priority.

This bushing protects the appliance service cord where it passes through the cabinet, reducing wear and preventing chafing that can expose wiring. It's a simple replacement that restores a safe cord entry point. What it does:

• Cushions and centers the service cord at the cabinet opening to prevent abrasion
• Helps keep the cord from rubbing on sharp metal edges that can cause insulation damage
• Reduces risk of shorting, sparking, or intermittent power caused by a worn cord
• Commonly replaced when the existing bushing is cracked, missing, or deformed

• One service cord bushing

• Disconnect power (unplug or switch off breaker) before servicing
• Inspect the cord and surrounding insulation; replace the cord if damage is found
• Push the bushing into the cabinet opening, then route the cord through the bushing until seated
• Reuse only if undamaged; do not force a damaged bushing into place

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Leveling Leg is an OEM part for Frigidaire washers. It is designed to provide stability and level the appliance properly on the floor during installation and operation.

Common causes for needing to replace the leveling leg include damage or wear over time, which can lead to unevenness and excessive vibration during wash cycles.

Symptoms that may indicate the need for a replacement leveling leg:

• Uneven or unstable washing machine
• Excessive shaking or vibration during spin cycles
• Difficulty in leveling the washer during installation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This metric machine screw features an M5 x 0.8 thread used to secure panels and assemblies inside your appliance. Replacing missing or damaged hardware restores a tight, rattle-free fit and helps maintain proper alignment of parts.

• Fastens appliance components using an M5 x 0.8 machine-thread
• Replaces missing, loose, or stripped screws
• Helps reduce vibration and rattling noises
• Maintains correct alignment of brackets, panels, or internal assemblies

• Disconnect power before servicing; if working near water connections, shut off the supply.
• Match thread and length to the original screw and replace in the same location.
• Start threading by hand to avoid cross-threading; use the correct driver and do not overtighten.
• Reinstall any original washers or lock hardware used with the screw.

This part is a door assembly that is used on washing machine units. This assembly includes a variety of parts that make up the door itself. The purpose of the door is to keep the water inside of the tub from splashing outside but to also keep anything from falling into the washing machine.If the washing machine door assembly is cracked or broken, this is a high-quality replacement part. If the door hinge breaks, the door may fall off completely. The hinge may begin to sag which could cause the striker to break. Disconnect the washing machine from its power source before attempting to replace this part. The repair person can protect their hands by wearing gloves during this process.This part is sold individually and is sourced directly from the manufacturer. This particular washing machine door assembly is compatible with washing machines that are manufactured by the Frigidaire and Electrolux brands.

This dampener regulates airflow inside the refrigerator to help steady temperatures between compartments and reduce temperature swings. It replaces a worn or broken air control piece to restore proper circulation and consistent cooling. What it does:

• Controls airflow between fridge compartments to help maintain even temperatures
• Helps reduce warm or cold spots caused by stuck or broken dampeners
• Minimizes rapid temperature changes when doors open and close
• Operates quietly as part of the internal air distribution system

• Disconnect power to the appliance before starting any repair
• Basic hand tools may be required; handle plastic parts carefully to avoid breakage
• Verify correct orientation and secure mounting for proper airflow operation

This ring fits into its mating groove to retain or space a component within an assembly. It keeps parts aligned and secure so your appliance operates reliably under vibration and everyday use.

• Provides axial retention or spacing within the assembly
• Helps prevent parts from backing off or shifting during operation
• Common replacement when the original ring is bent, cracked, or missing
• Symptoms include looseness, rattling, or components not staying in place

• Disconnect power; shut off water if working on a water-carrying assembly
• Note the ring's orientation and groove location before removal
• Use the appropriate pliers or hand tools; avoid prying against delicate parts
• Ensure the ring is fully seated in its groove before reassembly and testing

Plastic door cover

This rubber grommet cushions and protects components by isolating vibration and preventing wear where parts pass through openings. It restores proper fit and reduces noise or rubbing caused by a worn or missing grommet. What it does:

• Cushions panels, housings, or shafts to reduce vibration and noise
• Protects wiring, hoses, or metal edges from abrasion where they pass through openings
• Keeps assemblies aligned by filling mounting gaps and securing components
• Common symptom: increased rattling, vibration, or chafing around the affected area

• One rubber grommet

• Disconnect power to the appliance before beginning any repair
• Remove panels or components as needed to access the grommet; hand tools may be sufficient
• Inspect surrounding parts and replace any damaged items
• Use the OEM-style grommet to ensure proper fit and function

This door switch senses whether the appliance door is closed and signals the controls to run only when it's safe. Replacing a worn or intermittent switch restores dependable starts and proper shutoff when the door opens. What it does:

• Detects door position and allows operation only when the door is fully closed
• Interrupts operation when the door opens for safety
• Common symptoms include: won't start, stops when the door is moved, or "door open" message/error
• Intermittent starts due to worn actuator or internal switch contacts

• 1 door switch

• Disconnect power before servicing
• Access the switch from the front or top panel; release mounting screws or tabs
• Move wires to the new switch one at a time to maintain correct positions, then secure the switch
• Test operation before reassembly

A small metal mounting screw used to secure appliance panels and internal components. Simple replacement that restores proper fit and reduces rattling or loose parts when the original fastener is missing or damaged. What it does

• Secures panels, brackets, or trim pieces to the appliance chassis
• Holds internal components in place to maintain alignment and function
• Helps prevent vibration noise and movement from loose parts
• Suitable where the OEM listed screw size and thread match the original

• Disconnect power and water before servicing
• Use the correct screwdriver or driver bit to avoid stripping the head
• Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
• Keep any removed screws organized to ensure correct reassembly

A small metal mounting screw used to secure appliance panels and internal components. Simple replacement that restores proper fit and reduces rattling or loose parts when the original fastener is missing or damaged. What it does

• Secures panels, brackets, or trim pieces to the appliance chassis
• Holds internal components in place to maintain alignment and function
• Helps prevent vibration noise and movement from loose parts
• Suitable where the OEM listed screw size and thread match the original

• Disconnect power and water before servicing
• Use the correct screwdriver or driver bit to avoid stripping the head
• Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
• Keep any removed screws organized to ensure correct reassembly

This shipping bolt kit, also called a shipping support kit, secures the washer's tub and suspension for safe transport. Install before moving or shipping the appliance to help prevent internal movement and damage, then remove before operating. What it does:

• Locks the wash tub in place to reduce movement during transit
• Helps protect against vibration and damage while the unit is moved
• Ideal when relocating or shipping the appliance; replaces lost original shipping hardware
• Not for normal operation—remove all shipping bolts before use

• One shipping bolt kit

• Disconnect power, turn off water, and move the appliance to access the rear.
• Insert bolts into the designated shipping holes and tighten evenly until snug; do not overtighten.
• Follow your model's installation guide for bolt locations and quantity.
• Before first use after transport, remove all shipping bolts and any spacers; save for future moves.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.