Parts for Ge CS980SN3SS: 01 - Control Panel Parts

This replacement knob assembly restores control of a range/stovetop burner by providing a secure, splined interface with the control shaft. It replaces a cracked, loose, or missing front burner control knob so you can adjust heat safely and accurately. What it does:

• Replaces a damaged or missing left-front or right-front control knob so the burner can be selected and adjusted
• Provides a secure fit on the control shaft to prevent slipping or accidental changes
• Helps eliminate cracking, chipping, or worn spline issues that make the knob hard to turn
• Restores tactile control for precise temperature selection

• One knob assembly for a left-front or right-front control

• Disconnect power to the appliance before starting; if the appliance uses gas, turn off the gas supply
• Pull the old knob straight off the control shaft; align splines and push the new knob firmly onto the shaft
• Test knob operation after installation; do not force if misaligned—re-seat and try again
• If control or switch is damaged, replace that component rather than forcing a knob onto a damaged shaft

Right-rear control knob for a range or cooktop — replaces a cracked, loose, or missing knob to restore reliable burner selection and improve user control. Simple push-on replacement returns secure turning and accurate zone selection. What it does:

• Replaces the damaged or missing right-rear range/cooktop control knob
• Provides a secure grip for turning the control shaft to select burner/heat settings
• Helps stop slipping, wobbling, or stripped-knob symptoms that prevent proper selection
• Matches the original knob shape to restore correct alignment and operation

• Always turn controls off and disconnect power (or shut off gas) before servicing
• Pull the old knob straight off the control shaft; align and push the replacement fully onto the shaft until secure
• Do not force the knob onto a damaged shaft; if the shaft or switch is worn, it may need repair or replacement

This center knob assembly replaces the worn or broken center control knob on the cooktop/console, restoring a secure grip and reliable control. It fits onto the control shaft to allow precise temperature and burner selection. What it does:

• Replaces a cracked, loose, or missing center control knob for reliable user control
• Restores proper fit and tactile feedback when turning stove or range controls
• Helps stop slipping or intermittent control contact caused by worn knobs
• Matches OEM shape for proper alignment and rotation on the control shaft

• Designed for user-replaceable installation; pull off the old knob and push this assembly onto the control shaft
• Ensure the appliance is turned off and cool before attempting replacement
• If knob is tight, pull straight and avoid twisting to prevent damage to the shaft

This oven thermostat monitors and regulates oven temperature so your range maintains consistent baking and roasting results. It replaces a failed or inaccurate thermostat to restore proper oven temperature control. What it does:

• Senses oven temperature and signals the heating element or burner to cycle on and off
• Helps correct ovens that run too hot, too cold, or have inconsistent temperatures
• Restores temperature regulation for better baking and cooking performance
• Works with oven control systems that use a mechanical/electromechanical thermostat

• 1 oven thermostat

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Access may require removing the oven control panel or inner back panel; follow your model's service manual
• Replace with the exact part number shown on your appliance or parts list to ensure fit and function

This is a replacement mounting screw for the refrigerator/freezer thermostat assembly. It secures the thermostat to the cabinet so temperature sensing and control remain stable and reliable. What it does:

• Secures the thermostat housing or bracket to the appliance cabinet
• Keeps the thermostat properly positioned for accurate temperature sensing
• Common fix when a loose, missing, or stripped thermostat fastener causes rattling or poor contact
• Small hardware part used during thermostat replacement or reassembly

• One thermostat mounting screw

• Turn off power to the appliance before starting any repair
• Use appropriate screwdriver and do not overtighten to avoid stripping the housing or threads
• If original hole or threads are damaged, inspect bracket or cabinet and replace as needed

This replacement indicator light lens covers the lamp opening on the control panel, protecting the opening while keeping the ON indicator easy to see. Replacing a cracked or missing lens restores visibility and a finished look.

• Covers and protects the indicator lamp opening in the panel
• Diffuses light so the appliance's ON status is easy to see
• Helps keep dust, grease, and moisture out of the control area
• Common signs to replace: lens cracked, missing, cloudy/discolored, or won't stay seated

• Disconnect power by unplugging the appliance or switching off the circuit breaker
• Access the panel area; release the old lens tabs or retainer from the back side and remove
• Align and press the new lens fully into the opening until it sits flush
• Restore power and verify the indicator illuminates correctly

This pilot indicator light mounts in the control panel and illuminates to show when a surface element or another heating circuit is powered. Replace a burned-out or stuck-on light to restore a clear, reliable power-on warning.

• Lights when the corresponding heating circuit is energized
• Alerts users that heating components are active
• Common symptoms: light does not turn on, stays on constantly, flickers, or is very dim
• Shows physical damage to the lens or terminals when failed

• Disconnect power at the breaker before servicing
• Remove the backguard or control panel cover to access the indicator light from behind
• Note wire positions; move connectors to the new light one at a time and secure the light in the panel
• Restore power and test operation before reassembly

The Infinite Control Switch is an OEM part for GE ranges and cooktops. This switch regulates the heat levels of the burners, allowing users to adjust the cooking temperature to their desired setting. It ensures that each burner provides consistent and controllable heat for precise cooking.

Causes of a bad infinite control switch can include regular wear and tear, electrical surges, or damage from spills and splashes. Over time, these factors can lead to the switch malfunctioning, which may result in poor temperature control or complete failure of the burner.

Symptoms of a bad infinite control switch include:

• The burner not heating up or heating inconsistently
• The burner staying on high heat regardless of the setting
• Difficulty adjusting the burner temperature
• The switch feeling loose or unresponsive

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This control switch activates the surface-burner spark ignition when you turn the knob to Lite. Replacing a worn switch restores consistent lighting and can stop unwanted, continuous clicking caused by a stuck switch. What it does:

• Closes the ignition circuit to the spark module to light a surface burner when the knob is turned
• Typical symptoms: no spark from a specific knob, intermittent ignition, or continuous clicking with knobs in the Off position
• Heat, spills, and moisture intrusion can damage the switch over time

• 1 control switch

• Disconnect power and shut off gas; allow the appliance to cool before servicing
• Remove the knob and front/top panel as needed to access the switch on the burner valve
• Transfer wires one at a time to the new switch; mount in the same orientation and secure
• Restore power and gas; test for proper spark at each burner before reassembly

This infinite switch center is the replacement control assembly that regulates heat levels for an electric cooktop surface burner, restoring adjustable temperature control and reliable cycling. Ideal when a surface element fails to change settings or heat properly. What it does:

• Controls the variable heat settings for a surface burner so you can select low-to-high temperatures.
• Regulates on/off cycling of the element to maintain the chosen heat level.
• Commonly replaces units that cause a burner to not heat, stay on high, or not respond to the knob.
• Works as the central switching assembly for the affected surface element control circuit.

• One infinite switch center assembly.

• Disconnect power to the appliance at the breaker or unplug before starting any work.
• Use proper tools and take care removing the cooktop or control panel to access the switch; follow the appliance's service instructions.
• Verify terminal locations and wiring match the replacement before connecting.
• After installation, restore power and test all settings.

This electronic oven control (ERC3HP) replaces the console control board that manages oven functions and user interface, restoring timed baking, broiling, and temperature control for compatible GE ranges and wall ovens. What it does

• Regulates oven temperature by controlling bake and broil elements and sending/receiving signals from the oven sensor
• Operates the front display, clock, touchpad/buttons, timers, and oven mode selections
• Helps resolve symptoms like an unresponsive keypad, blank or erratic display, or incorrect oven cycling
• Can clear control-related error codes when the underlying board has failed

• 1 electronic oven control module (ERC3HP)

• Disconnect power to the appliance at the circuit breaker before starting work
• Handle the control by the housing; avoid touching circuit traces and connectors to prevent damage
• Use basic hand tools to remove the console/inner panel; note wiring locations or take a photo before disconnecting

This knob assembly replaces a damaged or missing control knob so you can reliably turn the appliance's control shaft and select settings. A new knob restores proper fit, smooth operation, and a clean, like-new appearance.

• Attaches to the control shaft to adjust temperature, burner, or other settings
• Restores a secure fit and consistent feel while turning the control
• Replaces cracked, stripped, or missing knobs to bring back precise control
• Common symptoms: knob broken, wobbly, spins without turning the shaft, or falls off

• Disconnect power; for gas appliances, also shut off the gas supply
• Pull the old knob straight off the shaft—do not pry against the panel
• Align the new knob with the shaft and press straight on until fully seated
• Test knob operation to ensure smooth turning and proper engagement

The Skirt is an OEM replacement part for GE cooktops and ranges. It is a trim piece designed to enhance the aesthetic appearance of the appliance and provide a secure fit around the cooktop or burner area. This part also helps protect internal components by covering gaps and exposed areas.

Causes of a damaged skirt can include accidental impact, heat-related wear, or improper cleaning methods. Over time, the material may warp, crack, or become discolored, detracting from the appliance’s appearance and functionality.

Symptoms of a bad skirt include:

• Visible cracks, chips, or warping
• Loose or detached trim around the cooktop
• Gaps exposing internal components
• Difficulty securing the skirt in place

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This glass and touch board assembly replaces a cracked or unresponsive touch control panel and restores reliable user input and display functionality on compatible oven/range consoles. It provides the glass panel with the integrated touch circuitry needed for controls to work properly. What it does:

• Replaces damaged or cracked control glass and the integrated touch-sensor board
• Restores responsive touch keys and consistent control input
• Fixes symptoms like unresponsive buttons, intermittent commands, or missing display/indicator feedback
• Provides the factory-style panel and electronics that interface with the range control board

• Disconnect power to the appliance before beginning any repair to avoid shock hazard
• Handle the glass panel carefully to avoid chipping or cracking; wear gloves and eye protection
• Some disassembly of the control console is required; keep screws and trim organized for reassembly