Craftsman String Trimmer Parts

Air cleaner assembly cover for gas line trimmers. Protects the air filter from debris and damage. Replace if cracked, broken, or missing to maintain proper filtration.

Complete carburetor assembly for gas string trimmers. Mixes air and fuel for engine combustion. Replace if cracked, corroded, or leaking fuel.

This electronic component generates the spark for engine ignition in gas-powered line trimmers, mounted near the spark plug. Replace it when the trimmer won't start, has difficulty starting, or runs erratically.

Replacement fuel cap for lawn tractors, trimmers, blowers, and tillers. Prevents fuel leaks and evaporation. Replace if cracked, broken, or missing.

Replacement throttle trigger spring for gas line trimmers. Installs inside the throttle trigger assembly. Needed when original spring is broken or missing.

Rope won't retract after pulling? This recoil starter spring restores proper rope tension in lawn equipment engines. Essential starter assembly component.

If your mower won't start or turns over but won't crank, the ignition switch may be faulty. This key-operated switch controls electrical power.

Flange bearing for lawn tractors and snow blowers. Replace if you notice excessive noise, vibration, or rough wheel rotation. Verify fit with your model.

This is a bushing made from black plastic with a cleft down the middle to provide enough flex for easy insertion. It has a flanged design, which means it won’t easily pop out after installation, even under stress from constant vibration. The bushing’s primary purpose is to protect wires and cables from damage as they pass through a channel. As such, the material is fairly durable and does not need to be replaced under ordinary circumstances. That said, there are some situations in which it can become damaged. For one thing, it’s easy to damage while repairing the wires or cables that run through the bushing. If the bushing does need to be replaced, it requires disconnecting any cables or wires that run through the bushing. Pop out the old bushing with a rubber mallet, install the new bushing the same way, reconnect the wires, and the repair is complete. This is an OEM part sourced directly from MTD, and it is sold individually. It was initially used on snowblowers but has also been used on lawnmowers and lawn tractors.

A ball bearing is a common type of rolling-element bearing. It will use balls to keep space between the bearing races and eliminate friction and contact between moving parts. Ball bearings used in lawn and garden equipment ensure that axial loads and radial loads are evenly supported and that there is only a limited amount of rotational friction on the component. It distributes weight evenly, but will undergo constant wear and tear from vibration, heat, and friction and will need replacement regularly. This ball bearing is a genuine OEM part suited to use in Craftsman, Cub Cadet, Ryobi, Troy-Bilt, MTD, Huskee, Yard Machines, Bolens, Mastercut, and Yard-Man equipment. It may be needed for repair work done on a lawnmower, snowblower, tiller, edger, or a log splitter.

Starter rope won't retract after pulling? This recoil pulley and spring assembly fixes rope retraction issues on mowers and small engines. Direct fit.

This genuine OEM Part is a choke temperature control rod for lawnmowers. The choke temperature control is the metal piece that regulates the choke temperature allowing for it to function properly within a lawnmower. If the choke function is no longer working efficiently, it might be time to replace the choke temperature control. Luckily, replacing this part is a simple repair.Before beginning, make sure the engine is cool to avoid getting burned. Locate the old choke temperature control rod and remove the screws to the mounting assembly that hold the rod in place. Once removed, lift the old choke temperature control out and away from the mower and set it to the side. Replace with the new control rod and secure the mounting screws. Start up the mower to see if the choke function is working properly. If it does, the installation was a success. This replacement part is sold individually and is compatible with MTD brand lawnmowers.

Reel spool assembly for gas line trimmers. Holds and feeds trimmer line during operation. Replace if spool is cracked, worn, or missing components.

Blade spindle assembly houses the shaft that spins the mower blade. Replace if cracked, bent, or worn from impact damage or normal wear.

Replace a worn drive sprocket if your chainsaw chain won't rotate or moves sluggishly. Simple installation in 15-20 minutes with basic tools.