Crosley Range Parts

Restore reliable heat to your electric range or cooktop with this surface heating element. Replacing a failed top-burner element brings back consistent, even heating so pots and pans heat up properly at your chosen setting.

• Supplies electric heat to a cooktop burner zone when turned on
• Common fix for a burner that won't heat or only partially glows/heats
• Helps address uneven or slow heating on the affected element
• Replace if the element shows visible breaks, blisters, or has shorted

• Disconnect power at the breaker and allow the cooktop to cool completely before service
• Access varies by model; support and protect glass tops when lifting/removing
• Photograph wiring; transfer any original brackets, insulators, or limiter/thermostat if present
• Ensure clean, tight terminal connections; fully reassemble before restoring power

This surface heating element powers one of your range's top burners, restoring steady, responsive heat for everyday cooking. Replace a failed element to bring your cooktop back to consistent performance when boiling, simmering, or sautéing.

• Provides heat to the selected surface burner when the control is turned on
• Works with the burner switch to reach and maintain set temperatures
• Common symptoms of failure: burner won't heat, heats unevenly or intermittently, or shows visible damage/hot spots
• Helps resolve long heat-up times and inconsistent cooking results

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing.
• Access and mounting vary by model; note wire locations and transfer any brackets/clips from the original element.
• Inspect terminals and connectors; replace any heat-damaged wiring or receptacles before reconnecting.
• Handle by the frame and avoid stressing the element; ensure secure electrical connections before testing.

This left-side oven door hinge supports the door and controls its spring-loaded movement so it opens smoothly and closes firmly, helping maintain a tight seal and consistent cooking performance.

• Provides spring tension and a pivot point for controlled opening and closing
• Aligns and pulls the door fully closed against the gasket
• Restores smooth, even door movement
• Common symptoms of a worn hinge: door won't close fully or sags; slams/falls open; feels loose or stiff; heat escaping or oven light staying on

• Disconnect power and let the oven cool completely before servicing
• Support the door; engage hinge locks or remove the door at the stop position per your model
• Springs are under tension—use gloves and caution
• After installation, verify alignment and that the door closes and seals properly

This surface burner ignitor/orifice assembly directs gas through a calibrated orifice and provides the spark to ignite it. Replacing a worn or damaged assembly restores consistent lighting and an even flame on the affected rangetop burner.

• Routes gas from the valve through the orifice to the burner head
• Positions the ignitor for reliable sparking and quick ignition
• Helps maintain correct flame size and pattern on that burner
• Common symptoms: burner won't light, clicks without flame, delayed ignition, weak or uneven flame

• Disconnect power and shut off the gas supply before servicing
• Remove grates, caps, and burner heads; lift the cooktop to access the assemblies
• Note wire routing and original orifice location; transfer any reusable hardware from the old part
• After installation, restore gas and check connections for leaks, then test spark and flame

This replacement fan blade mounts to the appliance's fan motor to move air as designed. Installing a new blade restores proper airflow and helps reduce vibration or noise caused by bent, cracked, or worn fins. What it does

• Attaches to the fan motor shaft to move air through the cavity or across internal components
• Supports even air circulation or cooling performance, depending on model
• Helps resolve issues such as loud scraping/whirring, vibration/wobble, weak airflow, or visible blade damage

• One fan blade

• Disconnect power at the breaker and allow the appliance to cool completely before servicing
• Access the fan assembly from the rear panel or inside the oven behind the fan cover (varies by model); wear gloves—edges can be sharp
• Note blade orientation/rotation and securely reinstall using the original fastener(s)
• Hand-spin the blade to ensure clearance and free movement before reassembly and testing

This replacement seal restores a tight barrier between mating parts in your appliance, helping contain air, moisture, or fluid so the unit operates efficiently and reliably over time.

• Provides a compressible barrier between components to prevent escaping air or liquids
• Helps maintain proper performance when the original seal is worn or deformed
• Common symptoms include poor sealing, seepage around a joint, or visible cracks/flattening
• Replace if cut, brittle, misshapen, or no longer seats securely

• Disconnect power; shut off water or gas supply before servicing
• Note the seal's orientation and seating depth before removal
• Clean mating surfaces and grooves; avoid sharp tools that could damage the new seal
• Seat the new seal evenly all the way around; reassemble and test for a proper seal

The LP Gas Conversion Kit is an OEM part for Whirlpool appliances. This kit allows for the conversion of natural gas appliances to use liquid propane (LP) gas. It includes all necessary components, such as orifices and instructions, to ensure a safe and efficient conversion.

Over time or due to specific needs, you might need to convert your appliance from natural gas to LP gas. Causes for needing this conversion include moving to an area where only LP gas is available or preferring LP gas due to its efficiency and environmental benefits.

Symptoms indicating the need for a gas conversion kit include:

• Moving to a location that only supplies LP gas
• Changing energy preferences for better efficiency
• Appliances set up for natural gas needing adaptation to LP gas

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Anti-Tip Bracket Kit is an OEM part for Frigidaire ranges and ovens. This part secures the appliance to the floor or wall, preventing it from tipping over when the oven door is opened or when heavy cookware is placed on an open door or extended rack. The kit typically includes a metal bracket, screws, and installation instructions.

Over time, or during instances of moving or remodeling, the anti-tip bracket may become dislodged or may not be reinstalled correctly, which can compromise the safety of the appliance. 

Symptoms of a missing or improperly installed Anti-Tip Bracket include:

• The range or oven tilts forward when pressure is applied to an open door
• The appliance moves more easily than expected when nudged or cleaned
• Visible absence of a bracket at the lower back portion or floor area behind the appliance

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This assembly combines the spark igniter electrode with the orifice holder for a gas cooktop burner. It restores quick, reliable lighting and consistent burner performance when the original igniter/holder is cracked, shorted, or corroded. What it does:

• Generates the spark to ignite the surface burner gas
• Supports and positions the orifice to deliver gas to the burner head
• Helps resolve no-ignite, intermittent, or delayed ignition at a single burner
• Replaces cracked ceramic, shorted electrodes, and damaged orifice holders

• One surface burner igniter and orifice holder assembly

• Disconnect power and shut off gas supply before servicing
• Remove burner cap and head, then unfasten and lift out the old assembly
• Reconnect the spark wire and mount the new assembly; route the lead away from heat and sharp edges
• Restore gas and power; leak-check connections with an approved solution and verify proper ignition

This replacement surface burner head restores a steady, even flame on your gas cooktop. It mixes gas and air and distributes the flame evenly to help ensure reliable ignition and consistent cooking performance.

• Mounts over the orifice and channels gas/air through flame ports for even heating
• Helps resolve weak, uneven, or yellow flames and delayed ignition
• Can address clicking without lighting or burners that won't stay lit
• Durable cast construction designed for repeated heating cycles

• Disconnect power and shut off gas; allow the appliance to cool completely
• Remove grates and access the burner per your model; transfer any mounting hardware from the old part if needed
• Seat the new burner head squarely over the orifice and ensure proper alignment
• Restore gas and power; test for proper ignition and flame. If any gas connections were disturbed, check for leaks with soapy water.

The Surface Burner Cap is an essential OEM component for Frigidaire gas cooktop ranges. It regulates flame spread and directs heat precisely to pots and pans placed above each burner coil.

Causes of burner cap failure include warping or discoloration from continuous exposure to open flames and high cooking temperatures over time. Accidental impacts could also crack or fray burner cap edges.

Symptoms of a faulty burner cap include:

• Irregular or uneven flame patterns beneath cooking vessels   
• Visible yellow or blue flames indicating poor combustion  
• Signs of cracked porcelain or scorched burner bases
• Reduced burner efficiency and poor heat distribution

This authentic OEM replacement is compatible with Electrolux, Gibson, Kelvinator and select Kenmore models. 

This surface burner mounts on the cooktop and directs gas to produce a steady, controllable flame. Replace a worn or clogged burner to restore fast ignition and consistent heat from your range's top burner positions.

• Mixes and distributes gas to create the surface cooking flame
• Works with the spark igniter/electrode for reliable lighting
• Helps maintain an even flame pattern and stable heat
• Symptoms can include weak or uneven flames, yellow tips, delayed ignition/repeated clicking, or a burner that won't light

• Disconnect power and shut off the gas supply before servicing
• Remove the grate and burner cap, then lift off the old burner; clean the mounting surface
• Align the new burner with the igniter/electrode and locator features; ensure it sits flat and centered
• Reassemble, restore gas/power, and test for proper ignition and a clean, stable flame

This replacement thermostat is a temperature-sensitive switch used in select cooking appliances. It opens or closes at a fixed setpoint to control or limit heat, helping protect components and restore dependable operation of the affected circuit. What it does:

• Senses temperature at its mounting point and opens/closes electrical contacts at a designed setpoint
• Controls power to a heating or related circuit (such as an element or fan) to maintain safe operation
• Helps prevent overheating and protects internal components
• Failure can cause no heat, heat that shuts off prematurely, or a related circuit that won't turn on/off

• 1 thermostat

• Disconnect power to the appliance before servicing
• Access location varies by model; refer to your service manual for exact placement
• Move wires one at a time from the old part to the new to maintain correct connections
• Reinstall in the same orientation; ensure firm mounting for proper temperature sensing and secure electrical connections

The Door Handle Kit is an OEM replacement part for Frigidaire ovens and ranges. These handles provide safe access to the oven interior.

Causes of a bad handle kit can include normal wear over time of moving parts, accidental damage from impact or mishandling of the oven door, or issues with the latching mechanism.

Symptoms of a bad oven door handle kit include:

• Loose, sluggish, or difficult operation of handles
• Handles detaching from oven door
• Inability to fully open or close the oven door
• Problems with door sealing or staying closed securely

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This spark module powers the surface-burner ignition on gas ranges and cooktops. It generates high-voltage pulses to the electrodes so the burners spark and light when a knob is turned, restoring quick, consistent ignition.

• Sends high-voltage pulses to each surface burner igniter when a burner switch is turned on
• Centralizes spark for multiple burners; a failure often affects more than one burner
• Common symptoms: no clicking/spark on any burners, multiple burners won't light, weak or intermittent spark, continuous clicking from the ignition system
• Helps restore reliable lighting without using matches

• Disconnect electrical power and shut off gas before servicing
• Note wire locations; transfer leads one at a time to matching terminals on the new module
• Mount securely in the original position and ensure proper grounding
• After installation, verify spark at each burner before restoring full operation

Restore reliable lighting. This ignitor wire harness carries power from the ignition control to the ignitor, replacing cracked or shorted wires that cause weak/no spark or glow so your burner or oven can ignite consistently.

• Provides the dedicated electrical path between the ignition control and the ignitor
• Replaces heat-brittled, cut, or shorted leads to maintain proper insulation
• Helps address: burner or oven won't ignite, intermittent ignition, ignitor won't spark or glow
• Visual clues can include scorched insulation or corroded connectors

• Disconnect power and shut off gas; allow the appliance to cool completely before servicing
• Note original routing and connections; move one connector at a time to avoid cross-wiring
• Route wires away from sharp edges and hot surfaces; secure with original clips/ties
• Ensure all connections are fully seated, then restore power/gas and test ignition