Crosley Refrigerator Door

The Dairy Door is an OEM replacement part for  Frigidaire side-by-side refrigerators. Located inside the fresh food compartment, it provides a dedicated storage area for milk, yogurt, cheese and other dairy products requiring colder temperatures. The door measures approximately 9 inches wide and 5 inches high.

Causes of a bad dairy door include normal wear from repeated opening and closing over time. Exposure to spills inside the refrigerator can also potentially damage door shelf components or seals.

Symptoms of a bad dairy door are: 

• Difficulty opening or closing the door smoothly  
• Door alignment issues where it does not sit flush in the frame
• Leaks or moisture inside the dairy storage area
• Damage or cracks in shelf supports or gasket seals

This OEM part is also compatible with models from brands like Electrolux, Gibson, and Kelvinator brand models.

NOTE: For white use 240337701

The Compartment Door is an OEM component for Whirlpool and Kenmore built-in refrigerator models. It provides access to organized storage in the fridge's fresh food compartment. The compartment door measures approximately 15” long by 6” wide.

As a high-use access point, the door endures constant opening/closing stresses. Over extended periods, normal wear gradually reduces the quality and integrity of its cushioned sealed closure.

Symptoms include:

• Difficulty fully closing/latching the compartment door 
• Loud squeaking or sticking during operation

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Dairy Door is an OEM replacement part for Frigidaire side-by-side refrigerators. As the access point to the dedicated dairy compartment, the door is designed with precision seals to maintain optimal humidity levels inside. This helps keep dairy and other perishable items fresh longer.

Causes of a bad dairy door can include worn or damaged seals, dents or impacts warping the door frame, or issues with the electronic components that control humidity levels.

Symptoms of a bad dairy door include: 

• Excessive frost or ice buildup inside the dairy compartment   
• Difficulty opening and closing the door smoothly  
• Warm or dried-out dairy products despite a cold refrigerator interior
• Moisture leaks around the door seals  

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore side-by-side models.

The Flipper Mullion Assembly is an OEM part for Frigidaire refrigerators. It is an exterior part that seals the refrigerator door and houses the water and ice dispenser on select models. The flipper mullion assembly attaches both side by side doors together and operates the dispenser and door functions.

Causes of a bad mullion assembly can include damage from door impacts, wear from years of door swing motions, or failure of seals or gaskets.

Symptoms of a bad Flipper Mullion Assembly include:

• Gaps or air leaks around the refrigerator doors when closed
• Loose, sagging or misaligned doors
• Dispenser components like the water valve not functioning properly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
 

The Dairy Tray Door is an OEM part for Frigidaire refrigerators. This component is designed to cover and protect the dairy compartment, providing an optimal storage environment for dairy products like butter and cheese by maintaining a consistent temperature and preventing odors from other foods from contaminating them. This door no longer has graphics. For clear use 240337712

Causes of a bad dairy tray door can include wear and tear from regular use, physical damage from overloading or mishandling, and the plastic becoming brittle over time due to exposure to cold temperatures.

Symptoms of a bad dairy tray door include:

• Cracks or breaks in the door
• Difficulty in opening or closing the door
• The door not staying securely closed
• Visible warping or damage to the door

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Flipper Mullion is an OEM part for Frigidaire refrigerators. As the panel separating the fresh food and freezer compartments, it flips up for access while also providing an insulating barrier. 

Causes can range from normal wear and tear on hinge mechanisms to cracks or breaks from accidental impacts over years of use.

Symptoms of a bad flipper mullion include:

• Difficulty or resistance when trying to open
• Improper sealing between compartments, leading to air and temperature leaks
• Visible wear, cracks or damage to the component over time

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Color: clear. Measures about 11 inches wide by 7 inches high.

This replacement guide aligns and supports a moving component so it travels on its intended path without binding. Replacing a worn or broken guide restores smooth operation and helps prevent scraping, jamming, or premature wear of connected parts.

• Keeps the associated rack, drawer, or panel centered and properly aligned during movement
• Provides a track/stop for the mating part to follow
• Reduces friction and noise for smoother sliding
• Typical failure signs: sticking, uneven travel, scraping noises, or visible cracks/broken tabs

• Disconnect power; also shut off water or gas
• Remove the associated assembly to access the guide and note its orientation
• Reuse original screws/clips and tighten securely without overtightening
• Test movement after installation; replace worn mating rails or rollers if needed

This is the vertical flipper mullion assembly that mounts to one fresh-food door and pivots closed to seal the center gap when both refrigerator doors are shut, helping maintain proper temperature and energy efficiency.

• Creates the center seal between French-door refrigerator doors
• Helps prevent warm air infiltration and moisture/condensation in the fresh-food section
• Common failure signs include a loose or broken hinge, mullion not staying aligned, condensation at the door center, or doors not sealing properly
• May also be noted if doors pop open or temperature fluctuates in the refrigerator compartment

• Unplug the refrigerator before servicing
• Remove door bins to access mounting screws/clips
• Transfer any original covers or hardware if not part of the new assembly
• Verify proper hinge engagement so the mullion flips and seals smoothly before restoring power

This ice compartment door closes off the ice storage area inside the freezer, helping contain cold air and keep ice clean. Replace a cracked or warped door to restore a proper seal and easy access to the bin.

• Covers the ice compartment opening to help maintain temperature around the ice bin
• Hinged panel provides convenient access to the ice container
• Helps minimize frost and moisture at the compartment opening
• Common signs it's needed: cracked/missing door, broken hinge tabs, won't stay closed, frost buildup, or ice clumping near the opening

• Disconnect power to the refrigerator before servicing
• Remove screws, pins, or clips securing the old door; note hinge orientation
• Transfer any reusable hinge pins, latches, or trim from the original if required
• Install and align the new door; confirm smooth operation and a tight closure

The Mullion is an OEM part for Frigidaire refrigerators. It is situated between the freezer and refrigerator doors to separate the two compartments. The mullion provides structure, sealing the doors against air and temperature leakage.

Causes of a bad mullion can include wear and tear over time, damage from frequent door opening and closing, or impact damage.

Symptoms of a bad mullion include:

• Air and temperature leakage between compartments
• Difficulty closing one or both doors securely
• Gaps or cracks seen around the mullion frame
• Scratches, dents or other physical damage

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This small permanent magnet is used in supported refrigerator assemblies to actuate a mating reed switch or metal keeper. It helps the appliance recognize a closed position or hold a light cover/door closed for proper operation. What it does:

• Works with a reed switch or ferrous keeper to provide position sensing or magnetic latching
• Helps ensure features dependent on closed position operate correctly
• Can resolve issues where a small cover or door won't stay closed
• Address erratic "door ajar" indications tied to magnetic sensing

• Disconnect power and water before servicing
• Note the original magnet's location and orientation; polarity matters for proper operation
• Seat the magnet fully in its pocket or holder and align with the mating switch/keeper
• Test the related function before reassembling panels and trim

This piece replaces the flip-up cover for the cheese/butter compartment on your refrigerator door. It restores a tidy, enclosed spot for butter and small dairy items, helping keep contents contained and easy to access.

• Covers the dairy bin on the fresh food door; flips up for quick access
• Helps contain and protect butter/cheese items to reduce spills and mess
• Replace when cracked, warped, missing, or no longer stays attached/closed
• Designed to fit the designated hinge points for the dairy compartment on applicable models

• Disconnect power before servicing
• Allow plastic parts to warm to room temperature to reduce risk of cracking
• Align door tabs with the hinge posts on the compartment and press until fully seated
• Open and close the door to ensure smooth operation

This inner door panel replaces the plastic liner on the inside of a refrigerator or freezer door, restoring a clean interior surface and providing mounting points for bins and shelves. It helps stop air leaks and improves door appearance. What it does:

• Replaces a cracked, warped, or damaged door liner to restore structural integrity and appearance.
• Provides mounting surfaces for door bins, shelves, and gaskets so accessories fit and seal properly.
• Helps maintain proper door sealing by restoring the inner surface and alignment.
• Reduces the risk of moisture intrusion behind the liner that can cause odors or mold.

• High-level task: usually removes and installs from inside the door after removing door trim and hardware; follow manufacturer instructions.
• Use correct replacement fasteners and gaskets; do not overtighten screws to avoid cracking the liner.
• Work with the door supported to prevent dropping or bending; two-person assistance may be helpful for larger doors.
• Disconnect power if required by the manufacturer before removing door components to avoid electrical hazards.

This replacement inner door panel restores the interior surface of the door. It supports door bins/shelves and provides a stable surface for the door gasket to seal, helping keep cold air in and items secure.

• Forms the interior face of the door and supports door bins/shelves
• Provides the gasket with a flat surface to help maintain a proper seal
• Replace if cracked, warped, or separating from the door frame
• Common symptoms include loose/falling door bins, visible damage, or air leaks/frost near the door

• Disconnect power and empty items from the door before service
• Remove the door per the appliance manual and lay it flat to prevent twisting
• Transfer the door gasket and any reusable hardware from the old panel if applicable
• Install the new panel and tighten fasteners evenly; verify the gasket seals all around

Access door provides a finished cover for the appliance's service opening, protecting internal components from dust and damage while keeping the unit looking tidy and allowing access for maintenance and repairs. What it does:

• Covers the service or access opening and protects wiring, valves, and other internal parts.
• Allows access to controls, connections, or components for inspection and repair without removing major panels.
• Helps prevent debris, pets, or fingers from contacting internal parts.
• Replace a missing, cracked, or damaged access door to restore appearance and reduce exposure of internal components.

• Always disconnect power (and gas for gas appliances) before removing panels or working on the appliance.
• Handle the door and surrounding edges carefully to avoid cuts; keep original fasteners and reuse if undamaged.
• Align tabs/clips and secure with manufacturer screws; do not overtighten.