Crosley Washer Dryer Combo Parts

• Takes too long to dry

Get some acetone at a Hardware Store before you start. A pint will do. Unplug the dryer from 110 VAC. Pull the top off of the dryer, by lifting it from the front first. It is attached with snap metal fittings. Do not completely remove the top, just tip upright to gain access to the front interior of the dryer. Before you pull any wires from the door switch, record which color wires go to which terminals on the door switch. If you reassemble the connections incorrectly, the gas value will... Read more

The blower wheel center was worn down and spinning freely on shaft. Removing front covers, controls and brackets gave access to blower, which front half came off removing screws. (One screw underneath bracket) Pushed new blower on. (It's keyed and has small tabs that line up with groove on shaft). Installed clamp, reassembled and tested. Don't forget to pull the plug out before working on any appliance. Read more

• Spins slowly

With more difficulty and frustration than expected but it works fine now. Things learned: 1. Order only 3 replacement pins. One comes with the shocks that you can't be sure you see in the picture. 2. A circuit board in a plastic box mounted to the floor, left rear, must be removed by two screws to be able to get pliers onto the head of the pin more easily. This helps installation too. 3. A 1/2" deep socket pushed onto the retaining tab of the pin stays there while you pull with pliers from the... Read more

I replaced the spin bearing, tub seal, washer and drive belt since I had it all apart. The video was extremely helpful...I would have tore the whole thing apart trying to figure out how the agitator came off....but it was very simple. Read more

• Door won't close
• Shuts off too soon
• Doesn't shut off
• Takes too long to dry

Ordered a new clip and installed it. Easy to do. Unplugged the dryer. Removed the front. It is only held on by two screws. Removed wires to the door switch. removed the female end (it had the broken male piece in it. Inserted the new female part in the front, clipped in the male part into the door and reconnected the door switch wires, screwed the front back on. Job done. Total time was less than 10 minutes. Works like new. Read more

The old knob was not repairable. I ordered a new knob for the washer dryer stack unit. The order came within two days of ordering and it was the correct part. I was pleased. Read more

Replaced springs and shocks. Read more

I watched the helpful diy video. It gave me what the problem was and the confidence to do it. Took my dryer apart with the helpful hints in the video repair went smooth. Works like a dream and I saved money. Thank you appliance parts pros. Read more

• Timer will not advance

I replaced the timer Read more

Our washer is next door the bathroom. So when, during the rinse cycle, the hose split and we found the back of the house completely flooded I initially assumed the culprit was either the toilet or the sink or possibly an interdimentional portal into a demonic netherworld of vaguely chlorine scented water. I spent the next hour mopping it all up and checking and re-checking the pipes in the bathroom with no apparent leaks. The next load of laundry left more clues as this time the flood was from... Read more

Pushed new knob on Read more

I replaced the door boot with a new one from AppliancePartsPros.com. The most difficult part was starting at the back end of the new boot onto the stationary rim, just in front of the tub. And then anchoring it in place with the existing spring from the previous boot. To start the boot I had to hook the top edge of the boot, where the arrow tab is, onto the rectangular projection on the tub rim and then roll the rubber boot edge down around the tub rim and hope the rim was going into the... Read more

After watching YouTube videos on possible cause, went to appliancepartspros and order seal and leveling legs since the had been missing since machne was given to us. Parts came in within the week and replaced . No more leaks!! Read more

I changed the pump and also discovered the coin trap was wearing thin because it was rubbing against the sheet metal. So I replaced that as well. It took about 15 minutes to remove the coin trap and pump and about 20 minutes to install. The shipping was amazingly fast. I received the parts the next morning. I'm talking I ordered the parts before noon, chose the "fast shipping" option and received parts the next morning around 8:30 AM. Read more

Ordered a new handle from appliancepartspros.com and installed. Read more

Replacing the timer, timer knob, dial timer, Read more