Need Help?
Call or text
Refrigerator not cooling or clicking but not starting? The compressor start device initiates cooling. DIY repair in minutes with no tools required.
Replaced relay and capacitor attached to compressor Read more
Fix a noisy or non-cooling refrigerator with this condenser fan motor. Solves overheating compressor issues. DIY-friendly repair with video guide.
I bought the listed condenser fan motor for my Maytag refrigerator. Access to the condenser fan is by removing sheet metal screws of bottom panel with 1/4 in. nut driver. Condenser fan is on left side of rear access area. Remove electrical connector by pressing-in connector release tab with thumb fingernail and pulling on connector. Remove three mounting screws with 5/16 nut driver. Work fan out to the right past the compressor. I used a pair of pliers, as a lever, behind the plastic fan blades... Read more
Refrigerator not cooling or control panel blank? This electronic control board manages temperature, defrost cycles, and compressor operation. DIY repair.
A relay in my refrigerator would periodically click off, causing the compressor motor to stop and the LEDs on the front panel to turn off. This became more frequent until it finally "blanked out" permanently. No cooling, no lights on the front panel, no water or ice, only the inside lights worked. Isolating the problem to the control board was easy, and replacing the control board was very easy thanks to the videos and previous customer reports available here. After installing the board, I... Read more
Fix water leaking from your refrigerator or a non-working dispenser with a dual water inlet valve replacement. DIY repair takes 15-45 minutes.
Being an ex maintainence. person, I went down and turned off the water supply. Then I started to try to find the leak by removing the rear covers for the compressor and valves. Once removing a couple of covers where the dual valve was, I spotted where the water was coming from.I then pulled the electrical plug from the wall. Between the solenoid and valve. I removed the screws that held the valve in place. Then disconnected the three hoses going into valve and removed the two electrical... Read more
Ice dispenser not working or only dispensing sometimes? The auger motor powers ice ejection from the storage bin. DIY-friendly repair in under an hour.
I first thought it was the auger in the ice container so I changed it and it was not the problem. I then talked to ApplianceParts customer service that it might be the yoke on the motor that turned the auger or even the motor itself even though it worked. I ordered the parts, the yoke was supposed to be able to be changed by itself but mind would not come off the motor shaft so I had to cut it off just to remove it from the unit so I had to change the motor anyway because of this. So I advise... Read more
Secures your refrigerator's water filter in place for proper filtration. Replace if cracked, chipped, or filter won't stay locked. Confirm fit by model number.
Used screwdriver to push in plastic tabs holding old unit to the top of the refrigerator box Read more
Ice maker won't stop making ice? The shut off arm senses when the bin is full and stops production. Easy 10-minute DIY fix—just snap into place.
We bought a new ice guard and installed it. It is working really good now. Read more
Touch-up paint for covering scratches, chips, and minor blemishes on appliance exteriors. Restores appearance and protects surfaces when finish is damaged.
Touch up paint Read more
Covers the base of your refrigerator to protect the lower ventilation area. Replace if cracked, broken, or missing. Snaps into place in minutes.
Called in. Talk to a sale rep. Told them the model number, told me that this part would work. Shipped it to me. Snapped it in about 30 seconds. Part was perfect. Read more
White acrylic spray paint for appliance exterior touch-ups. Restores worn, chipped, or scratched surfaces on refrigerators, ranges, and more. 13 oz can.
Replaced It With New One Read more
Refrigerator making noise or not cooling? A broken condenser fan blade prevents air circulation. This friction-fit part installs in minutes—no tools needed.
I pulled the refrigerator out, removed the back panel, disconnected the fan motor. I did not know how hard or easy it would be to remove the fan from the motor shaft so I removed the motor with the fan attached and then removed and replaced the fan. This would not be necessary if you have a lot of strength, but if you need leverage to push the fan down on the shaft you might want to disconnect and remove the motor fan assembly too. After replacing the motor assembly and reconnecting I tested by... Read more
Mounting screw for refrigerator ice maker assembly. Secures components to maintain structural integrity. Replace if lost, stripped, or corroded.
Took off the freezer door, took off the top hinge on the refrigerator door, replaced the handle, re-installed the top hinge and the freezer door. This is a two person job - one to remove the top hinge and replace the handle, while a second person holds the refrigerator door in place. Replacing the handle was easy. The most irritating part was figuring out what parts to order. The drawing of the refrigerator door (Drawing # 4) used to figure out what parts to order was not clear. I paid $8... Read more
Gray door closer cam for bottom-mount refrigerators. Installs at the hinge to enable smooth closing and door stay-open function. Replace if cracked or worn.
Replaced door closure and door stop. Read more
Replacement water filter cover for refrigerators. Snaps into place to protect and secure the water filter. Replace if cracked, broken, or latch damaged.
I changed the filter since it had been a long time since last being installed. Still no ice. I used a hair dryer to warm the water line entering the top of the ice maker in case it was frozen. Still no ice. I then ordered and replaced the water inlet valve. Still no ice. I then ordered and installed the ice maker motor module by following the replacement video that was provided when I ordered the part. After the wiring harness was reattached I heard the tray begin to fill with water. We... Read more
Ice maker not filling or water leaking inside your fridge? This water inlet valve controls flow to your ice maker and dispenser. Takes about 25 minutes.
The dual inlet valve was the problem. The hardest part of the repair was moving the refrigerator so we could unplug it. The whole job took about 25 minutes and that includes the time we spent emptying and reorganizing the shelves. I love AppliancePartsPros.com. We have used this website to fix our oven, washer, dryer and now the ice maker. Thank you AppliancePartsPros! We only used one screwdriver and that was only used to open the back panel of the refrigerator. Read more
Ice maker stopped working or freezing up? This complete ice maker assembly fixes no ice production and ice blockages. DIY-friendly, 20-minute install.
I first read some threads on the topic and figured out it was probably the ice maker. I found the part cheaper somewhere else but if it wasn't the problem I couldn't return it. I figured it was worth a little extra money to be able to return it if I was wrong and it was something else. I ordered the part watched the tutorial on YouTube , and replaced it. The only trouble I had was getting the wire harness to stay to the side to get the ice maker back in. I finally taped it down. I fixed it!... Read more